Analog Devices HPUSB USB and HPPCI Emulator Users Guide Rev 32

							HPUSB, USB, and HPPCI Emulators User’s Guide 4-1 
4 REFERENCES
This section describes documentation resources helpful in your applica-
tion development.
 For information on designing the interface between an Analog 
Devices SHARC processor and the emulation header on your 
custom processor target board, refer to Engineer-to-Engineer Note, 
Analog Devices JTAG Emulation Technical Reference (EE-68), 
available from the Analog Devices Web site. 
 For information on the architecture and system interface of the 
Analog Devices processor, refer to the appropriate Analog Devices 
processor’s hardware reference manual.
 For processor timing specification and other hardware design 
information, refer to the appropriate processor’s data sheet.
 For complete information on software development tools 
(assembler, compiler, linker, and so on), refer to documentation 
included with CrossCore Embedded Studio or VisualDSP++. This 
information also is available in the online help and PDF format in 
the 
Docs folder. 
						

							4-2 HPUSB, USB, and HPPCI Emulators User’s Guide  For information about your development platform, refer to your 
operating system manuals and hardware system manuals.
 For information about digital signal processing theory and 
applications, consult:
Digital Signal Processing In VLSI. 
Prentice-Hall, 1990.
 Oppenheim and Schafer. Digital Signal Processing. 
Prentice-Hall, 1975. 
						

							HPUSB, USB, and HPPCI Emulators User’s Guide I-1 
IINDEX
Numerics
1.8V LED, 2-1, 2-3
2.5V LED, 2-1, 2-3
3.3/5V LED, 2-2, 2-3
A
assembly, 1-2
auto detection mode, 1-14
B
board LEDs, 2-4
C
cables, 1-2
CMOS signals, 1-14
Configurator utility, 1-11
connecting USB cable, 1-4
contents, emulator package, 1-2
custom processor boards, 2-5
D
data sheets, 4-1
default setting, 1-12
designing custom boards, 2-5
Device Manager window, 1-5
digital signal processing theory, 4-2
documentation resources, 4-1
drivers, 1-5
E
EE-175, 1-2, 1-16
EE-68, 1-7, 2-5, 4-1
emulator troubleshooting, 1-2, 1-16
enable LED, 2-2, 2-3
F
factory default setting, 1-12, 1-13
frequency, 2-5
full/high speed USB port,   -viii, 1-3
H
hardware
description, 2-1
references, 4-1
high-speed USB device,   vii
HPPCI-ICE
installation, 1-4
JTAG I/O voltage detection, 1-11
LEDs, 2-2
legacy mode, 1-12
mechanical specifications, 2-5
voltage support,   viii
I
installation tasks, 1-3
IOVDD input, 1-13
I/O voltage,   vii,   viii 
						

							Index
I-2 HPUSB, USB, and HPPCI Emulators User’s Guide
J
JTAG
clock frequency,   viii, 2-5
See also TCK
daughter card, 1-2
frequency selection, 1-8
header, 1-11, 1-14, 2-5
port, 2-5
signals, 1-11, 1-14
voltage I/O detection, 1-11
JTAG Frequency Selection dialog box, 1-7, 1-10
L
LEDs
1.8V LED, 2-1, 2-3
2.5V LED, 2-1, 2-3
3.3/5V LED, 2-2, 2-3
enable LED, 2-2
HPPCI-ICE, 2-2
HPUSB/USB ICE, 2-1
legacy mode, 1-13
M
multiprocessor support,   vii,   viii
O
operating systems, 1-3
P
PC configuration, 1-2
PCI based emulators, See HPPCI-ICE
PCI slot, 1-3
plug-n-play,   vii,   viii
pod
assembly, 1-2
cable, 1-5
LEDs, 2-2
Q
quality assurance, 3-2
S
saving selected frequency, 1-10
session restarting, 1-10
status, 1-10
T
technical support,   x, 3-1
Test Clock signal (TCK), 1-8, 1-10
testing JTAG frequency, 1-10
U
USB based emulators
installing, 1-3
LEDs, 2-1
legacy mode, 1-11
USB port, 1-3
voltage support,   viii
USB port, 1-4
V
VDDIO signal, 1-11, 1-14
verifying driver installation, 1-5
voltage
compliance, 1-14
compliance levels,   viii, 1-14