Aleratec 111 USB Copy Cruiser SA Stand Alone USB Flash Drive Duplicator User Guide

							www.aleratec.com25
Us\bng the USB Dupl\bc\Cat\fr
6.5 Full Erase USB
Full Erase USB is a function what will erase all data on the target USB flash 
drive. 
N\fte: The Full Erase USB \iwill completely era\ise data of each of t\ihe target 
flash drives This fu\fctio\f will als\io clear the FAT table i\f the flash \idrive. 
You will \fot be able \ito read the flash d\irive o\f PC u\ftil it is\i re-formatted. 
 
1. Use UP or DOWN arrow to scroll through the menu until Utility is 
displayed on the LCD screen. Press the OK button to select or press 
ESC to go to the next setting.
2. Press OK and scroll to Full Erase USB. The LCD will display the 
following status:
3. Press OK to select. The LCD will display the following status:
Press OK for Yes or ESC for No. 
4. LCD display will show the following screen when finished.
6.6 System Update
This function is used to update your systems firmware. (Contact Aleratec 
Technical Support for the latest version.)
ESC
OK

USB Dupl\bcat\fr
6. Ut\bl\bty
ESC
OK

6. Ut\bl\bty
5. Full Erase USB
ESC
OK

D\f Erase All
C\fnfirm?
ESC
OK

Pass: 2 W\frk\bng
Fa\bl: 0  0          
						

							www.aleratec.com26
Us\bng the USB Dupl\bc\Cat\fr
6.7 Calc. Checksum
The Calculate Checksum function computes a checksum for the contents 
of the source drive. This alphanumeric can be used to ensure that no minor 
changes due to alteration or virus have occurred on the source drive since  
its last use.   
 
1. Use UP or DOWN arrow to scroll through the menu until Utility is 
displayed on the LCD screen. Press the OK button to select or press 
ESC to go to the next setting.
2. Press OK and scroll to Calc. Checksum. The LCD will display the 
following status:
3. Press OK to select. Depending on content, some time will be spent 
calculating the Checksum. Once done, the LCD will display the 
calculated Checksum.
ESC
OK

USB Dupl\bcat\fr
6. Ut\bl\bty
ESC
OK

6. Ut\bl\bty
7. Calc. Checksum
ESC
OK

Checksum=
AE5277D9        
						

							www.aleratec.com27
Us\bng the USB Dupl\bc\Cat\fr
Ma\bn Menu
Setup
This function includes 8 subfunctions. These are: 
7.1 Start-up Menu
7.2 C\fpy Area
USB Dupl\bcat\fr
7. Setup
OK
ESC


7.3 Butt\fn Beep
7.4 Asyn H\fld T\bme
7.5 Ign\fre S\bze
7.6 Asynchr\fn\fus Enable/D\bsable
7.7 Language
7.8 W\frk\bng M\fde N\frmal/Turb\f    
						

							www.aleratec.com28
Us\bng the USB Dupl\bc\Cat\fr
7.1 Startup Menu 
Startup Menu allows you to select which function displays first when the USB 
Duplicator is turned on. 
This function selects the menu item that will be the first item shown on the 
display when you turn on the duplicator. The default setting is Copy.
1. Use the UP or DOWN arrow to scroll through the menu until Setup is 
displayed on the LCD screen. Press OK. 
2. Use the UP or Down arrow to scroll through the Setup options until Startup 
Menu is displayed on the LCD screen. 
7.2 Copy Area
This function supports the selection of Quick Copy or Copy whole area of the 
source.
7.2.1 Only Data area – Quick Copy
 If the controller system can verify FAT 16, 32, NTFS, Linux Ext 2, Ext 
3 format for the source, the system will copy just the data area when 
this function is selected. If it cannot verify the format, the system will 
automatically copy the whole area of the source. For example, if a 2GB 
source is FAT 32 and it has 50MB of data, the system will copy only the 
50MB of data. 
7.2.2 Whole area – Controller will copy whole area of the source.
 If the source is not FAT 16, 32, NTFS, Linux Ext 2, Ext 3 format, the 
system will copy the entire media, even the blank area. When this function 
is selected, Quick Copy will not be used. The copy process takes longer. 
ESC
OK

