Home > Aleratec > Hard Disk > Aleratec 111 HDD Copy Cruiser IDESATA 11 HDD Duplicator and 12 HDD Sanitizer User Guide

Aleratec 111 HDD Copy Cruiser IDESATA 11 HDD Duplicator and 12 HDD Sanitizer User Guide

    Download as PDF Print this page Share this page

    Have a look at the manual Aleratec 111 HDD Copy Cruiser IDESATA 11 HDD Duplicator and 12 HDD Sanitizer User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 61 Aleratec manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							www.aleratec.com35
    Using the 1:11 HDD Copy Cruiser IDE/SATA 
    Main Menu
    Setup
    Setup:	Boot	Time	Delay
    If HDD can not be detected during duplicate controller boot up, this function 
    can adjust the timer. 
    1. Use the arrow buttons (or) to select “Setup”. The following screen 
    will be displayed. 
    2. Press the arrow buttons () to scroll to “Boot Time Delay”. The 
    following screen will be displayed. 
    3. Press ENT to display the current configuration setting (0-99 sec).
    4. Use the arrow buttons () to change the setting. Once you change a 
    default, remember to press ENT to save it.
    ENTESC
    
    
    10. Setup
    ENTESC
    
    
    10-12. SetupBoot Time Delay
    ENTESC
    
    
    Boot Time Delay5 Sec  
    						
    							www.aleratec.com36
    Using the 1:11 HDD Copy Cruiser IDE/SATA
    Main Menu
    Setup
    Setup:	Quick	Compare
    If target HDD has too many errors, the duplicate controller will ignore it and 
    keep comparing other target HDDs. 
    1. Use the arrow buttons (or) to select “Setup”. The following screen 
    will be displayed. 
    2. Press the arrow buttons () to scroll to “Quick Compare”. The 
    following screen will be displayed. 
    3. Press ENT to display the current configuration setting (Off or 1 Byte - 
    100 MBytes).
    4. Use the arrow buttons () to change the setting. Once you change a 
    default, remember to press ENT to save it.
    ENTESC
    
    
    10. Setup
    ENTESC
    
    
    10-13. SetupQuick Compare
    ENTESC
    
    
    Quick CompareOff  
    						
    							www.aleratec.com37
    Using the 1:11 HDD Copy Cruiser IDE/SATA 
    Main Menu
    Advanced Setup
    The “Adv Setup” menu contains additional configuration options for the 1:11 HDD 
    Copy Cruiser IDE/SATA.  
    1. Press and hold the ESC	button for 3 seconds to enter Adv Setup. The following 
    screen will be displayed.
    Note: After changing any of the configuration options, you must 
    press ENT to accept the change. Once all changes are complete, 
    press ESC to exit the Adv Setup menu. The following screen will be 
    displayed. 
    2. When the configuration changes have been saved, the following screen will be 
    shown. 
    ENTESC
    
    
    11. Adv Setup
    ENTESC
    
    
    Saving Config...Please Wati...
    ENTESC
    
    
    11. Adv Setup  
    						
    							www.aleratec.com38
    Using the 1:11 HDD Copy Cruiser IDE/SATA 
    Main Menu
    Adv Setup
    Adv	Setup:	Read	Error	Skip
    This function can be enabled to ignore any error that occurs during copying.  
    By default, the 1:11 HDD Copy Cruiser IDE/SATA will halt the copy operation 
    when it encounters an unreadable area of the source hard disk and display an 
    error. Enabling this option will ignore any bad sectors on the source hard drive 
    by skipping over them.  
    Warning: Setting this function to “On” may result in corrupt data on 
    copied hard drives. 
    1. Press and hold ESC for about 3 seconds to access the “Adv Setup” menu. 
    The following screen will be displayed.
    2. Use the arrow buttons (or) to scroll to “Read Error Skip”. The 
    following screen will be displayed. 
    3. Press ENT to display the current configuration setting. The default setting 
    is “Off”. 
    4. Press the arrow buttons (or) to toggle the option “On” or “Off”. After 
    changing a setting, remember to press ENT to save it.
    ENTESC
    
