Alarm Lock DL2800 Programming Instructions User Manual

							11 
ACTIVITY LED SOUNDER COMMENTS 
Keypress 1 RED Flash 1 Beep Normal Operation 
Access Granted or Remote Input 2 GREEN Flashes 2 Beeps For Remote Input, wire a normally 
open contact to these two white 
wires.  Momentarily close to 
unlock.  See page 10 for more in-
formation. 
Valid Code  1 Momentary GREEN 
Flash   
Invalid Code 6 RED Flashes 6 Beeps Re-enter User Code 
Successful Program Entry 1+2 GREEN Flashes 1+2 Beeps When in Program Mode 
Unsuccessful Program Entry 7 RED Flashes 7 Beeps When in Program Mode 
Enter Program Mode 2 YELLOW & 1 GREEN 
LED Flash   
Exit Program Mode 1 RED, 2 GREEN,  
1 RED Flashes 2 Groups of 5 
Beeps  
Valid but Disabled Code 1 RED, 1 GREEN, 4 
RED Flashes 1 long, 5 short 
Beeps Code exists in memory, but dis-
abled 
Low Battery upon User Code En-
try or upon closing of Remote Re-
lease switch YELLOW Flash during 
key presses Steady 4-Second 
Tone LED and sounder indications occur 
only when a valid code is entered.  
See page 10 before changing bat-
teries 
User Code Entered YELLOW Flash Sequence of 7 
Beeps Repeated 4 
Times  Non-fatal memory or clock error 
has been detected.  Under this 
condition, unexpected operation is 
possible.  Remove power and re-
start.  Do not mistake the low bat-
tery indication as a memory or 
clock error 
Button Press  Continuous Series 
of Beeps  System Fault.  Ensure batteries 
are fresh 
LED and Sounder Indicators 
The DL Series locks provide visual and audible keypad feedback.  With a fully charged battery, the LED and sounder feedback 
is as follows:  
						

							12 
Product Communication Examples 
NOTE:  
The AL-PCI cable is designed to be used on a 9 pin serial COM port.  If your computer has a 25 pin COM port, a 25 pin to 9 pin adapter must be used.   
Warning:  Polarity MUST be observed when connecting cables to the lock.  The tab (-) must plug into the negative (black) hole. 
Scenario 3   Use the AL-IR1 Infrared printer to print your lock’s audit trail (event log), User Code list, clock settings and software 
version.  No cable required. 
Scenario 1   Create the program in DL-Windows on your computer, then transfer the program from the computer directly to the lock via an 
AL-PCI cable.   
IBM COMPATABLE  
LAPTOP OR DESKTOP PC 
NOTE:  OBSERVE TAB DIRECTION WHEN 
INSERTING CABLE INTO LOCK 
AL-PCI CABLE 
CONNECT TO SERIAL PORT 
(COM 1-4) 
Scenario 2   Create the program in DL-Windows and transfer the program from your computer to an AL-DTM (via an AL-PCI cable)…
then transfer the program from the AL-DTM to the lock(s) (via a double-ended mini banana plug).  The hand-held AL-DTM is useful 
because you do not have to transport (or find electricity for) your computer.  Data can also flow in reverse, from the lock, through 
the AL-DTM, back to the computer for examination. 
IBM COMPATABLE  
LAPTOP OR DESKTOP PC 
NOTE:  OBSERVE TAB DIRECTION W HEN 
INSERTING CABLE INTO LOCK 
AL-PCI CABLE 
CONNECT TO SERIAL PORT 
(COM 1-4) 
AL-DTM DATA 
TRANSFER 
MODULE 
NOTE:  OBSERVE TAB DIREC-
TION WHEN INSERTING CABLE 
INTO AL-DTM AND LOCK 
DOUBLE-ENDED MINI BANANA 
PLUG CONNECTOR 
Send to lock Receive from lock 
AL-IR1  
INFRARED PRINTER 
If your computer does not have a serial COM port 
(DB-9 male) available, you can plug your AL-PCI2 
cable into a special USB to RS-232 cable.  Order 
part PCI-USB for the 
USB to RS-232 cable 
only, or ALPCI2-U for 
both the USB to RS-232 
cable and an AL-PCI2 
cable).  
						

