Home
>
Alarm Lock
>
Alarm Lock
>
Alarm Lock KEYPAD A100WP SEALED ENVIRONMENT WIRING PROGRAMMING INSTRUCTIONS User Manual
Alarm Lock KEYPAD A100WP SEALED ENVIRONMENT WIRING PROGRAMMING INSTRUCTIONS User Manual
Have a look at the manual Alarm Lock KEYPAD A100WP SEALED ENVIRONMENT WIRING PROGRAMMING INSTRUCTIONS User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 84 Alarm Lock manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
1 A-100WP SEALED ENVIRONMENT KEYPAD WIRING & PROGRAMMING INSTRUCTIONS WI1496 12/06 GENERAL DESCRIPTION The A-100WP is a self-contained access control keypad de- signed for the harshest outdoor environments. Its heavy stainless steel enclosure and metal keypad buttons also make it extremely vandal resistant. The A-100WP operates up to three outputs (two relays and 1 open-collector transis- tor) and can be used to trigger a door strike, an electromag- netic door lock, or any other relay-activated device. Pro- gramming is performed manually at the keypad, allowing up to 150 individual Users, each with their unique User Codes. The A-100 Series includes the indoor stainless steel A-100 (see WI1495) and the waterproof A-100IMWP (see WI1497) mullion keypad with illuminated keys. In a typical application, the A-100WP will energize one or both relays upon the keypad entry of a valid User Code. Outputs 1 and 2 are two relays of the three contact Form C type, and Output 3 is an open collector transistor (terminal labeled OC) that switches on (closes with the ground ter- minal) when energized. The length of time the outputs are energized (their activation duration) can be programmed to between 1 and 99 seconds. A Request-to-Exit button will momentarily short Output 1 by wiring terminals M and P1 using a normally-open momentary-close switch. To program the keypad functions you must first perform the initial startup procedure, then enter Program Mode by press- ing the Master Code at the keypad. Once in Program Mode, all system functions can be accessed and programmed. Exit Program Mode to put the keypad (with its new programming) into use. A-100WP Wiring Table Terminal Markings Description + + 12V or 24V AC/DC Input – – Ground M Request to Exit Input P1 Request to Exit Input NO Relay 1 Normally Open C1 Relay 1 Common NC Relay 1 Normally Closed NO Relay 2 Normally Open C2 Relay 2 Common NC Relay 2 Normally Closed OC Open Collector Output S1 Tamper SW Output S2 Tamper SW Output + 12V or 24V AC/DC Input – Ground Common Relay 2 Request to Exit Input Request to Exit Input Normally Open Relay 1 Common Relay 1 Normally Closed Relay 1 Normally Open Relay 2 Normally Closed Relay 2 NC NO NO C1 C2 P1 + – M NC A-100WP Keypad SPECIFICATIONS •12 to 24VDC (polarized) or 12 to 24VAC voltage input •Output 1: 5A/250VAC relay •Output 2: 5A/250VAC relay •Output 3: 250mA open collector •Capacity of 150 User Codes of 3 to 6 digits •Output activation duration programmable from 01-99 seconds (program 00 to select toggle mode) •All programming stored in non-volatile EEPROM memory •12 Braille keypad keys •Orange LED Keypress feedback •Output #1 relay activation duration programmable per user code •Tamper switch output terminals (S1 - S2) on PCB •Sounder beeps can be activated or deactivated for user code entries •Operating Temperature: -13°F to 131°F -25°C to +55°C •Dimensions (WxHxD): 4 x 4¾ x 2 10.1cm x 12cm x 5cm •Operating Voltage: 12VDC to 28VDC 10VAC to 26 VAC •Maximum Current Draw: 12VDC: 15mA (Standby) 54mA (Active) 24VDC: 22mA (Standby) 67mA (Active) 12VAC: 32mA (Standby) 108mA (Active) 24VAC: 54mA (Standby) 129mA (Active) S2 S1 OC Open Collector Output Tamper SW Output Tamper SW Output 345 Bayview Avenue Amityville, New York 11701 For Sales and Repairs 1-800-ALA-LOCK For Technical Service 1-800-645-9440 Publicly traded on NASDAQ Symbol: NSSC © ALARM LOCK 2006
