Alpha Tool.Com.HK Limited Ecocaddy User Manual
Here you can view all the pages of manual Alpha Tool.Com.HK Limited Ecocaddy User Manual. The Alpha Tool.Com.HK Limited manuals for Ecocaddy are available online for free. You can easily download all the documents as PDF.
Page 11
11 screw on lock Nut b to Dust hose holder them secure Dust hose holder temporary by using lock Nut A. sTEP 9 Assembly of Ecogrinder Caddy cont’d lock Nut A lock Nut b Dust hose holder Dust hose holder lock Nut b lock Nut A
Page 12
12 sTEP 10 Insert handle Post to handle hold Assembly then secure at the desired height using the Knob bolts. Assembly of Ecogrinder Caddy cont’d
Page 13
13 ECOGrINDEr OVErVIEW sPECIfICATIONs Power supply ............................................................. single-Phase AC, 50/60 hz rating ................................................................................................ 110/220 Volts Amperage ................................................................................................. 10.25/5.1 Power .....................................................................................................\ ...... 1050W No-load...
Page 14
14 CAuTION! The following are important notes for products, operation, and maintenan\ ce ap- plicable to this polisher. GENErAl sAfETy rulEs WOrK ArEA • Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. • Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools may create sparks which may ignite the dust or fumes. • Keep bystanders, children, and visitors away while operating a power...
Page 15
15 Ampere ratingTotal length of cord in feet (120V ) 25ft 50ft 100ft More Than Not More Than AWG 0 6 18 16 16 6 10 18 16 14 10 12 1616 14 12 16 1412 Not recommended GrOuNDING INsTruCTIONs This tool should be grounded while in use to protect the operator from electric shock. The tool is equipped with a three-conductor cord and three-prong grounding type plug to fit the proper grounding type receptacle. The green (or green and yellow) conductor in the cord is the grounding wire. Never connect...
Page 16
16 ATTAChING ThE ECOGrINDEr TO ThE CADDy 1. loosen the two screws from the handle of the Ecogrinder. save original Grip and bolts for future use. 2. Install supplied screws and Nuts to pre-assemble as a hanger bolt. 3. Insert the Power Cord through the Motor support Assembly, then slide the Grinder into the Motor holder. OPTIONAl ACCEssOrIEs (ITEMs sOlD sEPArATEly)
Page 17
17 4. Insert the two slots in between the handle brackets and the Washers, attach to the hanger bolt. Tighten lightly. 5. When installation is completed, tighten the s crews to secure the Grinder to the Caddy. 6. Adjust the Knob bolt up or down to level the Ecogrinder against the floor. 7. Tighten the screws and the Wing Nuts to secure the level of the Ecogrinder on the Ecocaddy. OPTIONAl ACCEssOrIEs (ITEMs sOlD sEPArATEly)
Page 18
18 AssEMbly 1. Insert front rail with hose supporter facing outwards into the T-fittings at the front of the Carriage b ase (Note: the front of carriage base has s wivel Wheels for easy maneuvering). Align clearance holes on rail with holes on T-fittings. Insert the supplied screws on both ends and hand-tighten with a screw driver. 2. Insert back rail into the T-fittings at the back of carriage base (Note: the back of the carriage base has fixed Wheels). follow steps for tightening the rail...
Page 19
19 ATTAChING ThE DusT bAG 1. Using a flat-head screwdriver, remove the Hose Band from the Hose Supporter. Insert the h ose End into the mouth of the Dust b ag. Place in the hose supporter and secure with the Hose Band. Tighten to a snug fit. 2. secure the Dust bag to the dust bag carriage by tying each end to the Tie support rings located on the rails of the dust bag carriage. The lower front tie\ s can be tied to the rail of the carriage base as shown in the photo above\ . NOTE: The Dust...
Page 20
20 ATTAChING ThE DusT hOsE TO ThE ECOGrINDEr 1. Insert Dust hose through Dust hose holder as shown below. 2. Install the dust gate with anti-back-flow flap to the Ecogrinder exhaust port. Make sure the dust gate is in the upright position, so flap will close when the tool is turned off. 3. slide the dust hose onto the dust gate, twist and turn until the hose is up against the shoulder for a snug fit. 4. Adjust lock Nut A and lock Nut b of Dust hose holder to secure Dust hose. Dust hose Dust...
All Alpha Tool.Com.HK Limited manuals