							13 
Programming Functions--Overview 
Function 1 New Master Code  14 
Function 2 Add/Delete/Change User Codes 
2-200  14 
Function 3 Disabling Users (By User Num-
ber) 14 
Function 4 Enabling Users (By User Number) 14 
Function 5 User Enable with Timeout  15 
Function 6 Enable Total User Lockout Mode 15 
Function 7 Disable Total User Lockout Mode 15 
Function 8 Change User Programming Level 
Ability 15 
Function 9 Enable User 300 (Service Code) 15 
Function 10 Erase All Users Except the Mas-
ter Code (User 1)  15 
Function 11 Reserved 15 
Function 12 Clear All Schedules and Timeout  
Functions 16 
Function 13 Clear All Timeout Functions 16 
Function 14 - 17 Group 1-4 Disable 16 
Function 18 Disable All Groups 16 
Function 19 - 22 Group 1-4 Enable 16 
Function 23 Enable All Groups 16 
Function 24 Reserved 16 
Function 25 - 28 Timed Disable Groups 1-4 17 
Function 29 Timed Disable All Groups   17 
Function 30 - 33 Timed Enable Groups 1-4 17 
Function 34 Timed Enable All Groups   17 
Function 35 Group Add/Delete Association 17 
Function 36 - 37 Reserved 17 
Function 38 Set Date 18 
Function 39 Set Time 18 
Function 40 Set Weekday 18 
Function 41 Daylight Saving Time Start Date 18 
Function 42 Daylight Saving Time End Date 18 
Function 43 Speed Up Clock 19 
Function 44 Slow Down Clock 19 
Function 45 Enable Passage Mode 19 
Function 46 Disable Passage Mode 19 
Function 47 Timed Passage Mode 19 
Function 48 Enable Permanent Passage Mode 20 
Function 49 Disable Permanent Passage 
Mode 20 
Function 50 Return Lock to Normal Passage 
Mode Schedule 20 
Function 51 Set Pass Time 3 to 5 Seconds 20 
FUNCTION  
NUMBER DESCRIPTION PAGE  
NUMBER 
Function 52 Set Pass Time to 10 Seconds 20 
Function 53 Set Pass Time to 15 Seconds 20 
Function 54 Reserved 20 
Function 55 Print Audit Trail  21 
Function 56 Print User Code List  21 
Function 57 Print Clock Settings and Software 
Version  21 
Function 58 Upload/Download PC Data 21 
Function 59 Reserved 22 
Function 60 Number of Attempts Before Lock-
out  22 
Function 61 Set the Attempts Lockout Time 22 
Function 62 - 63 Reserved 22 
Function 64 Disable Remote Input 22 
Function 65 Enable Remote Input 22 
Function 66 Reserved 22 
Function 67 Reserved 23 
Function 68 Reserved 23 
Function 69 Enable Enter Key  23 
Function 70 Disable Enter Key 23 
Function 71 Reserved 23 
Function 72 Schedule Enable Passage Mode 
(Unlock) 24 
Function 73 Schedule Disable Passage Mode 
(Lock) 24 
Function 74 - 77 Schedule Enable Groups 1-4 24 
Function 78 Schedule Enable All Groups 24 
Function 79 - 82 Schedule Disable Groups 1-4 24 
Function 83 Schedule Disable All Groups 24 
Function 84 - 87 Quick Schedules - Enable Group 25 
Function 88 Passage Mode  
(Open Time Window) 25 
Function 89 Passage Mode  
(Close Time Window) 25 
Function 90 Reserved 26 
Function 91 Reserved 26 
Function 92 Enable Group 4  
(Open Time Window) 26 
Function 93 Enable Group 4  
(Close Time Window) 26 
Function 94 - 98 Reserved 26 
Function 99 Clear All Lock Programming  26 
FUNCTION  
NUMBER DESCRIPTION PAGE  
NUMBER  
						