2 GETTING STARTED First Time Startup--Self-Test After you unpack the lock from its factory packaging, you must perform the initial startup procedure (outlined be- low). For keypads already in use, this startup procedure can also be used to erase all existing keypad program- ming and return the keypad back to its original out of box factory default condition. 1. Install the jumper located on the back of the key- pad. 2. Apply power (12-24VDC polarized or 12-24VAC) to the power input terminals. •Orange LED blinks once 3. Press 7890#123456* (note that keys are silent when pressed). •Red LED turns ON •Orange LED turns ON •Green LED turns ON •Green LED turns OFF •Each Output 1,2 & 3 activates for 1½ seconds •Orange LED turns OFF •Sounder beeps twice (memory resets and default values enabled) 4. Close the Request to Exit button (short terminals M and P1). •Red LED blinks 5. Remove the jumper on the back of the keypad. •Sounder beeps once 6. Remove power to the power input terminals. 7. Apply power to the power input terminals. •Sounder beeps once If the keypad encounters a problem while memory is re- setting at step 3, the sounder will beep continuously until the jumper is removed and the procedure is repeated at step 1. The factory default values are detailed in the sec- tion below. Default Values No pre-configured user codes exist for new out of the box keypads. Other default values include: User Code length 4 digits Maximum Delay Between Key Presses 10 seconds Auto Exit Program Mode 120 seconds Factory Default Master Code 1234 Output Activation Duration 5 seconds Sounder Always ON First Key Press Activates Output 3 Inactive Enter Program Mode The keypad software has only two modes--Normal Mode and Program Mode. When you want to make changes to the keypad (enter new User Codes, etc.), you enter Program Mode. When you finish programming and wish to put the keypad into use, you exit Program Mode to enter Normal Mode. •Enter Program Mode: Press 55#1234*. Enter Program Mode by pressing 55#, then press the Master Code of the lock that was set at the factory ( 1234), followed by the * key (the orange LED lights and the sounder beeps twice). The factory Master Code (1234) is basically a se- cret passcode that allows you to enter Program Mode. But since all keypads leave the factory with this same Master Code, the factory Master Code is therefore not very secret--and should be changed to your own per- sonal Master Code. This way, only YOU can enter Pro- gram Mode and make changes to the keypad program- ming. Change Factory Master Code Although the factory Master Code can be changed at any time, for highest security, follow the procedure below: Think of a new four-digit numeric Master Code and either commit it to memory or write it here: ___ ___ ___ ___. Note: Only numbers 0 through 9 are valid digits for either User Codes or the Master Code. Keys * or # are not allowed. In addition, the Master Code and all User Codes must always be the same number of digits in length (3-6 digits allowed). Therefore, if you enter Program Mode and change this Code Length using Function 30, you must then remain in Program Mode and change the Master Code to conform to the new Code Length. At this point, however, we recommend you do not change the Code Length unless you are an advanced user. 1. If not in already, enter Program Mode (press 55#1234*). •Orange LED lights - sounder beeps twice. 2. Press 31# •Green LED blinks once - sounder beeps once. 3. Press new 4-digit Master Code and press #. •Green LED blinks once - sounder beeps once. 4. Re-press new 4-digit Master Code and press #*. •Green LED lights / sounder beeps for 1 second indi- cating the Master Code was changed successfully. The keypad remains in Program Mode while the orange LED remains lit. Note: The keypad will automatically exit Program Mode if no keys are pressed within 120 seconds (2 minutes). Adding User Codes User Codes are 3-6 digit numbers the User presses into the keypad keys to activate one or more Outputs. The A- 100WP keypad can hold up to 150 User Codes in its memory, thus allowing up to 150 people to possess their own individual User Codes. The keypad memory associ- ates each User Code with a 3-digit User Number listed from 000 to 149. Therefore, when adding new User Codes, you must also select a 3-digit User Number be- tween 000 and 149 that will be associated (linked) with the new User Code. As with the Master Code, only num- bers zero through 9 are valid digits for User Codes (keys * or # are not allowed) and each User Code must be unique. 1. If not in already, enter Program Mode.
