AltiGen comm AltiGen IP Phone IP705 User Manual

IP 705 Manual 13
CHAPTER 2 
Setting Up the IP 705 Phone
To set up the IP 705 phone, follow these instructions:
1. Gather network settings information (this information is needed to 
configure the IP 705):
• AltiWare server IP address 
• IP 705 phone’s IP address
This address is needed if your company does not use Dynamic Host 
Configuration Protocol (DHCP), which automatically assigns IP 
addresses to devices when they are connected to the network. The 
phone’s IP address can be obtained from your system...

14     IP 705 Manual   
4. Configure the AltiWare IP settings (see 
“Configuring IP Settings” on 
page 20  for information about IP settings):
a.  Menu  > SYSTEM > Enter.
b.  Select  AW SERVER,
  and press Enter.
c.  Enter the AltiWare server address, using the * key to input periods, 
and press  Enter.
5. Activate the IP 705 extension from the IP phone:
a. With the handset  on
 hook, press  #27, then the  Enter button.
b.  Enter the extension number and password when prompted.
c.  The phone will attempt...

Setting Up the IP 705 PhoneIP 705 Manual  15
—
LOADING FW...
— LOADING NOW.
— Boot Done
— INITIALIZING 
— Version xxxx.xxxx.xx
 xx
To Use IP 705 in Power over Ethernet Mode
1. Unplug the power cord.
2. Remove the screw on the PoE Module cover, and remove the cover.
3. Plug in the PoE Module as illustrated below. The side with four pins 
in
  the center  faces the right side.
Right
Left
4. Put the PoE module cover back, and tighten the screw.
5. Move the DC/PoE switch to the PoE position.
6. Connect the...

16     IP 705 Manual  
Miscellaneous Operation Notes
•Logging in and out—When using #26 and #27 to log out / log in, the 
IP 705 must be onhook. Pressing the Speaker button and then using 
#26 or #27 will not work.
•BASIC mode—If the IP 705 phone fails to register with AltiWare 
during startup, the phone operates in Basic mode. When in Basic 
mode, the IP phone’s LCD display shows (BASIC) IDLE. 
No AltiWare switching features are available in this operating mode. 
However, the phone user can enter a...

IP 705 Manual 17
CHAPTER 3 
Configuring the IP 705 Phone
Phone, system, and network settings can be configured through the IP 
phone’s menu. The phone can also be registered through this menu, if 
necessary.
• To get to the menu, press the Menu button.
•/ buttons scroll the menus and settings in the LCD screen. 
• button selects a menu item or a setting. 
• The Enter button also selects a menu item or a setting.
• button returns to the previous menu.
•Press the Release button to exit the menu.
The...

18     IP 705 Manual  
System Settings
Ring TonePhone Setting > 
Ring TonesSets the desired ring tone.
Ring 
DownloadPhone Setting > 
Ring DownloadDownloads ring tones from the 
server.
Auto AnswerPhone Setting > 
Auto AnswerSets whether to enable automatic 
answering.
Auto Answer 
RingPhone Setting > 
Auto Ans RingSets how many seconds the phone 
should ring before it is automatically 
answered. Appears on menu when 
Auto Answer is set to Yes.
Auto Answer 
DevicePhone Setting > 
Auto Ans DevSets whether...

Configuring the IP 705 Phone
IP 705 Manual 19
Network Settings
Emergency 
NumberSystem >  
Emergency NumSets the IP phone’s emergency 
number. For the U.S., the emergency 
number is 911.
Emergency 
GatewaySystem >  
Emergency GW Sets the IP phone’s emergency 
gateway IP address
Version 
InformationSystem >  
Version Info  
[Read only]Displays the version number of the 
IP phone.
SIP RegisterSystem > Enable SIP 
RegistrationEnables SIP registration to the 
emergency gateway 
Auto-
discoverSystem > Auto...

20     IP 705 Manual  
Registration from the Phone’s Menu
Under normal circumstances, the IP 705 phone registers itself 
automatically. However, if registration failed for some reason (for 
example, the server was not available), registration can be started again 
from the IP 705 phone’s menu: 
1. Press the Menu button.
2. Scroll to REGISTER.
3. Press the Enter button.
Configuring IP Settings
An IP address is a unique logical address that identifies each host computer 
on a TCP/IP network. An IP address...

Configuring the IP 705 Phone
IP 705 Manual 21
4. Use the keys on the dial pad to enter a new IP address, using the * key 
to enter periods.
5. Press Enter.
Assigning a TFTP Server
The default TFTP Server is set to 0.0.0.0.
To assign the TFTP server, use the following steps:
1. Press the Menu button.
2. Use  to select System, then press the Enter button.
3. Scroll to TFTP Server, and press Enter.
4. Use the keys on the dial pad to enter the new TFTP server address, 
using the * key to enter periods, then...

22     IP 705 Manual  
—LOADING FW...
—LOADING NOW.
—Boot Done 
—INITIALIZING
—Version xxxx.xxxx.xxxx
10. You may display the version of firmware at any time: Press the Menu 
button, scroll to SYSTEM and press Enter, scroll to Version Info 
and press Enter.
Configuring NAT
Note:This section is only for an IP 705 phone that is using an H.323 
version of AltiGen phone firmware. 
NAT (Network Address Translation) is the translation of an IP address 
used within one network to a different IP address known...