Anschutz Small Bore Rifle Biathlon Small Bore Target Rifle1827 F User Manual

27
considered. (Note: the sequence and
position of the parts can be seen from the
drawing)
¥When the thumb spring is screwed in
(approx. 4 turns) make sure that the nut
plate is vertical to the set screw.
¥Before assembling the rear bolt part and
the bolt clamping sleeve insert the balls
into the rear bolt part from inside (If yougrease them a little they will not fall out).
¥To reassemble the bolt parts attach the
screwed conduit sleeve with its teeth
opposite to the direction of fire to the rear
bolt...

28i r
etuo
pa sd f
Trigger adjustments
1. Trigger weight
Adjust the trigger weight with set screw
No. 10 (silver screw):
¥if you turn it to the right:
trigger weight is increased (+)
¥if you turn it to the left:
trigger weight is decreased (-)
Trigger weight and first stage weight
depend on each other with regard to the
mechanic mechanism. If one of them ischanged there will always be a corres-
ponding change of the other as well.
To move trigger cam No. 11:
¥lowest position of the trigger cam:
lowest...

29
¥if you turn it to the left:
first stage weight is decreased (-)
Trigger weight and first stage weight
depend on each other with regard to the
mechanic mechanism. If one of them is
changed there will always be a corres-
ponding change of the other as well.
Attention:
Do not reduce either trigger weight screw
to zero or lower as the trigger pull may
become erratic.
3. Sear engagement
The sear engagement is the distance bet-
ween the second stage and the release of
the trigger.
Important note:
To...

30
Adjustment of first stage with set screw No. 4:
¥if you turn it to the right:
first stage is shortened
¥if you turn it to the left:
first stage is extended
Attention:
Set screw No. 4 (first stage) can be turned
past the second stage function. In this case
the trigger does not work anymore.
Danger! Do not under no circumstances
remove the first stage completely in order
to change the two-stage trigger into a sin-
gle stage trigger.
5. Trigger stop:
The trigger stop is the distance from the se-
cond...

31
there might be a malfunction and an
increased risk (inadvertent shot
release).
8. Change of single stage trigger into
two-stage trigger
¥Turn trigger stop set screw No. 8 approx.
2 
1/2 turns to the left (adjust max. trigger
stop longer).
¥Release the safety of the trigger and cock
the rifle.
¥Turn set screw No. 5 approx. 2 
1/2  turns
counter-clockwise.
¥You should now feel a second stage
¥To adjust the optimum sear engagement
proceed according to paragraph 3.
¥Perhaps you have to adjust the first...

32
Dry firing device
The length of the firing pin is adjusted so
that it definitely ignites the cartridges. If there
is no cartridge or cartridge case in the
chamber, the firing pin as well as the rim of
the chamber may be damaged when
dryfiring for a longer period. In order to
prevent any possible damage use either a
cartridge case (after about 5 practice shots
insert a different case) or preferably a tone
down disc 1927F-40. With this device you
can practice under competition conditions
without having...

33
Sight Set
Assembly
The rear sight is pushed onto the rail of
11 mm width and fixed with the 2 screws
(tighten manually).
Vertical and horizontal adjustment
The screws for vertical and horizontal
adjustment have clicks. The impact point
changes from click to click.
¥Shots are too high:
Turn knob into ãHÒ direction
¥Shots are too low:
Turn knob into ãTÒ direction
¥Shots are too far at the right:
Turn knob into ãRÒ direction
¥Shots are too far at the left:
Turn knob into ãLÒ direction
Zeroing
After test...

34
many residues would remain in the barrel
at low temperatures.
After initial shooting:
¥Dry clean (remove powder residues).
¥Leave the rifle locked and the snow cap
closed, do not take into a warm room.
After competition:
¥Warm up rifle with opened bolt and snow
cover to room temperature.
¥Carefully remove condensed water on the
external parts.
¥Disassemble bolt and also remove con-
densed water from the individual parts.
Oil with a suitable gun oil.
¥Carefully clean the interior of the barrel
with a...

35
Copyright
Product specifications, design and model
changes are subject to change without prior
notice. Dimensions and colors are subject
to change. With reservation of misprints and
errors. Goods are subject to prior sale.
Delivery subject to the presentation of the
referring license for the purchase of
firearms.
ANSCH†TZ, the ANSCH†TZ logo and the
ANSCH†TZ logo in connection with the
slogan ãDie Meister MacherÒ (also in
modified spelling) and ãSoft-Link¨Ò are
protected brands of J.G. ANSCH†TZ
GmbH &...

45
FABRIKATIONS-NR.:
Serial-No. / NumŽro de sŽrie:
DATUM DES VERKAUFS:
Date / Date dÔachat:
GEKAUFT BEI:
This item was bought from / DŽtaillant:
Stempel und Unterschrift des FachhŠndlers
stamp of dealer / timbre du dŽtaillant
$
Dieser Artikel wurde zum Verkauf freigegeben, nachdem er
selbst, seine Materialien und Einzelteile strenge Kontrollen
durchlaufen haben, oder das Gewehr beim Beschuss seine
Haltbarkeit und Funktion unter Beweis gestellt hat. Wir Ÿber-
nehmen fŸr zwei Jahre volle Garantie auf...