							14 
Enabling/Disabling Users (By User Number) 
USERS 
Programming Functions 
1. New Master Code (User Number 1) ; 1      ; [ _ _ _ _ _ _ ]           ; [ _ _ _ _ _ _ ] : 
   (New Master Code)                  (Confirm New Master Code) 
•Master Code must be 6 digits-only. 
•Factory Default = 123456 
•NOTE:  Following a power up, it is highly recommended that Function 1 (New Master 
Code), be accessed and the factory default Master Code changed before programming 
any other functions.
 
•See Lock Design Overview on page 5 and Quick Start on page 6 for more informa-
tion about the Master Code. 
 M 
2. Add/Delete/Change User Codes 2-200  ; 2      ; [ _ _ _ _ ]  *              ; [ _ _ _ _ _ _ ] : 
(User Number)                                    (User Code) 
User Number must be between 2 and 200. 
•To delete a code, leave the User Code blank 
•User Code must be 3-6 digits 
•Each User Code can be thought of as a User or a person.  As long as each person possesses 
their own unique User Code, you can control access to the lock by adding or deleting User 
Codes.  See Terminology Used in this Manual on page 7 for more information. 
 
User Code Conflicts 
Care should be taken not to program a new User Code which matches the first digits of any other 
User Code--by default, only the code with the least number of digits would be recognized.   
For example:  If User Codes 123 and 123456 are both entered in the lock, only code 123 would 
be recognized. 
If you wish to program User Codes that match the first digits of other codes, see program Func-
tion 69. 
NOTE:  An error will sound if you try to program a new User Code that matches the first digits of 
the Master User Code (User Number 1).  3 
3. Disable User  ; 3      ; [ _ _ _ _ ] :  
                            
(User Number) 
4. Enable User  ; 4      ; [ _ _ _ _ ] :  
                            
(User Number) 
•User Number must be between 2 and 200. 
NOTE:  Will Enable/Disable Users even if the User is associated with an enabled Group.  Use Feature 3 to disable a specific User 
Number and their associated User Code.  If the disabled User Code is entered, the lock will flash 1 Green and 4 Red Flashes 
(with 1 long and  5 short beeps) indicating that the User Code exists in memory, but is disabled.  Function 4 will undo Function 3.  2  
						

							15 
USERS (Continued) 
8. Change User Programming Level Ability ; 8       ; [ _ _ _ ]           ; [ _ _ _ _ ] :  
                           (User Number)                (Programming Levels) 
Service Code is a One-Time-Only code.  Once it is used, it is disabled until enabled again. 
; 9 : 9. Enable User 300 (Service Code) 
User Number must be between 2 and 200.  The ability to program one or more Programming 
Levels may be selected. 
 Example 1: Allow Basic User 67 to program levels 1, 2 and 4.  Enter: 
; 8      ; 6 7      ; 1 2 4 : 
NOTE:  User 67 does not have access to Programming Functions with a Program Level 
Ability of 3. 
 Example 2: Prevent User 67 from programming any programming levels.  Enter: 
; 8      ; 6 7      : 
NOTE:   Having a Program Level Ability of 4 does not allow access to functions requiring 
a Program Level Ability of 3, 2 or 1.   If multiple levels are required, program for each 
level that is required.   
 3 
 2  2 
11. Reserved 
Programming Functions (contd) 
5. User Enable with Timeout  (Enter Timeout, XXX Hours) 
(This Function enabled through keypad only) ; 5     ; [ _ _ _ _ ]           ; [ _ _ _ _ ] :  
                           (User Number)                         (XXX Hours) 
•With Function 5, User Numbers must be between 2-200, 299 or 300.  Hours must be between 1-999.   
•Function 5 can temporarily override a disabled User (disabled using Function 3 above). 
•Since this is a temporary feature, Function 5 can only be enabled using the keypad. 
•Example:  Brian, User Number 157, rarely works at the office, but when he does, enable him for his 8 hour work day 
(008) by entering Program Mode and pressing:  ; 5   ; 157   ; 008 :. 
•NOTE:  Up to 4 Timeout Functions may be pending at any one time.  An error beep will sound when attempting to 
program more than 4 Timeout Functions.   
 2 
; 6 :  6. Enable Total User Lockout Mode (This Function enabled through keypad only) 
7. Disable Total User Lockout Mode (This Function enabled through keypad only) 
; 7 : 
User Lockout Mode  
Prevents all User Codes (Except User 1 Master Code) from operating the lock.  Note: Other program-
ming functions or schedules will NOT re-enable Users.  Users must be re-enabled with Function 7.  
Note:  Does not change the User enable/disable status.  Note:  If the lock is currently in Passage Mode 
(door unlocked) and Function 6 is programmed, the lock will remain in Passage Mode.  M 
; 1 0      ; 0 0 0 :  10. Erase All Users Except the Master Code (User 1)  (This Function enabled through keypad only) 
Erases all User Codes except the Master Code (User 1).  M  
						

