Alarm Lock DL1200 Programming Instructions User Manual

							11 
When a valid code is entered and the batteries are weak, the 
red & green LEDs will light and the sounder will sound for 4 
seconds.  The DL1200 uses two 123 Type Lithium batteries 
(Duracell P/N CR17345).  The lock will function with weak 
batteries; however be sure to replace them as soon as 
possible. 
 If the DL1200 is ever without power for less than 1 minute 
(such as when replacing batteries), the DL1200 will continue its 
operation undisturbed--programming remains unaffected due 
to power provided by capacitors inside the lock.  If the DL1200 
is without power for greater than one minute, you have two 
choices--you can (1) retain the lock programming or (2) erase 
all programming.  If you choose to erase all programming, the 
DL1200 will revert to its original factory default configuration 
(out of the box). 
 CAUTION:  Do not press any keys while batteries are dis-
connected unless you intend to erase all programming.    1.Insert key in cylinder and turn counterclockwise to al-
low access to the battery compartment screw.  With the 
supplied 5/64 Allen wrench, loosen the battery cover 
screw only until the battery cover is able to slide off.   
2.Pull out the battery pack and quickly replace both 
batteries - within 1 minute. 3.If you do not hear the 3 beeps when power is re-
applied, all programming and settings have been re-
tained, and the lock is ready for use.  Go to step 5. 
4.If you do hear 3 beeps when power is re-applied, do 
not press any keys for 15 seconds.  After the 15 
second period, the LED will flash red 6 times and 6 
beeps will sound.  Reset the clock using functions 38, 39 
and 40.   
5.Slide the battery cover back in place and tighten the 
screw. 
 If you accidentally press a key (or fail to replace the batteries 
within 1 minute), use the Retain Lock Programming proce-
dure below: 
 
Retain Lock Programming 
1.    Re-install battery pack. 
2.    Do not press any keys for 10 seconds. 
 If you do not hear any beeps or if you hear 3 beeps (one 
per second), the previous lock programming is retained and 
the lock is now ready for use.  If you test the DL1200 and 
find the lock programming is lost, you may erase all pro-
gramming and return the DL1200 to its original factory set-
tings, as described below. 
Battery Replacement 
Erase All  Programming 
RESTORE FACTORY DEFAULT (original out of box settings 
that were set at the factory will be loaded). 
1.  Enter the current Master Code (if not known, proceed di-
rectly to ALTERNATIVE METHOD, below).  Wait for the 
green light and press ; until multiple beeps are heard.  
You are now in Program Mode. 
2.  Within 5 seconds (or current pass time interval), 
press ; 99 ; 000 :. 
3.  Listen for 6 beeps.  The lock will re-lock.  All settings and 
programming have been erased.  Proceed directly to page 
12, Quick Start, and follow the procedure Enter Program 
Mode and Change Factory Master Code. 
 
ALTERNATIVE METHOD 
Note:  This method requires the lock first be removed from 
the door. 
1.  Insert key in cylinder and turn counterclockwise to al-
low access to the battery compartment screw.  With the 
supplied 5/64 Allen wrench, loosen the battery cover 
screw only until the battery cover is able to slide off.   
2.  Disconnect the battery pack.   
3.  Remove the back plate by unscrewing the two Phillips 
head screws.  Note:  Some models have four Phillips 
head screws.  Be careful not to damage the motor drive 
wires.   
4.  Locate jumper header JP1 near the top of the printed 
circuit board and install the jumper (provided) across pins 
1 and 2 of JP1. 
5.  Press and hold down ; for 10 seconds (to ensure all power is drained from the lock) and release. 
6.  Connect the batteries and--within 5 seconds--press 
and hold ;.  After hearing 6 additional beeps, re-
lease ;.  If you do not hear these 6 additional 
beeps, you must start over at step 2.  Failure to follow 
this exact procedure can result in erratic lock behavior.   
7.  Test by pressing the default Master Code of 
123456 (a beep will sound 
and the lock will unlock). 
8.  Remove the jumper from JP1 pins 1 and 2 and place 
jumper on 1 pin for storage.   
9.  Carefully reinstall the back plate STRAIGHT onto the 
lock body.  Be careful not to pinch or damage the motor 
drive wires.  While inserting the back plate, be sure the 
rear pin of the tailpiece inserts into the spindle hole--
check this alignment after installation by pushing on the 
spring-loaded tailpiece to verify that it smoothly moves 
up and down.  Replace the two (or four) Phillips head 
screws to secure the back plate.  Note:  It may be nec-
essary to tighten the battery screw previously loosened 
in step 1.   
10. Re-mount the lock on the door.  With the battery 
back inside its compartment, slide the battery cover 
back in place and tighten the screw.   
      All  settings  and  programming  have  been  erased.    Pro-
ceed directly to page 12, Quick Start, and follow the 
procedure Enter Program Mode and Change Fac-
tory Master Code.  
						