    
    11. Adv Setup
    ENTESC
    
    
    Read Error SkipOff
    ENTESC
    
    
    11-01. Adv SetupRead Error Skip  
    						
    							www.aleratec.com39
    Using the 1:11 HDD Copy Cruiser IDE/SATA 
    Main Menu
    Adv Setup
    Adv	Setup:	Update	Firmware
    This function is used to update the 1:11 HDD Copy Cruiser IDE/SATA firmware to 
    a later version. 
    Note: Firmware updates are available from Aleratec technical support.    
    1.a CD method 
    Open the case of the 1:11 HDD Copy Cruiser IDE/SATA . Disconnect the SATA 
    cable from the blue connector on the controller board.  Connect a SATA DVD/CD 
    drive (not included) to the blue connector.  Place the firmware CD in the DVD/CD 
    drive. 
    1.b Hard Drive method 
    Format a hard drive and create a single partition to the smallest capacity 
    allowable. Copy the firmware file into the root directory of this partition. 
    2. Power on the 1:11 HDD Copy Cruiser IDE/SATA. Once the system has 
    completed its startup process, press and hold the ESC button for about 3 
    seconds to access “Adv Setup”. The following screen will be displayed. 
    3. Use the arrow buttons () to select “Update Firmware”, and then press 
    ENT. The system will begin scanning for a new firmware version. If found, 
    screens similar to the following will be displayed.
    4. Press ENT to begin the firmware update. If the upgrade is successful, the 
    system will restart automatically. 
    ENTESC
    
    
    11. Adv Setup
    Searching F/W...Please Wait...
    Update F/W  1.04NTo *.** Yes  
    						
    							www.aleratec.com40
    Using the 1:11 HDD Copy Cruiser IDE/SATA 
    Main Menu
    Adv Setup
    Adv	Setup:	Compare	Firmware
    This function is used to compare the firmware version currently installed with 
    one on a DVD/CD disc. 
    Note: Use “Compare Firmware” after updating the firmware from 
    e-mail or from the Aleratec web site. This function is used after 
    performing a firmware update on the 1:11 HDD Copy Cruiser IDE/
    SATA. 
    1. Press and hold ESC for about three seconds to access the “Adv Setup” 
    menu. The following screen will be displayed. 
    2. Use the scroll button (or) select “Compare Firmware”. The following 
    screen will be displayed. 
    3. Press ENT to begin comparison. The following screen will be displayed.
    Note: The message “Last update F/W” indicates that the 
    installed firmware revision matches that on the DVD/CD disc. 
    ENTESC
    
    
    11. Adv Setup
    ENTESC
    
    
    11-03. Adv SetupCompare Firmware
    Searching F/W...Please Wait...
    Last update F/WOK!  
    						
    							www.aleratec.com41
    Using the 1:11 HDD Copy Cruiser IDE/SATA 
    Main Menu
    Adv Setup
    Adv	Setup:	Quick	Erase	HDD
    This function is used to erase the data of a hard drive quickly. 
    Warning: Backup any important data before using this function. 
    1. Press and hold ESC for about three seconds to access the “Adv Setup” 
    menu. The following screen will be displayed. 
    2. Use the arrow buttons (or) to select “Quick Erase HDD”. The 
    following screen will be displayed.
    3. Press ENT, and then use the arrow keys () to select a hard drive to 
    erase. An example is shown below. 
    4. Press ENT, and you will be prompted whether you wish to proceed. Use 
    the arrow keys () to select “Yes” or “No”. The following screen will 
    be displayed. 
    5. Press ENT and the Quick Erase will begin. Once complete the following 
    information will be displayed. 
    ESC
    