3 •Orange LED lights - sounder beeps twice. 2. Press 32# •Green LED blinks once - sounder beeps once. 3. Press new 3-digit User Number and press #. •Green LED blinks once - sounder beeps once. 4. Press new 4-digit User Code and press #. •Green LED blinks once - sounder beeps once. 5. Re-press new 4-digit User Code and press #*. •Green LED lights / sounder beeps for 1 second indi- cating the User Code was added successfully. Delete a User Code 1. If not in already, enter Program Mode. •Orange LED lights - sounder beeps twice. 2. Press 34# •Green LED blinks once - sounder beeps once. 3. Press the 3-digit User Number associated with the User Code you wish to delete and press #*. •Green LED lights / sounder beeps for 1 second indi- cating the User Code was deleted successfully. Exit Program Mode When you finish programming and wish to put the keypad into use, you exit Program Mode to enter Normal Mode as follows: •Exit Program Mode: Press *. The orange LED turns off, the sounder beeps twice and the red LED lights. Note: The keypad will automatically exit Program Mode if no keys are pressed within 120 sec- onds (2 minutes). Test the Keypad Be sure to test all User Codes. Keep in mind the follow- ing: •Valid User Codes must be followed by the star ( *) key •Master Code and User Codes must all be the same length •By default, a valid User Code always activates Output 1 unless Output selection is changed ALL PROGRAMMING FUNCTIONS Your keypad is designed to support several options and functions. Using the keypad, you can select the features you wish to activate, such as if the keypad sounder should be disabled or enabled or you wish to change the code length from 4 to 6 digits.. Each function is organized below by its function number, which is the first two digits pressed into the keypad when programming. To program, first enter Program Mode as follows: •Enter Program Mode: Press 55# [Master Code] *. When you finish programming and wish to put the key-pad into use, exit Program Mode to enter Normal Mode as follows: •Exit Program Mode: Press *. Note: The audible sounder and visual LED indicators are displayed in the text below as follows: [O2] = Orange LED lights and sounder beeps twice [G1] = Green LED lights and sounder beeps once [R2] = Red LED lights and sounder beeps twice Note: Every duration field is a two digit field. Master code is strictly reserved for entering Program Mode and cannot be used to activate an Output. 21 Output 1 Activation Duration Program time from 01 to 99 seconds. Program 00 to select latch mode where output remains activated by the entry of a valid User Code (until deactivated by the entry of a second valid User Code). Note: By default, a valid User Code always activates Output 1 unless Output selection is changed. Press: 21# [G1] ___ ___ #* [G1]. 22 Output 2 Activation Duration Program time from 01 to 99 seconds. Program 00 to select latch mode where output remains activated by the entry of a valid User Code (until deactivated by the entry of a second valid User Code). Press: 22# [G1] ___ ___ #* [G1]. 23 Output 3 Activation Duration Program time from 01 to 99 seconds. Program 00 to select latch mode where output remains activated by the entry of a valid User Code (until deactivated by the entry of a second valid User Code). Press: 23# [G1] ___ ___ #* [G1]. 30 Code Length Changes the number of required digits in all new User Codes and the existing Master Code. 3-6 digits are allowed, thus valid entries are 3, 4, 5 or 6. The factory default Code Length is 4. WARNING: When the Code Length is changed, all existing User Codes and the Master Code become in- valid. Because the Master Code and all User Codes must always be the same number of digits in length, if you change the Code Length with Function 30 you MUST remain in Program Mode and change the Mas- ter Code to conform to the new programmed Code Length. Press: 30# [G1] ___ #* [G1]. 31 Modify Master Code Changes existing Master Code. Note: The Master Code and all User Codes must always be the same number of digits in length. If changing the number of digits in the Master Code, you must first change the Code Length via Function 30 (to accommodate the new