							16 
CLEAR FUNCTIONS 
GROUPS 
24. Reserved 
Programming Functions (contd) 
Group Enable/Disable 
Enter the functions below to Enable/Disable Groups.  Functions 14 - 23 will each override 
existing scheduled events.  Therefore, Functions 14 - 23 are temporary, take effect im-
mediately, and are always overridden by future scheduled events that already exist within 
the lock programming.  2 
; 1 4 : 
; 1 5 : 
16. Disable Group 3 ; 1 6 : 
17. Disable Group 4 ; 1 7 : 
18. Disable All Groups ; 1 8 : 
19. Enable Group 1 ; 1 9 : 
20. Enable Group 2 ; 2 0 : 
21. Enable Group 3 ; 2 1 : 
22. Enable Group 4 ; 2 2 : 
23. Enable All Groups ; 2 3 : 
14. Disable Group 1 
15. Disable Group 2 PRIORITY ORDER  
 
 
 
1.    Disabled Users 
2.    Enabled Groups 
3.    Disabled Groups 
4.    Enabled Users 
 
The Priority Order details which Function will 
take effect before (have priority over) others.  
For example, as per the list above, Enabled 
Users have the lowest priority, and other Func-
tions can affect the status of these Users.  Dis-
abling a Group (Functions 14-18) will take pri-
ority over the enabled Users in that Group, 
disabling them.  Enabling Groups (Functions 
19-23) will take priority over those tasks lower 
in the list, and finally disabling a User (Function 
3) takes priority over all other tasks listed. 
; 1 2      ; 0 0 0 :  12. Clear All Schedules and Timeout Functions 
Function 12 clears all programmed Schedules and all Timeout Functions.  (To clear All Timeout Functions only, see 
Function 13 below).  Function 12 will clear all of the following:  All Schedule Functions 72 through 93, Timeout Functions 
5, 25 through 34 and Function 47.  Note:  Function 12 also resets Passage Mode and any disabled Groups.  After using 
Function 12, your Scheduled/Timeout features must be manually re-programmed.   
 
 NOTE:  Up to 4 Timeout Functions may be pending at any one time.  An error beep will sound when attempting to pro-
gram more than 4 Timeout Functions.  This Function only disables the timeout; the event associated with the timeout will 
remain 
 3 
; 1 3      ; 0 0 0 :  
Function 13 clears all Timeout Functions.  (To clear All Schedules and Timeout Functions, see Function 12 above).  
Function 13 will clear all of the following:  All Timeout Functions 5, 25-34 and Function 47.  After using Function 12, your 
Scheduled/Timeout features must be manually re-programmed.   
 
 NOTE:  Up to 4 Timeout Functions may be pending at any one time.  An error beep will sound when attempting to pro-
gram more than 4 Timeout Functions.  This Function only disables the timeout; the event associated with the timeout will 
remain 
 3 
13. Clear All Timeout Functions (This Function enabled through keypad only) 
Important:  It is the responsibility of the lock programmer to verify the proper lock/unlock conditions and Group conditions 
after programming the lock with Function 12 and 13.  
						

