Alarm Lock PL3000 Programming Instructions User Manual

11 
WIRING 
See the Installation Manual for more information. 
Batteries: 
Use only 1.5 volt Duracell Alkaline size-AA batteries. 
External Power: 
Red / Black wires - External 7.5 VDC Power Source must 
be used for operation without batteries. 
Remote Input: 
White / White wires - Wire a Normally Open Contact to 
wires (white and white).  Momentarily close to allow 
PL3000 lock to unlock.  NOTE:  Remote Input is enabled 
from the factory.   
Relay: 
COM-Blue / NO-Yellow / NC-Green 
Erase Memory Leads:...

12 
Quick Start 
The following Quick Start guide outlines how to get your lock up and running quickly.  Function Cards will be enrolled, there-
fore before starting, label the 9 proximity cards (provided) with the numbers 1 through 9, and have these labeled cards at 
hand before starting.  If you do not wish to enroll Function Cards (and wish to only program your lock via DL-Windows or via 
an AL-DTM), proceed to First Time Start Up--Using DL-Windows Only (page 13). 
 
First Time Start Up--Using Function...

13 
Quick Start (cont’d) 
Delete ProxCards® 
When deleting enrolled proximity cards with Function Card #4, you must have possession of the card to be deleted.  If 
you wish to delete cards that are NOT in your possession, you must do so either via DL-Windows or a pre-programmed 
AL-DTM module.  WARNING:  If using Function Cards only (without DL-Windows) the only way to delete a previously 
enrolled proximity card that is not in your possession is to clear all lock programming.  See procedure ERASE ALL...

14 
Function Card 
Number Description See 
Page 
Card #1 Initiates PC communications (User 298). 15 
Card #2 Initiates AL-DTM communications (User 299). 16 
Card #3 Initiates entry of new proximity cards starting at User 301 (and 
ending at User 2000). 18 
Card #4 Initiates removal of next presented proximity card. 19 
Card #5 Toggles Passage Mode (Door is unlocked---all Users are allowed 
free access through the door).   20 
Card #6 Initiates AL-IR1 printing with Time, Date, Version Number and Au-
dit...

15 
Function Card #1 
IMPORTANT NOTE:   
When programming is sent from DL-Windows (or an AL-DTM) to the lock, Function Cards 1, 2, 8, and 9 will be overwritten with 
the existing data in DL-Windows for the User Locations 298, 299, 297 and 300, respectively.  Therefore, to continue to use 
Function Cards 1, 2, 8 and 9 that were enrolled at startup with DL-Windows, be sure to enroll those same Function Cards 1, 
2, 8 and 9 used at startup into the correct locations within DL-Windows.  For complete...

16 
Function Card #2 
Initiates AL-DTM Communications (User 299) 
The AL-DTM is used to transfer Lock Programs (and other data) between DL-Windows and PL3000 locks.  When com-
puters cannot be transported or when electrical power is not available, the hand-held AL-DTM acts as a go-between--it 
allows the transfer of lock data from your PC (through the AL-DTM) to the lock, or in reverse (from the lock through the 
AL-DTM back to your PC).  Requires an AL-PCI2 cable when transferring from your PC to the...

17 
Function Card #2 (contd) 
 
IMPORTANT NOTE:   
When programming is sent from DL-W indows (or an AL-DTM) to the lock, Function Cards 1, 2, 8, and 9 will be overwritten 
with the existing data in DL-Windows for the User Locations 298, 299, 297 and 300, respectively.  Therefore, to continue to 
use Function Cards 1, 2, 8 and 9 that were enrolled at startup with DL-Windows, be sure to enroll those same Function 
Cards 1, 2, 8 and 9 used at startup into the correct locations within DL-Windows.  For...

18 
Function Card #3 
IMPORTANT NOTE:   
Function Cards 3 through 7 are not recognized by DL-Windows.  Therefore, DL-Windows will not send the data for 
Function Cards 3-7 to the AL-DTM, nor will the AL-DTM be able to send this Function Card data to the PL3000 
lock.  Accordingly, Function Cards are designed to be used for limited-use installations where DL-Windows will not 
be used.  When User Numbers are printed in the Audit log, Function Cards 3-7 will appear as User Numbers 
2003-2007. 
Initiates...

19 
Function Card #4 
IMPORTANT NOTE:   
Function Cards 3 through 7 are not recognized by DL-Windows.  Therefore, DL-Windows will not send the data for 
Function Cards 3-7 to the AL-DTM, nor will the AL-DTM be able to send this Function Card data to the PL3000 
lock.  Accordingly, Function Cards are designed to be used for limited-use installations where DL-Windows will not 
be used.  When User Numbers are printed in the Audit log, Function Cards 3-7 will appear as User Numbers 
2003-2007. 
Initiates...

20 
Function Card #5 
IMPORTANT NOTE:   
Function Cards 3 through 7 are not recognized by DL-Windows.  Therefore, DL-Windows will not send the data for 
Function Cards 3-7 to the AL-DTM, nor will the AL-DTM be able to send this Function Card data to the PL3000 
lock.  Accordingly, Function Cards are designed to be used for limited-use installations where DL-Windows will not 
be used.  When User Numbers are printed in the Audit log, Function Cards 3-7 will appear as User Numbers 
2003-2007. 
Toggles...