USB Dupl\bcat\fr
7. Setup
ESC
OK

7. Setup:
1. Startup Menu
ESC
OK

Startup Menu
1. C\fpy        
						

							www.aleratec.com29
Us\bng the USB Dupl\bc\Cat\fr
7.3 Button Beep
This setting controls the button sound. 
1. Use the UP or DOWN arrow to scroll through the menu until Setup is 
displayed on the LCD screen. Press the OK. 
2. Use the UP or Down arrow to scroll through the Setup options until 
Button Beep is displayed on the LCD screen. 
3. Default setting is ON. Use the UP or DOWN arrows to select either ON 
or OFF. Press the OK button to change, or ESC to exit.
ESC
OK

7. Setup:
3. Butt\fn Beep
ESC
OK

Butt\fn Beep
On
ESC
OK

USB Dupl\bcat\fr
7. Setup        
						

							www.aleratec.com30
Us\bng the USB Dupl\bc\Cat\fr
7.4 Asyn Hold Time
This function allows you to set the time to exit Asynchronous Copying 
when you pull all the USB flash drives out of the duplicator. The default 
setting is 30 seconds. If after 30 seconds no new drives are plugged into 
the USB Duplicator the LCD will ask to exit Asynchronous or to stay in 
Asynchronous mode. Press OK to exit Asynchronous Copying or press 
ESC to keep this status. 
To change the default setting for Asyn Hold Time use the following 
procedure:
1. Use the UP or DOWN arrow to scroll through the menu until Setup is 
displayed on the LCD screen. Press the OK button to select. 
2. Use the UP or Down arrow to scroll through the Setup options until 
Asyn Hold Time is displayed on the LCD screen. Press OK.
3. Default setting is 30 seconds; press the arrow keys to change. Press 
ESC to exit.
7.5 Ignore Size
To make sure the FAT table of each flash drive was copied correctly all 
source and target flash drives should be the same capacity. Each flash drive 
potentially has some capacity difference due to the manufacturing process. 
To ensure both the source and target flash drives are at the same capacity 
you can set the capacity tolerance. This function is used to set the tolerance 
% of flash capacity difference between source and targets.
ESC
OK

USB Dupl\bcat\fr
7. Setup
ESC
OK

7. Setup:
4. Asyn H\fld T\bme
ESC
OK

Asyn H\fld T\bme
30sec.        
						

							www.aleratec.com31
Us\bng the USB Dupl\bc\Cat\fr
7.5 Ignore Size - continued 
1. Use the UP or DOWN arrow to scroll through the menu until Setup is 
displayed on the LCD screen. Press the OK button to select or press 
ESC to go to the next setting. 
2. Use the UP or Down arrow to scroll through the options until Ignore 
Size is displayed on the LCD screen. Press OK.
3. Default setting is 3% ; press the arrow keys to change and press OK.
N\fte: Source flash drive a\fd bla\fk drives \feed to be the same capacity for two reaso\fs. 
1. Duri\fg the copy proce\iss the source flash \idrive “i\fdex sector”\i is copied to 
the target flash dr\iive. The i\fdex sector of \ia flash drive co\ftai\f\is the drives 
specificatio\fs\b size a\i\fd FAT table. Differe\ft drive sizes wi\ill have differe\ft i\fdex 
sectors. For exampl\ie if your are copyi\fg \ia 2G source flash dr\iive to a 4G target \i
flash drive without p\ierformi\fg data tra\fsf\iormi\fg\b the i\fdex sec\itor of the 2G 
source would be copi\ied to the 4G targe\it flash drive effectively cha\fgi\fg it \ito a 2G 
flash drive because \iof the copied 2G i\fde\ix sector. 
2. If you allow the sys\item to execute data\i tra\fsformi\fg from a \isource flash drive t\io 
multiple target flash\i drive i\f additio\f to\i lo\fger copyi\fg time \ithere is a pote\ftial\i for 
data loss duri\fg dat\ia tra\fsformi\fg.
N\fte: If you \feed to copy \ia source flash to a \itarget with a big c\iapacity differe\fce there 
are two ways to av\ioid pote\ftial problem\is.
1. Use the Setup fu\fctio\f\i Ig\fore Size to i\fcr\iease the tolera\fce \i% of the source a\fd \i
target.
2. Tur\f the Setup fu\fctio\f \iA\falyze Source to O\iFF. 
ESC
OK