							17 
GROUPS 
36 - 37. Reserved 
Clear All Timeout Functions by entering Function 13.   NOTE:  
Programming Functions (contd) 
Group Enable/Disable with Timeout (Enter Timeout, XXX Hours) (Functions 25-34 are enabled through the keypad only) 
•Hours must be between 1-999.  Enter the functions below to Enable/Disable Groups for the amount of time entered in hours. 
         NOTE:   Only 4 Timeout Functions are allowed at any one time.  An error beep will sound when attempting to program more 
than 4 Timeout Functions.  Functions 25 - 34 will each override existing scheduled events.  Therefore, Functions 25 - 34 
are temporary, take effect immediately, and are always overridden by future scheduled events that already exist within 
the lock programming.   
 
•Example:  All 15 members of the Accounting Department are members of Group 4, and a schedule programmed in the 
departments door lock reflects their normal working hours of 9 AM through 5 PM, Monday through Friday.  But one day a 
special event occurs, and all Accounting Department members are requested to stay an extra hour until 6 PM.  There-
fore, at 5 PM, the manager (wishing to temporarily enable Group 4 users for an extra hour) enters Program Mode and 
presses:  ; 33   ; 001 :.  Likewise, if the manager wished to send his department home 
early at 3 PM, the manager could enter  ; 28   ; 002 :.  
 2 
; 2 5      ; [ _ _ _ ] : 
(XXX Hours) 25. Timed Disable Group 1   
; 2 6      ; [ _ _ _ ] : 
(XXX Hours) 26. Timed Disable Group 2   
; 2 7      ; [ _ _ _ ] : 
  (XXX Hours) 27. Timed Disable Group 3   
; 2 8      ; [ _ _ _ ] : 
  (XXX Hours) 28. Timed Disable Group 4   
; 2 9      ; [ _ _ _ ] : 
  (XXX Hours) 29. Timed Disable All Groups   
; 3 0      ; [ _ _ _ ] : 
  (XXX Hours) 30. Timed Enable Group 1   
; 3 1      ; [ _ _ _ ] : 
  (XXX Hours) 31. Timed Enable Group 2   
; 3 2      ; [ _ _ _ ] : 
  (XXX Hours) 32. Timed Enable Group 3   
; 3 3      ; [ _ _ _ ] : 
  (XXX Hours) 33. Timed Enable Group 4   
; 3 4      ; [ _ _ _ ] : 
  (XXX Hours) 34. Timed Enable All Groups   
;  3 5      ; [ _ _ _ ]           ; [ _ _ _ _ ] : 
   (User Number)                   (Groups) 
35. Group Add/Delete Association 
As per the table on page 9, the locks default programming from the factory associates certain User Numbers with certain 
Groups.  To override these default Group associations, Function 35 manually associates (or disassociates) a selected User 
with a selected Group.  During programming, Groups not selected are then disassociated from the User.  Function 35 is 
helpful when the number of Users you wish to add to a Group outgrows the number of User Numbers defaulted to a Group 
(50); or if an existing User joins a department and you wish to simply add them to a Group. 
•User Number must be between 2 and 200; Groups 1-4 (to associate with User) may be selected. 
 Add Example: To associate User 67 with Groups 1, 2 and 4;   Enter: ; 3 5      ; 6 7     ; 1 2 4 : 
Delete Example: To remove all Group associations for User 67;  
 Enter: ; 3 5      ; 6 7 :  NOTE:  If a User is associated with more than one Group, all associated Groups would have to be disabled before the User is dis-
abled. 
 3  
						

							18 
CLOCK SETTINGS 
Programming Functions (contd) 
; 3 8      ; [ _ _ _ _ _ _ ] :  
  
(Date) 
38. Set Date 
•Use Month Day Year format - MMDDYY - Single digit months and days are entered with a preceding zero. 
•Enter ONLY the last two digits of the year. 
 
