Aleratec 13 DVD CD LightScribe Auto Publisher Quick Start Guide

www.aleratec.com9
Bin Configuration
You will be prompted 
1. 
next to choose a bin 
configuration. This 
changes the behavior of 
the autoloader, in relation 
to which bins are used for 
input/output.
It is suggested that the default configuration option should be 
used, unless you specifically desire a different bin order for 
picking up and dropping discs. By default, the autoloader will 
pick up discs from bin 1, and place completed discs into bin 3. 
When bin 1 is empty, the autoloader will (if...

www.aleratec.com
10
Autoloader Alignment
Click on the “Calibration...” 
1. 
button to access the various 
alignment parameters on your 
1:3 DVD/CD Auto Publisher 
LS. There should be no disc in 
any of the recorders to start.
Note: To realign a previously installed autoloader, click on the 
“Recorder” menu and select “Robotics.” On the “Tests” tab of this 
dialog box, click the “Calibration...” button and proceed to the n\
ext 
step.
Each of the alignment 
2. 
parameters can be selected from 
the...

www.aleratec.com11
Use the “Right” and “Left” arrow icons to move the robotic 
4. 
arm clockwise and counterclockwise, respectively. Adjust this 
position as close as possible to the center of the disc and click 
“Accept”, then “OK.”
You will be prompted to save the alignment parameters to a 
5. 
configuration file. Type a name for this file in the “File name” 
box and then click “Save.”
When Droppix asks if you would like to apply the settings as 
6. 
default, click “Yes.” The current alignment...

www.aleratec.com
12
Select the “Height of Robotic Arm” parameter and adjust with 
9. 
the “Up” and “Down” arrow buttons as necessary. The picker 
head should be flush with the surface of the disc on the tray, 
but should not press down so hard as to put undue pressure on 
the tray. Click “Accept” when finished with this parameter, and 
remove the disc from the recorder.
The alignment 
10. 
parameters for Number 
1, 2, and 3 Spindles are 
all performed with a 
stack of 90 discs in each 
bin, with the...

www.aleratec.com13
For the alignment parameter “Down Limit of Spindle,” there should 
12. 
not be any bin present in the “Number 3 Spindle” position. Press the 
“Down” arrow button ten (10) times, during which time the arm will 
move in major increments.
After the large increments, the distance moved down with each click 
will be very minor, and the goal here is to have the bottom edge 
of the vertically-moving picker head carrier even with or no more 
than 1/16 inch (2 mm) above the bottom of the guide...

Document Number: 9299040_ENG_Rev. B  Copyright © 2008
Specifications subject to change without notice.  
Aleratec, Inc.
9851 Owensmouth Avenue
Chatsworth, CA 91311 U.S.A.
 
www.aleratec.com
Technical Support Addresses and
Phone Numbers
By e-mail: 
 
► [email protected]
By Telephone: 
 
► 1-818-678-0484
Technical Support Group can be reached 8:00 AM to 5:00 
PM, Pacific Time, Monday through Friday, excluding U.S. 
holidays.
Please try to call from a phone near your computer system.
Access is available...

Le choix pour les 
professionnels et particuliers
GUIDE DE DÉMARRAGE RAPIDE
AlerateC
1:3 DVD/CD Auto Publisher LS™
Part No. 280106 

www.aleratec.com
Bienvenue !
Félicitations pour avoir acheté le 1:3 DVD/CD Auto Publisher 
LS d’Aleratec, considéré par les experts de l’industrie comm\
e 
l’un des meilleurs duplicateurs DVD/CD qui existent.
Toute l'équipe d'Aleratec a à cœur de vous offrir un service de \
qualité. Notre équipe expérimentée déploiera tous ses eff\
orts 
pour que la possession et l'exploitation de votre nouveau 1:3 
DVD/CD Auto Publisher LS d'Aleratec soit un réel plaisir.
Ce Guide de démarrage rapide...

www.aleratec.com1
Caractéristiques Du Produit
Le duplicateur 1:3 DVD/CD Auto Publisher LS est une solution 
polyvalente de copie de DVD/CD robotique et d’impression 
d’étiquettes LightScribe.
Vitesse d’enregistrement élevée pour une copie de grand 
 
•
volume.
Copie trois DVD ou CD simultanément.
 
•
Fonctionnement simple.
 
•
Logiciel inclus pour simplifier le processus de duplication et 
 
•
assurer un fonctionnement sans problèmes.
Grave des étiquettes LightScribe directement sur des 
 
•
disques...

www.aleratec.com
2
Installation Matérielle
Présentation De La Procédure
Vérifier que le PC est éteint.
1. 
Connecter les câbles.
2. 
Allumer le PC.
3. 
Insérer le CD d'installation.
4. 
Allumer le duplicateur.
5. 
Installer les pilotes.
6. 
Installer les cartouches d'encre.
7. 
Installer le logiciel.
8. 
Connecter Les Câbles
Insérez le câble USB 2.0 dans le connecteur USB situé au centre\
 
à l'arrière du duplicateur 1:3 DVD/CD Auto Publisher LS. Insérez 
l'autre extrémité du câble USB...