Alpha Tool.Com.HK Limited Ecocaddy User Manual

							11
screw on lock Nut b to Dust hose holder them 
secure Dust hose holder temporary by using 
lock Nut A.
 sTEP 9
Assembly of Ecogrinder Caddy cont’d
lock Nut A lock Nut b
Dust hose holder
Dust hose holder
lock Nut b
lock Nut A   
						

							12
 sTEP 10
Insert handle Post to handle hold Assembly 
then secure at the desired height using the 
Knob bolts. Assembly of Ecogrinder Caddy cont’d   
						

							13
 ECOGrINDEr OVErVIEW
  sPECIfICATIONs
Power supply ............................................................. single-Phase AC, 50/60 hz
rating ................................................................................................ 110/220 Volts
Amperage ................................................................................................. 10.25/5.1
Power .....................................................................................................\
...... 1050W
No-load speed ...................................................................................... 8,700 rPM
Wheel size ............................................................................................ 5” / 125mm
Arbor  .....................................................................................................\
........ 26mm 
 (
To be used with spring loaded flange Assembly and Drive Plate Adapter) 
Arbor  ............................................................................................... 7/8” / 22.23mm
 (
To be used with Manual height Adjustment flange Assembly) 
Weight ..................................................................................... 12.70 lbs / 5.76kgs
 
(Tool w/hose and bag)
Cord ....................................................................................................\
...... 10ft / 3m
                                              (single Phase 2 Conductor)
Protective Grinding
Wheel Cover
Aux handle
Dust brush
Edge Grinding
slide Cover
slide Cover
Knob fan Case
spindle 
locking Pin
fan belt Cover
Power switch
Power switch
lock 
OPTIONAl ACCEssOrIEs (ITEMs sOlD sEPArATEly)  
						

							14
  CAuTION!
The following are important notes for products, operation, and maintenan\
ce ap-
plicable to this polisher.
GENErAl sAfETy rulEs
 WOrK ArEA
•  Keep your work area clean and well lit.  Cluttered benches and dark areas 
invite accidents.
•  Do not operate power tools in explosive atmospheres, such as in the 
presence of flammable liquids, gases, or dust.  Power tools may create 
sparks which may ignite the dust or fumes.
•  Keep bystanders, children, and visitors away while operating a power 
tool. Distractions can cause you to lose control.
 ElECTrICAl  sAfETy
•  Grounded tools must be plugged into an outlet properly installed and 
grounded in accordance with all codes and ordinances. Never remove 
the grounding prong or modify the plug in any way. Do not use any adaptor 
plugs. Check with a qualified electrician if you are in doubt as to whether the 
outlet is properly grounded.  If the tools should electrically malfunction or break 
down grounding provides a low resistance path to carry electricity away from 
the user.
•  Avoid body contact with grounded surfaces, such as pipes, radiators, 
ranges, and refrigerators.  There is an increased risk of electric shock\
 if your 
body is grounded.
•  Don’t expose power tools to rain or wet conditions.  Water entering a power 
tool will increase the risk of electric shock.
•  Do not abuse the cord.  Never use the cord to carry the tools or pull the plug 
from an outlet.  Keep cord away from heat, oil, sharp edges, or moving parts.  
replace damaged cords immediately.  Damaged cords increase the risk of 
electric shock.
•  When operating a power tool outside, use an outdoor extension cord 
marked “W-A” or “W”.  These cords are rated for outdoor use and reduce 
the risk of electric shock.
 
  usE PrOPEr EXTENsION COrDs
use only three-wire extension cords that have three-prong grounding-type \
plugs and 
three-pole receptacles that accept the tool’s plug.  Make sure your extension cord 
is in good condition.   replace or repair damaged or worn cord immediately.  When 
using an extension cord, be sure to use one heavy enough to carry the cu\
rrent your 
product will draw.  An undersized cord will cause a drop in line voltage resulting in 
loss of power and overheating.  b elow table shows the correct size to use depend -
ing on cord length and nameplate ampere rating.  If in doubt, use the ne\
xt heavier 
gauge.  The smaller the gauge number, the heavier the cord. 
OPTIONAl ACCEssOrIEs (ITEMs sOlD sEPArATEly)  
						