For Example: March 8, 2005;  
 Enter: ; 3 8      ; 0 3   0 8    0 5 : 
 3 
39. Set Time ; 3 9      ; [ _ _ _ _ ] :  
  
(Time) 
•Time must be 4 digits 
•Use 24 Hour Format (add 12 hours to program PM time) 
 For Example:  To set time to 8:25 PM;   
 
 
Enter: ; 3 9      ; 2 0 2 5 :  For Example:  To set time to 8:25 AM;   
 
 
Enter: ; 3 9      ; 0 8 2 5 : 
 3 
; 4 0      ; [ _ ] :  
  (Day) 40. Set Weekday 
•For day enter: 1 for Sunday, 2 for Monday, 3 for Tuesday, 4 for Wednesday, 
5 for Thursday, 6 for Friday and 7 for Saturday.  For Example:  To set day to Sunday;   
 
 
Enter: ; 4 0      ; 1 : 
 3 
41. Daylight Saving Time Start Date ; 4 1 ; [ M M W D ] :  
(DST Starting Month, Month, Week, Day) 
The manner in which Daylight Saving Time (DST) is observed varies with location, therefore the DST adjustment is fully flexible to 
accommodate these regional differences.  Function 41 allows the entry of a DST Start Date (month, day and week), and Function 42 
allows the entry of a DST End Date (month, day and week).  DST begins and ends at 2AM on the programmed date.  Enter ; 
4 1 ; 0 0 0 : to disable DST.  All locks leave the factory with DST enabled and pre-programmed to the 
following start and end dates (for the USA beginning 2007): 
 
•Default DST Start Date: March, Week 2, Sunday (Second Sunday in March) 
•Default DST End Date:    November, Week 1, Sunday (First Sunday in November)  
To program the DST start date using the keypad, press:  ; 4 1 ; [ M M W D ] : where M M W D represents:  
•M M = Two digits of the month (01 through 12 = January through December.  Single digit months are entered with a 
preceding zero). 
•W = Single digit for week of the month (valid entries are 1-5 where 1 is the first week, 2 is the second week, 3 is the 
third week, 4 is the fourth week and 5 is the last week of the month. 
•D = Day of the week (valid entries are 1-7:  1 for Sunday, 2 for Monday, 3 for Tuesday, 4 for Wednesday, 5 for Thursday, 6 
for Friday and 7 for Saturday).   
 Example:  To set the default start date of second Sunday in March, press:  
                ; 4 1 ; [ 0 3 2 1 ] : (03 = March,  2 = 2nd week, 1 = Sunday). 
 4 
42. Daylight Saving Time End Date ; 4 2 ; [ M M W D ] :  
(DST Ending Month, Month, Week, Day) 
End date of Daylight Saving Time (month, week, day).  Enter ; 4 2 ; 0 0 0 : to disable DST.  
See Function 41 for full explanation.  4  
						

							19 
CLOCK ADJUST 
PASSAGE MODE 
Programming Functions (contd) 
; 4 5 : 45. Enable Passage Mode (This Function enabled through keypad only) 
; 4 6 : 46. Disable Passage Mode (This Function enabled through keypad only) 
47. Timed Passage Mode (This Function enabled through keypad only) 
; 4 7      ; [ _ _ _ ] :  
(XXX Hours) 
•Function 45 allows passage through the door without the need for a User Code.  Re-Lock using Function 46.   
•Programmed Schedules will override the state of the lock when Functions 45 and 46 are used.  If it is required that pro-
grammed schedules do not override Passage Mode, enable/disable Passage Mode using Functions 48/49.  Note:  Because 
of the temporary nature of these features, Functions 45-47 can only be enabled using the keypad. 
Passage Mode Enable/Disable - Schedule will Override  
 2 
•Hours must be between 1 - 999. Function 47 allows passage through the door without the need for a User Code for the programmed amount of time.  
 
