Amptron iFinity Wireless IndoorOutdoor Speaker Speak1 user manual

User and Installation
Guide
Digital Wireless
Indoor / Outdoor SpeakeriFiniy t
TM
R 

Contents:
Unpacking .......................................................................................
Connecting power ...........................................................................
Selecting the audio channel ...........................................................
Turning on speaker power ..............................................................
Pairing the speaker and transmitter ................................................
Setting the speaker volume and treble...

Connecting power
After placing the speaker in a safe environment, make sure that you
have not yet plugged the AC adapter into an outlet. Next, insert the
barrel-shaped plug of the supplied AC adapter into the opening at the
rear of the speaker which says “DC 36V“.
Ensure that you insert the plug straight into the opening (do not angle
it). Push it until it is inserted securely.
Next, plug the AC adapter into a power outlet. Unpacking:Check that this package contains:
One speaker, one AC adapter...

DC 36 V
Power outlet
AC adapter
LeftRight Mono
TrebleVo l u m ePairing Network
DC 36V
OffOn
iFiniy t
TM
User and Installation GuideR
Page 2Connecting power 

LeftRight Mono
TrebleVo l u m ePairing Network
DC 36V
OffOn
iFiniy t
TM
User and Installation GuideR
Page 3

Selecting the audio channel
Slide the audio-channel switch to the audio channel which you want
the speaker to receive. You can either receive the left audio channel,
the right channel or a mix between both channels (mono).
If you are using two wireless speakers in one room, you want to set
one speaker to receive the left channel and one speaker to receive
the right channel.Channel-select switch 

LeftRight Mono
TrebleVo l u m ePairing Network
DC 36V
OffOn
iFiniy t
TM
User and Installation GuideR
Page 4

Turning on speaker power
Turn the speaker volume control to the minimum position.
Next, slide the on/off switch into the “On“ position.
The network status light should start flashing.On/Off switch
Network
status light
Volume control
Turn to
minimum 

LeftRight Mono
TrebleVo l u m ePairing Network
DC 36V
OffOn
iFiniy t
TM
User and Installation GuideR
Page 5

	Pairing the speaker and transmitter
To receive audio from the transmitter, set the transmitter into pairing
mode by pushing the transmitter pairing button.
Then, push the pairing button of the speaker within 5 minutes.
After the speaker is paired with the transmitter, the network status
light will stop flashing and light continuously and the speaker should
output the audio from the...

LeftRight Mono
TrebleVo l u m ePairing Network
DC 36V
OffOn
iFiniy t
TM
User and Installation GuideR
Page 6


Setting the speaker volume and treble
Now slowly increase the volume control.
Use the treble control to adjust the treble of your speaker.
Please follow the instructions in the transmitter user guide for
adjusting the transmitter properly to your audio source in order to
maximize the dynamic range of your speaker.
Treble controlVolume control 

User and Installation GuideR
Page 7
Troubleshooting
Problem
No Sound - Network
status light is OFF
No Sound - Network
status light is
FLASHING
No Sound - Network
status light is ONPossible Cause
AC adapter not
plugged in properly
Speaker not
switched on
No wireless signal
Speaker not paired
with transmitter
Strong interference
Volume control set
too low
No audio at
transmitterSolution
Check AC adapter for
proper fit
Slide the speaker on/off
switch to the “On“ setting
Check if the transmitter is
active...

User and Installation GuideR
Page 8
Technical Specifications
Amplifier:
Amplifier Power:
Drivers:
Crossover:
Frequency response (-6 dB):
Amplifier distortion (THD):
Power efficiency:
Max. number of speakers
per transmitter:
Size:
Weight:
Standby power:Bi-amplification: two separate
Class-D amplifiers
150W peak, 80W rms
5 woofer, 1 tweeter
Active
60 Hz - 18 kHz
0.06% @ 50 Watts
91%
4
8.5 (H) x 8.5 (W) x 8.3 (D)
4.8 lbs
< 3W