Home
>
Albrecht
>
Communications receiver
>
Albrecht AE77H Programmable Hand-Held-Scanner Operating Guide
Albrecht AE77H Programmable Hand-Held-Scanner Operating Guide
Here you can view all the pages of manual Albrecht AE77H Programmable Hand-Held-Scanner Operating Guide. The Albrecht manuals for Communications receiver are available online for free. You can easily download all the documents as PDF.
Page 11
11 Restore a Locked Out Channel 1. Press . Locking a Channel While ScanningIf the scanner keeps stopping on a particular channel due to noise or too frequent transmissions, you may want to keep that channel from scanning. 1. Wait until the scanner stops at thechannel. 3. The scanner immediately resumes scanning because the locked out channel is no longer in the scanning sequence. Lockout Tips•To quickly lockout a series of channels, start with the lowest number channel. For example, if you are locking...
Page 12
12 Restore All Locked-out Channels 1. Press . 2. Press and hold /L/O for abouttwo seconds. You will hear two beeps when all the channels have been restored. Priority Scan When priority scan is turned on, your scanner checks the priority channel every two seconds for activity. If a signal is present on the priority channel, your scanner monitors the channel until the transmission ends, then resumes normal scanning. You can designate any of the 100 available channels as your priority channel. Changing the...
Page 13
132. Enter lower limit of the search band. a) Enter the frequency number. b) Then press . c) Then press /LIMIT. BAND Searching Band SearchThe AE 77H has 6 factory- Preprogrammed Search Bands. You can search any of these Bands to find desired frequencies if you do not have a Frequency Directory handy, or if new stations have been added since the Directory was published. 1. Press and hold /LIMIT to enter the Band Search Mode. Then the upper and lower limits of the band currently selected are...
Page 14
14 3. Enter upper limit of the search band. a) Enter the frequency number. b) Then press . Direct SearchYou can search by using or when you listen to a channel. 1. Press . 2. Select a channel a) Enter the channel number. b) Then press . — OR — Enter the frequency. 3. Press or to start seaching. 4. Press /LIMIT at any time to stop the search on a frequency. Press /LIMIT to resume searching. BAND BAND 4. Either press or to begin your search. 5. Press /LIMIT at any time to stop the search on a...
Page 15
2. Press to move to the next higher frequency 3. Press to move down to the previous frequency. 15 Search Hold Feature1. Press /LIMIT at anytime to stop the search.BAND 5. When search is stopped, you canpress or to move up or down 1 frequency step. Note:The search continues toward either the upper or lower search limit, depending on which direction key ( or ) was pressed last. 4. Press /LIMIT to resume searching.BAND Channel SkipIf a particular channel continues to interrupt search scanning, it...
Page 16
16 1. Press /MON/ CLR to store thedisplayed frequency in the MONITOR MEMORY. 2. Either press or to begin your search. 3. Press /PROG and enter the channel number, then press /PROG again. STEP STEP Storing Search FrequenciesYou can quickly store any frequency you find during search. 4. Press /MON/ CLR and number key to select the MONITOR MEMORY. — OR — /MON/ CLR repeatedly. 5. Press to store the frequency in the channel you selected. Note:You can program 10 MONITOR MEMORIES. Repeat steps 2 through...
Page 17
17 Care and Maintenance General Use•Turn the scanner off before disconnecting the power or replacing the batteries. •Always write down the programmed frequencies in the event of memory loss. •If memory is lost, simply reprogram each channel. The display shows 000.0000 in all channels when there has been a memory loss. •Always press each button firmly until you hear the entry tone for that key entry. Location•Do not use the scanner in high- moisture environments such as the kitchen or bathroom. •Avoid...
Page 18
18 Troubleshooting If your AE 77 H is not performing properl y, try the following steps. Problem Suggestion Scanner won ’t work. 1. Check the connections at both ends of the AC Adapter. 2. Turn on the wall switch of your room. You could be using an outlet controlled by the wall switch. 3. Check to see the batteries are installed followed by the + and – symbols. Improper reception. 1. Check the antenna connection or move and reposition the antenna. 2. Move the scanner. 3. You may be in a remote area...
Page 19
19 Specifications Declaration of Conformity Channels: 100 Frequency Bands (European version see annex on last page):No. RANGE (MHz) MODE STEP (kHz) (1) 66.0000 - 88 .0000 FM 5 (2) 108.0000 - 136.9750 AM 12.5 or (2) 108.0000 - 136.9916 AM 8.33 (3) 137.0000 - 143.9950 FM 5 (4) 144.0000 - 145.9875 FM 12.5 (5) 146.0000 - 174.0000 FM 5 (6) 406.0000 - 512.0000 FM 12.5 Operating temperature :– 20 °C to +60 °C Scan rate:17 channels per second Search rate:20 steps per second Scan delay:2 seconds Audio...
Page 20
CE Konformitätserklärung/ Declaration of Conformity Hiermit wird erklärt, daß unser Produkt / herewith we declare that\ our product Empfangsgerät für Funkdienste (Scanner) AE 77 H den folgenden europäischen Normen entspricht: / is in conformity to following European Standards EU -Richtlinien / EU directives 73/23/EEC (LVD); 89/336 EEC (EMC) and 99/5/EEC (R&TTE) EN 301 489-1, EN 301 489-5, EN 301 489-15 (EMC) EN 300 086-2 (PMR Radio) EN 301 783-2 (Amateur...