Anthem Ltx-500 Lcos Projector Instructions

 
 
ENGLISH
21
Getting StartedPreparationBasic OperationTroubleshooting
Settings
Others
Connecting via SCART-RCA Cable



































● Set lCOMP.z in the setting menu to lSCARTz(P35 - 12 )
Connecting via RGB Video Cable




● Set lCOMP.z
in the setting menu to lRGBz(P35 -
12


● For information on compatible input signals, see lSpecifi cationsz. (P58)
RS-232C
This unit
To RGB video input terminals
RGB video cable
(sold separately)R(Red)
B(Blue)
G(Green)
(Includes sync signals)
RGB...

Preparation
22
Connecting(Continued) 
SYNCSYNC






● Do not supply the power to the other devices.
● Do not connect audio terminals of the other devices such as 
headphones etc. Otherwise, this may cause a
 malfunction of 
the other devices or injury. 
● Using beyond the rated value will cause malfunction.
●  Exercise adequate caution to prevent short circuit as the trigger 
terminal outputs a voltage of 12V.
Screen

 

Connecting via Trigger Cable
CAUTIONTrigger cable
 (sold separately) To Trigger...

 
 
ENGLISH
23
Getting StartedPreparationBasic OperationTroubleshooting
Settings
Others
   
Installing the Projector and Screen 
While installing, please place this unit and the screen perpendicular to each other. Failing to do so may 
increase trapezoidal distortion. Please refer to 
lKeystonez. (P38 - 25 )
 
 

SetAngle

● The angle range which can be set for this unit is ±10°.
  

● Malfunctions may occur if the angle is not set within the above-mentioned range.



Shift Adjustment
...

Preparation
24
Installing the Projector and 
Screen(Continued)
2
Adjust such that the projected image is in the center of the screen
● It may be necessary to set lPixel Adjustz in the setting menu after adjusting the image position. (P38 - 23 )
BACKBackOperateSelectExitMENU
Focus Lens Control
BACKBackOperateSelectExitMENU
Zoom Lens Control
BACKBackOperateSelect
Shift Lens control
LENSLENS
LENSLENS
LENSLENS
1
3
2
4 Adjust the image position to the center of the screen by pressing  (the up, down, left and...

 
 
ENGLISH
25
Getting StartedPreparationBasic OperationTroubleshooting
Settings
Others

 

Screen Size and Projection Distance
Determine the distance from the lens to the screen to achieve your desired screen size. 
This unit uses a 2.0x power zoom lens for projection. 
■ Relationship Between Projection Screen Size and Projection Distance
Projection Screen Size
(Diagonal Length) 
Aspect Ratio 16:9 Approximate Projection Distance
W
	Wide


to

T
	Tele

Projection Screen Size
(Diagonal Length)


Aspect...

Basic Operation
26
  Projecting Image 
This section describes the basic operations to project input images on the screen.

  WARNING  WARNING
LAMPLAMP
STST ANDBY/ON ANDBY/ON
Preparation
1
Insert the power plug to the power 
      outlet
2 Turn on the power










● You can also press the        button on the unit to turn on the power.
                 (
P15)
            

● The lens cover will be opened.
3
Project the image





1
Select input mode










                              
 
● You can...

 
 
ENGLISH
27
Getting StartedPreparationBasic OperationTroubleshooting
Settings
Others







Adjust the image size (zoom)
● Every time the LENSLENS button is pressed, the adjustment item 
will be switched among “Focus”, “Zoom” and “Shift”. 




 )RFXV
=RRP
6KLIWLENSLENS                    




3

To end
6  Turn off the power






● When power off, the lens cover will be closed.
● The power cannot be turned off within approximately 90 seconds
    after it has been turned on. Start operation only after...

Basic Operation
28
  Convenient Features during Projection 
You can change the screen size of the projected image or hide the surrounding area of an image for which 
quality at the outer area has deteriorated.

 
Setting the Screen Size
The projected image can be set to a most appropriate screen size
(aspect ratio).
● The screen size can also be set from lAspect(Video)z of the setting menu.
      (
P36 - 16 )
● When PC signals are input, the lAspect(Computer)z setting will be available  
      instead....

 
 
ENGLISH
29
Getting StartedPreparationBasic OperationTroubleshooting
Settings
Others
MENU
2
Mask the image 













1
Display the setting menu






2
Select lInput Signalz
 lMaskz






3
Set a mask value
Example:
When the lMaskz value is 
changed from lOffz 
 l5%z
3
To end 
MENUExitBACKBackSelectOperate
   0   0   0   06500KNormal
Picture ModeContrastBrightness
Color
Tint
Color Temp.
Gamma
Advanced
Lens Aperture  Picture Adjust
Natural
Reset
   0
Video/S-Video COMP.Picture Position...

Settings
30
  Setting Menu 
Projected images can be adjusted to a desired view by changing the initial settings.
Procedures for Menu Operation
Example:



When changing lAspect(Video)z
from l4:3z to l16:9z
1
Display the setting menu
2
Select lInput Signalz
 lAspect(Video)z
3

Set to l16:9z
4

To end
MENU
MENUExitBACKBackSelectOperate
   0   0   0   06500KNormal
Picture ModeContrastBrightness
Color
Tint
Color Temp.
Gamma
Advanced
Lens Aperture  Picture Adjust
Natural
Reset
   0
Zoom
ExitMENUBACKBack...