4 number of digits in the new Master Code) and--without exiting Program Mode--change the Master Code via Function 31. Press: 31# [G1] (new MC) # [G1] (new MC) #* [G1]. Be sure to either commit the Master Code to memory or record it in a safe place. If the Master Code is ever lost, the keypad will need to be restarted using the First Time Startup procedure described on page 2. 32 Add (or Edit) a User Code Allows you to add a new or edit an existing User Code. User Codes are 3-6 digit numbers the User presses into the keypad keys to activate one or more Outputs. The A-100WP keypad can hold up to 150 User Codes in its memory, thus allowing up to 150 people to pos- sess their own individual User Codes. The keypad memory associates each User Code with a 3-digit User Number listed from 000 to 149. Therefore, when add- ing new User Codes, you must also select a 3-digit User Number between 000 and 149 that will be associ- ated (linked) with the new User Code. As with the Master Code, only numbers zero through 9 are valid digits for User Codes (keys * or # are not allowed) and each User Code must be unique. Programming requires entering the new User Code twice for confir- mation, as follows: Press: 32# [G1] (User Number) # [G1] (User Code) # [G1] (re-enter User Code) #* [G1]. 33 Add (or Edit) a User Code with Output 1 Duration Same as Function 32 plus the ability of the individual User Code to activate Output 1 for a specified duration (from 01 to 99 seconds). Program 00 to select latch mode where output remains activated by the entry of a valid User Code (until deactivated by the entry of a sec- ond valid User Code). Press: 33# [G1] (time 01-99) # [G1] (User Number) # [G1] (User Code) # [G1] (re-enter User Code) #* [G1]. 34 Delete User Code Overwrites specified User Number with vacant data, thus erasing the User Code from memory. Press: 34# [G1] (User Number) #* [G1]. 40 Reset Keypad Erase all existing keypad programming and return the keypad back to its original out of box factory default condition Press: 40# [G1] 12345# [G1] 12345#* [G1]. 52 Add (or Edit) a User Code with Output Activation Same as Function 32 plus the ability of the individual User Code to activate the specified Output(s). Press: 52# [G1] (2-digits*) # [G1] (User Number) # [G1] (User Code) # [G1] (re-enter User Code) #* [G1]. *Some examples of the 2-digits field: •press 12 to activate Outputs 1 and 2 •press 23 to activate Outputs 2 and 3 •press 13 to activate Outputs 1 and 3 •press 02 to activate Output 2 only •press 10 to activate Output 1 only ...etc. Note: If Function 70 (Output 3 Activates on First Keypress) is enabled, Output 3 cannot be included in the choices offered by Function 52. 60 Sounder Beeps Activate sounder beeping or deactivate when pressing User Codes only. Always ON Press: 60# [G1] 1#* [G1]. OFF for User Codes: 60# [G1] 0#* [G1]. Sounder factory default is Always ON. 70 Output 3 Activates on First Keypress Enable Output 3 to activate upon any first keypress when in Normal Mode (such as the first keypress when entering a User Code). Output 3 is a 250mA open collector transistor output. Function 70 can be used for many purposes, such as to trigger a surveil- lance camera to record all activity at the keypad. In addition, Output 3 is silent, therefore Users will be un- aware when Output 3 is activated. Function 70 can also be used to deactivate this feature, as follows: Activate Press: 70# [G1] 1#* [G1]. Deactivate Press: 70# [G1] 0#* [G1]. Note: If Function 70 is enabled, Output 3 cannot be included in the choices offered by Function 52. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the re- ceiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/ TV technician for help.
