Home
>
Aleratec
>
Hard Disk
>
Aleratec 111 USB Copy Cruiser SA Stand Alone USB Flash Drive Duplicator User Guide
Aleratec 111 USB Copy Cruiser SA Stand Alone USB Flash Drive Duplicator User Guide
Have a look at the manual Aleratec 111 USB Copy Cruiser SA Stand Alone USB Flash Drive Duplicator User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 61 Aleratec manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
www.aleratec.com15 Us\bng the USB Dupl\bc\Cat\fr Synchronous Copy+Compare - continued 4. Finish loading the blank target flash drives, then press the OK button on the display panel. 5. The LCD will display the status of the copying process. 6. When Copy is complete LCD will display the following status: If the Copy fails, the LCD will display the number of flash drives that failed and passed. 7. When Copy is complete the Compare portion will automatically begin. The LCD will display the status of the copying process. 8. When Compare is complete the display will show the total, and the number that pass and fail. N\fte: Whe\f Copy+Compare i\is i\f process the Gre\ie\f LED o\f the fro\ft pa\fel is bli\fki\fg. Do \i\fot take out the dr\iive while it is work\ii\fg. Whe\f Copy+Compare is fi\fish\ied the Gree\f LED st\iays o\f (\fo bli\fki\fg).\i If a\f error occurs duri\fg \ithe process a Red L\iED will display. ESC OK C\fpy 450M 15% 0:32 68M ESC OK C\fmpare 925M 15% 0:18 226M ESC OK T\ftal: 11/0 Pass 11 Fa\bl 0 ESC OK ENT ESC ENT ESC ENT ESC ENT ESCT\ftal OK: 5 OK: \C5 NG: 0 1:03 OK: 5 NG: 0
www.aleratec.com16 Ma\bn Menu Asynchronous Copy+Compare Asynchronous Copy+Compare is used only when the source content is the same as or less than the system buffer (256MB). With the source content read into the systems buffer you can copy and compare flash drives continuously by taking out the drive which has finished its Copy+Repair cycle, and replacing it with another blank. This process is repeated until the Copy+Compare job is complete. 1. Load the source flash drive into the USB Duplicator. Use the UP or DOWN arrow to scroll through the menu until Copy+Compare is displayed on the LCD screen. 2. Press the OK button on the display panel. The USB Duplicator will start to read the source content into the system’s buffer and immediately start copying any loaded target USB flash drives. 3. Load the blank target flash drives into the USB Duplicator. The LCD will display the number of blank media loaded and copying. N\fte: Whe\f copyi\fg is i\f pr\iocess the Gree\f LED\i o\f the fro\ft pa\fel is\i bli\fki\fg. Do \fot take\i out the drive while\i it is copyi\fg. Whe\f \icopyi\fg is fi\fished the Gree\f LE\iD stays o\f (\fo bli\fk\ii\fg). If a\f error occ\iurs duri\fg the copy process a \iRed LED will display\i. USB(58M) 450M Read\bng...ESC OK ESC OK USB Dupl\bcat\fr 3. C\fpy+C\fmpare Pass: 0 W\frk\bng Fa\bl: 0 3ESC OK ENT ESC ENT ESC ENT ESC
www.aleratec.com17 Us\bng the USB Dupl\bc\Cat\fr Asynchronous Copy+Compare - continued 4. If the Copy fails, the LCD will display the number of flash drives that failed and passed. N\fte: Duri\fg Asy\fchro\fous Copyi\fg \iyou ca\f use the UP a\fd DOWN arrow keys to chec\ik each flash drives \icopyi\fg status. 5. When Copy is complete the Compare portion will automatically begin. The LCD will display the status of the copying process. 6. When Compare is complete the display will show the total, and the number that pass and fail. When Copy+Compare is finished with any of the target drives you can take out the finished drive and put another blank flash drive for Copy+Compare. N\fte: Whe\f Copy+Compare i\is i\f process the Gre\ie\f LED o\f the fro\ft pa\fel is bli\fki\fg. Do \i\fot take out the dr\iive while it is work\ii\fg. Whe\f Copy+Compare is fi\fish\ied the Gree\f LED st\iays o\f (\fo bli\fki\fg).\i If a\f error occurs duri\fg \ithe process a Red L\iED will display. Pass: 5 W\frk\bng Fa\bl: 0 2ESC OK ESC OK C\fmpare 925M 15% 0:18 226M ESC OK ENT ESC ENT ESC ENT ESCT\ftal OK: 5 OK: \C5 NG: 0 1:03 OK: 5 NG: 0
www.aleratec.com18 Us\bng the USB Dupl\bc\Cat\fr Ma\bn Menu Capacity Check This function will check the capacity of each flash drive inserted. When finished the following screen will appear. Using the UP and DOWN arrows, you can scroll thru each drive loaded to display capacity. I\fformatio\f This function includes 2 subfunctions. These are: 5.1 USB Inf\f 5.2 System Inf\f USB Dupl\bcat\fr 5. Inf\frmat\b\fn OK ESC ESC OK Pass: 12 Cap\Cac\bty Fa\bl: 0 \C 0 ESC OK [#01] SIZE: 953M Capac\bty OK ENT ESC ENT ESC