USB Dupl\bcat\fr
7. Setup
ESC
OK

7. Setup:
5. Ign\fre S\bze
ESC
OK

Ign\fre S\bze
3%        
						

							www.aleratec.com32
Us\bng the USB Dupl\bc\Cat\fr
7.6 Asynchronous (Enable/Disable)
This function allows the user to enable/disable asynchronous copying. Use 
Up and Down arrow keys to toggle between and push OK to select, or ESC 
to exit. 
7.7 Language
This function selects the language shown on the display (English, 
Traditional Chinese, Simplified Chinese, and Japanese). 
To change the default setting for Asyn Hold Time use the following 
procedure:
1. Use the UP or DOWN arrow to scroll through the menu until Setup is 
displayed on the LCD screen. Press the OK button to select or press 
ESC to go to the next setting. 
2. Use the UP or Down arrow to scroll through the options until Language 
is displayed on the LCD screen. 
3. To select, press the OK button, or ESC to exit. 
7.8 Working Mode (Normal/Turbo)
This function allows the user to select between Normal and Turbo working 
modes. Select using the Up and Down arrow keys and push OK. 
N\fte: Turbo Mode is faster \ibut it will copy err\iors. Normal speed i\is safer. 
ESC
OK

USB Dupl\bcat\fr
7. Setup
ESC
OK

7. Setup:
7. Language      
						

							www.aleratec.com33
Spec\bficat\b\fns
Operating Type• Stand-alone (No PC Required)
Number of Targets• 11
Supported Media• USB Flash/Pen Drive requiring less than 500mA 
from USB Port
Transfer Speed• 128MB/min Typical
Copy Mode• Synchronous or Asynchronous
LCD Display• 2 x 16 Backlit
Power Requirements• 115V or 230V
Operating Temperature• 41°F - 122°F
Operating Humidity • 15% - 90%  
						

							www.aleratec.com34
Techn\bcal Supp\frt
After reading this User Guide, if you need additional assistance with this 
product, please contact Aleratec Technical Support. Our technical staff will 
be happy to assist you, but they may need your help to better assist you. 
Calling Aleratec Technical Support without all the necessary information 
can be both time consuming and frustrating. Therefore, please try to have 
the following information ready before calling:
1. Part Number - the part number is located on the bottom of the 1:11 
USB Copy Cruiser SA.
2. Serial Number - the serial number is located on the bottom of the 1:11 
USB Copy Cruiser SA.
3. Troubles - your questions about the 1:11 USB Copy Cruiser SA. Please 
provide enough information about your problems so our technical staff 
can recreate and diagnose it.
Techn\bcal Supp\frt Addresses and Ph\fne\C Numbers
 XBy e-mail: [email protected]
 XBy Telephone: 1-818-678-0484
Technical Support Group can be reached 8:00 AM to 5:00 PM, Pacific 
Time, Monday through Friday, excluding U.S. holidays.
Please try to call from a phone near your computer system.
 XAccess is available 24 hours a day, 365 days a year, via:
The World Wide Web at: www.aleratec.com
FAX at: 1-818-678-0483