5 Visual LED Indicators LED In Normal Mode In Program Mode Red Remains lit while waiting for a keypress Confirms errors Blinks when editing an existing User Number Orange Flashes to confirm keypress Steady On to confirm in Program Mode. Flashes to confirm keypress Green Confirms activation of Outputs, mem- ory reset and Master Code reset Confirms valid data or empty User Number Audible Sounder Indicators Beep(s) In Normal Mode In Program Mode 1 short Unit power up and when a key is pressed Valid data confirmation 1 long Relay activation following a valid User Code Data recorded 4 short Data error Data Error 2 short Enter Program Mode Exit Program Mode TWO KEYPADS CONTROL ONE DOOR The below diagram displays how to control a single door with two keypads. When you enter a valid code on Keypad 2, the magnetic lock unlocks directly. When you enter a valid code on Keypad 1, the Request-to-Exit input of keypad 2 is triggered, unlocking the door. Note: Valid user codes must be programmed into both Keypads 1 and 2. WIRING EXAMPLES ONE KEYPAD CONTROLS A DOOR The diagram at right displays basic wiring-- how to control a single door with one keypad. When you enter a valid code on Keypad 1, the magnetic lock unlocks directly. This wiring is Fail Secure which means that if power is lost, the door will remain locked. NC NO NO C1 C2 P1 + – M NC S2 S1 OC A-100WP Electromagnetic Door Lock (Fail Secure) N/O Request- to-Exit Button 12-24 VDC / VAC Power NC NO NO C1 C2 P1 + – M NC S2 S1 OC A-100WP 12-24 VDC / VAC Power NC NO NO C1 C2 P1 + – M NC S2 S1 OC A-100WP Electromagnetic Door Lock (Fail Secure) 12-24 VDC / VAC Power
6 PROGRAMMING FUNCTIONS--OVERVIEW The audible sounder and visual LED indicators are displayed in the text below as follows: [O2] = Orange LED lights and sounder beeps twice [G1] = Green LED lights and sounder beeps once [R2] = Red LED lights and sounder beeps twice TIMER FUNCTIONS FUNCTION NUMBER DESCRIPTION PRESS THESE BUTTONS ON KEYPAD 21 Output 1 Activation Duration Program time from 01 to 99 seconds. Press: 21# [G1] ___ ___ #* [G1]. 22 Output 2 Activation Duration Program time from 01 to 99 seconds. Press: 22# [G1] ___ ___ #* [G1]. 23 Output 3 Activation Duration Program time from 01 to 99 seconds. Press: 23# [G1] ___ ___ #* [G1]. USER FUNCTIONS 30 Code Length Press: 30# [G1] ___ #* [G1]. 31 Modify Master Code Press: 31# [G1] (new MC) # [G1] (new MC) #* [G1]. 32 Add (or Edit) a User Code Press: 32# [G1] (User Number) # [G1] (User Code) # [G1] (re-enter User Code) #* [G1]. 33 Add (or Edit) a User Code with Output 1 Duration Press: 33# [G1] (time 01-99) # [G1] (User Number) # [G1] (User Code) # [G1] (re-enter User Code) #* [G1]. 34 Delete User Code Press: 34# [G1] (User Number) #* [G1]. 52 Add (or Edit) a User Code with Output Activation Press: 52# [G1] (2-digits) # [G1] (User Number) # [G1] (User Code) # [G1] (re-enter User Code) #* [G1]. FUNCTION NUMBER DESCRIPTION PRESS THESE BUTTONS ON KEYPAD SYSTEM FUNCTIONS FUNCTION NUMBER DESCRIPTION PRESS THESE BUTTONS ON KEYPAD 40 Reset Keypad Press: 40# [G1] 12345# [G1] 12345#* [G1]. 60 Sounder Beeps Always ON Press: 60# [G1] 1#* [G1]. OFF for User Codes: 60# [G1] 0#* [G1]. 70 Output 3 Activates on First Keypress Activate Press: 70# [G1] 1#* [G1]. Deactivate Press: 70# [G1] 0#* [G1]. FUNCTION NUMBER DESCRIPTION PRESS THESE BUTTONS ON KEYPAD 55 Enter Program Mode Press 55# [Master Code] * -- Exit Program Mode Press * PROGRAM MODE
7 MOUNTING TEMPLATE The A-100WP is designed to be installed in its stainless rugged mounting fixture. The fixture is 4 wide and 4¾ tall.