							15
Ampere ratingTotal length of cord in feet (120V )
25ft 50ft 100ft 
More 
Than Not More 
Than AWG
0 6 18 16  16
6 10 18 16 14
10 12 1616  14
12 16 1412
Not recommended
  GrOuNDING INsTruCTIONs
This tool should be grounded while in use to protect the operator from electric shock.  
The tool is equipped with a three-conductor cord and three-prong grounding type 
plug to fit the proper grounding type receptacle.  The green (or green and yellow) 
conductor in the cord is the grounding wire.  Never connect the green (or green 
and yellow) wire to a live terminal.
ECOGrINDEr OPErATION
  CAuTION!
Always be sure that the tool is switched off and unplugged before adjust\
ing or 
checking function on tool.
 MAIN CONNECTION
Connect only to single-phase AC current supply and only to the main voltage speci-
fied on the rating plate. 
 sWITChING ON AND Off
  CAuTION!
b efore plugging in the tool, always check the working voltage and be sure that the 
voltage specified is on the name plate.  Before plugging in the tool, always check 
to see that the trigger switch actuates properly and returns to the “\
O ff” position.
switching on and Off:  
Intermittent use:
switching on: Press the trigger switch
switch off: release the trigger switch
Continuous use:
switching on: Press the trigger switch and then the locking button, then release the trig-
ger switch 
switching off: press the trigger switch, then release 
OPTIONAl ACCEssOrIEs (ITEMs sOlD sEPArATEly)  
						

							16
ATTAChING ThE ECOGrINDEr TO ThE CADDy
1. loosen the two screws from the handle of the Ecogrinder. save original Grip and bolts for future use.
2. Install supplied screws and Nuts to pre-assemble as a hanger bolt.
3. Insert the Power Cord through the Motor support Assembly, then slide 
the Grinder into the Motor holder. 
OPTIONAl ACCEssOrIEs (ITEMs sOlD sEPArATEly)  
						

							17
4. Insert the two slots  in between the handle brackets and the 
Washers, attach to the  hanger 
bolt. Tighten lightly.  5. When installation is completed, 
tighten the s crews to secure the 
Grinder to the Caddy. 
6. Adjust the Knob bolt up or down  to level the Ecogrinder against the 
floor. 
7. Tighten the screws and the Wing Nuts to secure the 
level of the Ecogrinder on the 
Ecocaddy. 
OPTIONAl ACCEssOrIEs (ITEMs sOlD sEPArATEly)  
						

							18
 AssEMbly 
1.  Insert front rail with hose supporter facing outwards into the T-fittings at 
the front of the Carriage b ase (Note: the front of carriage base has s wivel 
Wheels for easy maneuvering).  Align clearance holes on rail with holes on 
T-fittings. Insert the supplied screws on both ends and hand-tighten with a 
screw driver.
2.  Insert back rail into the T-fittings at the back of carriage base (Note: the back 
of the carriage base has fixed Wheels).  follow steps for tightening the rail 
as stated above.
back rail
fixed Wheels
T-fitting
swivel 
Wheels front rail
safe board
Tie support 
rings
hose band
hose 
supporter
Carriage 
base
DusT bAG CArrIAGE
DusT bAG AND ACCEssOrIEs
Dust bag
Dust hoseDust Gate with Anti-
back-flow flap 
OPTIONAl ACCEssOrIEs (ITEMs sOlD sEPArATEly)  
						

							19
 ATTAChING ThE DusT bAG 
1.  Using a flat-head screwdriver, remove the Hose Band from the Hose Supporter.  
Insert the h ose End into the mouth of the Dust b ag.  Place in the hose supporter 
and secure with the Hose Band.  Tighten to a snug fit.
2.  secure the Dust bag to the dust bag carriage by tying each end to the Tie 
support rings located on the rails of the dust bag carriage.  The lower front tie\
s 
can be tied to the rail of the carriage base as shown in the photo above\
.
NOTE:  The Dust  bag Carriage can also be used as a 
backpack for vertical applications and easy transport.
front Ties
hose End
Dust bag
To convert to a backpack, hook straps onto 
Tie support rings. 
OPTIONAl ACCEssOrIEs (ITEMs sOlD sEPArATEly)   
						

							20
ATTAChING ThE DusT hOsE TO ThE ECOGrINDEr
1. Insert Dust hose through Dust hose holder as shown below.
2.  Install the dust gate with anti-back-flow 
flap to the Ecogrinder exhaust port. 
Make sure the dust gate is in the upright 
position, so flap will close when the tool 
is turned off.
3.   slide the dust hose onto the dust gate, 
twist and turn until the hose is up against 
the shoulder for a snug fit.  4. Adjust lock Nut A and lock Nut 
b of Dust hose holder to secure 
Dust hose.
Dust hose Dust hose
Dust hose holderDust Gate
lock Nut A
lock Nut b 
OPTIONAl ACCEssOrIEs (ITEMs sOlD sEPArATEly)