 
 
•For example, if you wish your office door lock to be unlocked (unlocked = Passage Mode) for the next 3 hours, 
enter Program Mode and press:  ; 47 ; 003 :     
 2 
; 4 3           ; [ _  _ ] :  
(seconds) 
43. Speed Up Clock (This Function enabled through keypad only) 
; 4 4           ; [ _  _ ] :  
(seconds) 
44. Slow Down Clock (This Function enabled through keypad only) 
Number of seconds to adjust (speed up/slow down) the clock each day must be be-
tween 0-55 seconds. 
Note:  Repeated use of these Functions are not cumulative (this means, for example, 
if the clock has already been set to speed up 10 seconds per day, and then is found to 
need an additional 10 seconds, then program 20 seconds using Function 43). 
 
Example 1:  Clock is losing 13 seconds every day, enter: 
 ; 4 3       ; 1 3 :.  
This example assumes that the Clock Adjust setting was at the factory default of zero.  
Function 57 can be used to print the current Clock Adjust setting. 
 
Example 2:  Clock is gaining 13 seconds every day, enter: 
 ; 4 4       ; 1 3 :.  
This example assumes that the Clock Adjust setting was at the factory default of zero. 
Function 57 can be used to print the current Clock Adjust setting. 
 
Example 3:  To set the clock adjust setting back to the factory default of zero, enter
:  ; 4 3 :  or ; 4 4 : 
Clock Adjust  
 4 
Clock Accuracy 
The internal oscillator is factory calibrated to an accu-
racy of ±5 minutes/year.  Changes in ambient tem-
perature may affect accuracy.  If necessary, the ac-
curacy of the internal clock may be adjusted by first up-
dating the correct time via Function 39.  After an interval 
of about 1 month, re-set the correct time via Function 39 
and then print an Audit Log via Function 55.  Because 
the Audit Log displays both the New Clock Time and 
the Old Clock Time, a daily accuracy (in seconds) can 
be determined by taking the difference in seconds be-
tween the Old and New times divided by the number 
of days between the two Function 39 entries.  Note:  
Because the minimum available adjustment is 1 second 
per day, the inaccuracy of the clock must exceed about 6 
minutes per year before adjustment is necessary.  
						

							20 
; 5 1 : 51. Set Pass Time 3 to 5 Sec. 
; 5 2 : 
; 5 3 : 
Pass Time 
52. Set Pass Time to 10 Sec.
53. Set Pass Time to 15 Sec.
54. Reserved 
PASS TIME 
Programming Functions (contd) 
49. Disable Permanent Passage Mode (This Function enabled through keypad only) 
50. Return Lock to Normal Passage 
Mode Schedule 
(This Function enabled through keypad only) (Locks will lock or unlock depending on the current schedule).  Use Function 50 to undo 
Functions 48 and/or 49, and therefore return the lock to all pre-existing scheduled functions. 
•Function 48 allows passage through the door without the need for a User Code.  Re-Lock using Function 
49. 
•Programmed Schedules will not override the state of the lock using functions 48 and 49.  If it is required 
that programmed schedules override Passage Mode, Enable/Disable Passage Mode using Functions 
45/46.  Use Function 50 to undo Functions 48 and/or 49, and therefore return the lock to all pre-existing 
scheduled functions.  Note:  Functions 48-50 can only be enabled using the keypad.  Warning:  Function 
49 will inhibit all scheduled Passage Mode events. 
Passage Mode Enable/Disable - Schedule will not Override 
 2 
PERMANENT PASSAGE MODE 
; 4 9 :  
48. Enable Permanent Passage Mode (This Function enabled through keypad only) 
; 4 8 :  
; 5 0 :  
See Scheduled functions 72 and 73 for Scheduled Passage Mode. NOTE:  
The Pass Time is the length of time the lock stays unlocked after a valid User Code is en-
tered.  When the Pass Time expires, the lock will re-lock automatically.  Use the functions 
below to change the Pass Time to 3-5, 10 or 15 seconds.  The Pass Time is defaulted to 
3-5 seconds.    4