8 ALARM LOCK LIMITED WARRANTY ALARM LOCK SYSTEMS, INC. (ALARM LOCK) warrants its products to be free from manufacturing defects in materials and workmanship for 24 months following the date of manufacture. ALARM LOCK will, within said period, at its option, repair or replace any product failing to operate correctly without charge to the original purchaser or user. This warranty shall not apply to any equipment, or any part thereof, which has been repaired by others, improperly installed, improperly used, abused, altered, damaged, subjected to acts of God, or on which any serial numbers have been altered, defaced or removed. Seller will not be responsible for any dismantling or reinstallation charges. THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. THERE IS NO EXPRESS OR IMPLIED WARRANTY OF MERCHANTABILITY OR A WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. ADDITIONALLY, THIS WARRANTY IS IN LIEU OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF ALARM LOCK. Any action for breach of warranty, including but not limited to any implied warranty of merchantability, must be brought within the six months following the end of the warranty period. IN NO CASE SHALL ALARM LOCK BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLERS OWN NEGLIGENCE OR FAULT. In case of defect, contact the security professional who installed and maintains your security system. In order to exercise the warranty, the product must be returned by the security professional, shipping costs prepaid and insured to ALARM LOCK. After repair or replacement, ALARM LOCK assumes the cost of returning products under warranty. ALARM LOCK shall have no obligation under this warranty, or otherwise, if the product has been repaired by others, improperly installed, improperly used, abused, altered, damaged, subjected to accident, nuisance, flood, fire or acts of God, or on which any serial numbers have been altered, defaced or removed. ALARM LOCK will not be responsible for any dismantling, reassembly or reinstallation charges. This warranty contains the entire warranty. It is the sole warranty and any prior agreements or representations, whether oral or written, are either merged herein or are expressly canceled. ALARM LOCK neither assumes, nor authorizes any other person purporting to act on its behalf to modify, to change, or to assume for it, any other warranty or liability concerning its products. In no event shall ALARM LOCK be liable for an amount in excess of ALARM LOCKs original selling price of the product, for any loss or damage, whether direct, indirect, incidental, consequential, or otherwise arising out of any failure of the product. Sellers warranty, as hereinabove set forth, shall not be enlarged, diminished or affected by and no obligation or liability shall arise or grow out of Sellers rendering of technical advice or service in connection with Buyers order of the goods furnished hereunder. ALARM LOCK RECOMMENDS THAT THE ENTIRE SYSTEM BE COMPLETELY TESTED WEEKLY. Warning: Despite frequent testing, and due to, but not limited to, any or all of the following; criminal tampering, electrical or communications disruption, it is possible for the system to fail to perform as expected. ALARM LOCK does not represent that the product/system may not be compromised or circumvented; or that the product or system will prevent any personal injury or property loss by burglary, robbery, fire or otherwise; nor that the product or system will in all cases provide adequate warning or protection. A properly installed and maintained alarm may only reduce risk of burglary, robbery, fire or otherwise but it is not insurance or a guarantee that these events will not occur. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE, OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING. Therefore, the installer should in turn advise the consumer to take any and all precautions for his or her safety including, but not limited to, fleeing the premises and allege police or fire department, in order to mitigate the possibilities of harm and/or damage. ALARM LOCK is not an insurer of either the property or safety of the users family or employees, and limits its liability for any loss or damage including incidental or consequential damages to ALARM LOCKs original selling price of the product regardless of the cause of such loss or damage. Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion or limitation of incidental or consequential damages, or differentiate in their treatment of limitations of liability for ordinary or gross negligence, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights and you may also have other rights which vary from state to state.