www.aleratec.com19 Us\bng the USB Dupl\bc\Cat\fr 5.1 USB Info. USB Info is a function that displays the USB flash drives basic information such as flash type, content size, and available space. 1. Use UP or DOWN arrow to scroll through the menu until Information is displayed on the LCD screen. Press the OK button to select or press ESC to go to the next setting. 2. Press OK to get USB Info. You can scroll through each drive with the arrow keys. Press ESC when finished. The LCD will display the following status: 5.2 System Info. 1. Use UP or DOWN arrow to scroll through the menu until System Information is displayed on the LCD screen. 2. Press the DOWN arrow to get to System Info. and press OK. Press ESC twice to return to the Main Menu. ESC OK 5. Inf\frmat\b\fn 1. USB Inf\f ESC OK 01 USB 953M FAT 16 925M ESC OK 5. Inf\frmat\b\fn 2. System Inf\f
www.aleratec.com20 Us\bng the USB Dupl\bc\Cat\fr Ma\bn Menu Utility The main menu Utility function has 6 subfunctions. These are: 6.1 F\frmat FAT 6.2 Measure Speed USB Dupl\bcat\fr 6. Ut\bl\bty OK ESC 6.3 Med\ba Check 6.4 Qu\bck Erase USB\C 6.5 Full Erase USB 6.6 System Update 6.7 Calc. Checksum
www.aleratec.com21 Us\bng the USB Dupl\bc\Cat\fr Ma\bn Menu 6.1 Format FAT This function is used to format flash drives with the duplicator. If the original format is FAT, then the format operation will not change the format, but will write over any data on the flash drive. If the format is not FAT (e.g. NTFS, Linux, or FAT multi-partition) the controller will check the capacity of the flash drive. If the capacity is greater than 2GB, it will automatically use FAT 32 format. If the capacity is less than 2GB, it will use FAT 16. 1. Load the flash drives into the USB Duplicator. Use the UP or DOWN arrow to scroll through the menu until Utility is displayed on the LCD screen. 2. Use the UP and DOWN arrow keys to check the status of any of the flash drives loaded in the machine. Drives inserted in the first port (source) will not be formatted. ESC OK USB Dupl\bcat\fr 6. Ut\bl\bty ESC OK D\f FORMAT C\fnfirm? ESC OK [Ut\bl\bty] 1. F\frmat FAT
www.aleratec.com22 Us\bng the USB Dupl\bc\Cat\fr 6.2 Measure Speed This function will measure the read and write speeds of drives loaded in the ports. 1. Load drives. Use UP or DOWN arrow to scroll through the menu until Utility is displayed on the LCD screen. Press the OK button to select or press ESC to go to the next setting. 2. Press OK and scroll to Measure Speed. The LCD will display the following status: 3. Use the UP and Down arrow keys to check each drive. 6.3 Media Check This function is used to check flash drives with the controller. There are 2 types of checks that can be performed. Safe and Normal. The area to be examined can be set for each check. 1. Load drives. Use UP or DOWN arrow to scroll through the menu until Utility is displayed on the LCD screen. Press the OK button to select or press ESC to go to the next setting. ESC OK USB Dupl\bcat\fr 6. Ut\bl\bty ESC OK [Ut\bl\bty] 2. Measure Speed ESC OK [#2] Read: 21.7MB Wr\bte: 10.7 MB Port positio\f ESC OK USB Dupl\bcat\fr 6. Ut\bl\bty
www.aleratec.com23 Us\bng the USB Dupl\bc\Cat\fr 2. Press OK and scroll to Media Check. The LCD will display the following status: 3. Use UP or DOWN arrow to scroll through the available options: 6.3.1 Safe Check This function will read all the data on the flash drive with no writing so as to preserve all of the data and format on the drive. Use the UP and Down arrow keys to check the results on all of the drives loaded. 6.3.2 Normal Check The controller will read and write in each area of the drive. If one of the areas cannot be written to or read, the display will show an error. Use the UP and Down arrow keys to check the results on all of the drives loaded. N\fte: All data a\fd formats\i will be destroyed \iwith the Normal Che\ick. 6.3.3 Setup Range This function will adjust the percentage of the drive tested in the Safe and Normal Checks. Use the Up and Down arrow keys to change the percentage tested. ESC OK [Ut\bl\bty] 3. Med\ba Check ESC OK [Med\ba Check] 1. Safe 100% (perce\ftage of drive \itested) ESC OK [Med\ba Check] 2. N\frmal 100% (perce\ftage of drive \itested) ESC OK [Med\ba Check] 3. Setup Range
www.aleratec.com24 Us\bng the USB Dupl\bc\Cat\fr 6.4 Quick Erase USB Quick Erase USB is a function that can quickly erase the target USB flash drive. N\fte: The Quick Erase USB\i fu\fctio\f will o\fly er\iase the FAT table i\fdex of each target flash\i drives. 1. Use UP or DOWN arrow to scroll through the menu until Utility is displayed on the LCD screen. Press the OK button to select or press ESC to go to the next setting. 2. Press OK and scroll to Quick Erase USB. The LCD will display the following status: 3. Press OK to select. The LCD will display the following status: Press OK for Yes or ESC for No. 4. LCD display will show the following screen when finished. N\fte: This fu\fctio\f will era\ise the flash drive’s data co\fte\ft. It \iwill \fot erase the flash driv\ie’s FAT 16/32 format. If th\ie format of the targ\iet drive is \fot FAT 16/32\b the Quick Er\iase wo\f’t execute. ESC OK USB Dupl\bcat\fr 6. Ut\bl\bty ESC OK 6. Ut\bl\bty 4. Qu\bck Erase USB ESC OK D\f Erase All C\fnfirm? ESC OK Pass: 2 W\frk\bng Fa\bl: 0 0