    
    11. Adv SetupENT
    ESC
    
    
    11-04. Adv SetupQuick Erase HDDENT
    ESC
    
    
    1 Target  CH:1HDS721616PLA380ENT
    ESC
    
    
    All data will be lost, erase? NoENT
    Erasing TargetPlease Wait...
    The Selected HDDErase Finished  
    						
    							www.aleratec.com42
    Using the 1:11 HDD Copy Cruiser IDE/SATA 
    Main Menu
    Adv Setup
    Adv	Setup:	Full	Erase	HDD
    This function is used to fully erase all data on the HDD. 
    Warning: Backup any important data before using this function. 
    1. Press and hold ESC for about three seconds to access the “Adv Setup” 
    menu. The following screen will be displayed. 
    2. Use the arrow buttons (or) to select “Full Erase HDD”. The following 
    screen will be displayed.
    3. Press ENT, and then use the arrow keys () to select a hard drive to 
    erase. An example is shown below. 
    4. Press ENT, and you will be prompted whether you wish to proceed. Use 
    the arrow keys () to select “Yes” or “No”.
    5. Select “Yes”, press ENT and the Full Erase will begin. Once complete the 
    following information will be displayed. 
    ESC
    
    
    11. Adv SetupENT
    ESC
    
    
    11-05. Adv SetupFull Erase HDDENT
    ESC
    
    
    Full Erase HDDAllENT
    ESC
    
    
    All data will be lost, erase? NoENT
    Erasing TargetPlease Wait...
    The Selected HDDErase Finished  
    						
    							www.aleratec.com43
    Using the 1:11 HDD Copy Cruiser IDE/SATA 
    Main Menu
    Adv Setup
    Adv	Setup:	H/W	Diagnostic
    This function is used to test various components of the 1:11 HDD Copy Cruiser 
    IDE/SATA. 
    1. Press and hold ESC for about three seconds to access the “Adv Setup” 
    menu. The following screen will be displayed. 
    2. Use the arrow buttons (or) to select “H/W Diagnostic”. The following 
    screen will be displayed. 
    3. Press ENT to begin the diagnostic tests. The following tests will be 
    performed: Button Test, Self-Test of SDRAM, Hardware Connection Test, 
    and Flash Test. Follow the on screen prompts to complete each test. All 
    test results will be shown in the display panel.  
    4. When all tests are complete the following information will be displayed. 
    ESC
    
    
    11. Adv SetupENT
    ESC
    
    
    11-06. Adv SetupH/W DiagnosticENT
    ESC
    
    
    Test FinishedENT
    
    LCD Test StartButton Test →
    
    SDRAM Test:8192Kbytes OK
    
    Test IDE 0/1OKFlash Test: OK
    
    Test finished  
    						
    							www.aleratec.com44
    Using the 1:11 HDD Copy Cruiser IDE/SATA 
    Main Menu
    Adv Setup
    Adv	Setup:	Load	Default
    This function is used to restore all factory settings of the 1:11 HDD Copy 
    Cruiser IDE/SATA back to their original defaults. 
    1. Press and hold ESC for about three seconds to access the “Adv Setup” 
    menu. The following screen will be displayed. 
    2. Use the arrow buttons (or) to select “Load Default”. The following 
    screen will be displayed. 
    3. Press ENT to proceed to the following screen:
    Press ENT to confirm loading defaults, or press ESC to cancel.
    4. When all settings are restored to their original defaults the following 
    information will be displayed. 
    ESC
    
    
    11. Adv SetupENT
    ESC
    
    
    11-07. Adv SetupLoad DefaultENT
    ESC
    
    
    Load DefaultConfig? YesENT
    ESC
    
    
    Load DefaultOKENT  
    						
    All Aleratec manuals Comments (0)

    Related Manuals for Aleratec 111 HDD Copy Cruiser IDESATA 11 HDD Duplicator and 12 HDD Sanitizer User Guide