							12 
ALARM LOCK SYSTEMS, INC. (ALARM LOCK) 
warrants its products to be free from manufacturing 
defects in materials and workmanship for 24 months 
following the date of manufacture. ALARM LOCK will, 
within said period, at its option, repair or replace any 
product failing to operate correctly without charge to 
the original purchaser or user. 
This warranty shall not apply to any equipment, or 
any part thereof, which has been repaired by others, 
improperly installed, improperly used, abused, altered, 
damaged, subjected to acts of God, or on which any 
serial numbers have been altered, defaced or 
removed. Seller will not be responsible for any 
dismantling or reinstallation charges. 
THERE ARE NO WARRANTIES, EXPRESS OR 
IMPLIED, WHICH EXTEND BEYOND THE 
DESCRIPTION ON THE FACE HEREOF. THERE IS 
NO EXPRESS OR IMPLIED WARRANTY OF 
MERCHANTABILITY OR A WARRANTY OF 
FITNESS FOR A PARTICULAR PURPOSE. 
ADDITIONALLY, THIS WARRANTY IS IN LIEU OF 
ALL OTHER OBLIGATIONS OR LIABILITIES ON 
THE PART OF ALARM LOCK. 
Any action for breach of warranty, including but not 
limited to any implied warranty of merchantability, must 
be brought within the six months following the end of 
the warranty period. IN NO CASE SHALL ALARM 
LOCK BE LIABLE TO ANYONE FOR ANY 
CONSEQUENTIAL OR INCIDENTAL DAMAGES 
FOR BREACH OF THIS OR ANY OTHER 
WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE 
LOSS OR DAMAGE IS CAUSED BY THE SELLERS 
OWN NEGLIGENCE OR FAULT. 
In case of defect, contact the security professional 
who installed and maintains your security system. In 
order to exercise the warranty, the product must be 
returned by the security professional, shipping costs 
prepaid and insured to ALARM LOCK. After repair or 
replacement, ALARM LOCK assumes the cost of 
returning products under warranty. ALARM LOCK 
shall have no obligation under this warranty, or 
otherwise, if the product has been repaired by others, 
improperly installed, improperly used, abused, altered, 
damaged, subjected to accident, nuisance, flood, fire 
or acts of God, or on which any serial numbers have 
been altered, defaced or removed. ALARM LOCK will 
not be responsible for any dismantling, reassembly or 
reinstallation charges. 
This warranty contains the entire warranty. It is the 
sole warranty and any prior agreements or 
representations, whether oral or written, are either 
merged herein or are expressly cancelled. ALARM 
LOCK neither assumes, nor authorizes any other person purporting to act on its behalf to modify, to 
change, or to assume for it, any other warranty or 
liability concerning its products. 
In no event shall ALARM LOCK be liable for an 
amount in excess of ALARM LOCKs original selling 
price of the product, for any loss or damage, whether 
direct, indirect, incidental, consequential, or otherwise 
arising out of any failure of the product. Sellers 
warranty, as hereinabove set forth, shall not be 
enlarged, diminished or affected by and no obligation 
or liability shall arise or grow out of Sellers rendering 
of technical advice or service in connection with 
Buyers order of the goods furnished hereunder. 
ALARM LOCK RECOMMENDS THAT THE ENTIRE 
SYSTEM BE COMPLETELY TESTED W EEKLY. 
Warning: Despite frequent testing, and due to, but 
not limited to, any or all of the following; criminal 
tampering, electrical or communications disruption, it is 
possible for the system to fail to perform as expected. 
ALARM LOCK does not represent that the product/
system may not be compromised or circumvented; or 
that the product or system will prevent any personal 
injury or property loss by burglary, robbery, fire or 
otherwise; nor that the product or system will in all 
cases provide adequate warning or protection. A 
properly installed and maintained alarm may only 
reduce risk of burglary, robbery, fire or otherwise but it 
is not insurance or a guarantee that these events will 
not occur. CONSEQUENTLY, SELLER SHALL HAVE 
NO LIABILITY FOR ANY PERSONAL INJURY, 
PROPERTY DAMAGE, OR OTHER LOSS BASED 
ON A CLAIM THE PRODUCT FAILED TO GIVE 
WARNING. Therefore, the installer should in turn 
advise the consumer to take any and all precautions 
for his or her safety including, but not limited to, fleeing 
the premises and calling police or fire department, in 
order to mitigate the possibilities of harm and/or 
damage. 
ALARM LOCK is not an insurer of either the property 
or safety of the users family or employees, and limits 
its liability for any loss or damage including incidental 
or consequential damages to ALARM LOCKs original 
selling price of the product regardless of the cause of 
such loss or damage. 
Some states do not allow limitations on how long an 
implied warranty lasts or do not allow the exclusion or 
limitation of incidental or consequential damages, or 
differentiate in their treatment of limitations of liability 
for ordinary or gross negligence, so the above 
limitations or exclusions may not apply to you. This 
Warranty gives you specific legal rights and you may 
also have other rights which vary from state to state. 
Alarm Lock Limited Warranty