Alarm Lock DL1200 Programming Instructions User Manual

1 
CONGRATULATIONS!    
Your new DL1200 Alarm Lock Trilogy electronic digital lock is a manually 
programmable narrow stile entry trim for Adams Rite® 4710, 4730 and 
4900 deadlatch locks, and 1850, 1950, 4070, MS1850S and MS1950S 
series deadbolts for narrow stile aluminum doors*.  The DL1200 is a rug-
ged entry lock of advanced design with several programmable features.  
Three security levels are provided:  Master (can perform ALL functions), 
Manager (can perform MOST functions plus entry), and Basic...

2 
Quick Start 
First Time Start Up 
1.  Unpack the lock from its factory packaging. 
2.  Connect the battery pack.   
3.  Listen for 3 beeps.  The lock is now ready to accept programming.  Note:  Failure to follow this exact proce-
dure can result in erratic lock behavior.   
 
       Important  Note:   When entering any key sequence below, do not pause more than 5 seconds between any 
key presses--otherwise you must start again.  (Note:  If you wish, this 5-second delay between key presses 
can be...

3 
Quick Start (cont’d) 
Enter a Manager Code 
Manager Codes are located at locations 00, 10, 20, 30, 40, 50, 60, 70, 80, and 90 (see grid on page 4).  Note:  
New Manager Codes MUST use the same number of digits as the (new) Master Code.  Enter as follows.   
1.   Press the (new) Master Code. 
2.   Press 
; [press a Manager location i.e. 00, 10, 20, 30, 40, 50, 60, 70, 80, or 90] ;.  
3.  Press a new Manager Code using the same number of digits as the (new) Master Code
.  A 6-beep acknowl-
edgement...

4 
The DL1200 lock provides three security levels:  Master (can perform ALL functions), Manager (can perform SOME program-
ming functions plus entry), and Basic User (entry only).  In total, there are 104 locations inside the DL1200 lock:  one Master 
Code, 10 Manager and 90 User Access Codes, and three one-time entry Service Codes.  Where the Access Code is located 
will determine its security level.  From the factory, all locations (except for the Master Code) are empty; each location can then be...

5 
User Access Codes allow access only; Manager Codes allow more:  Manager Codes have the ability to program and delete 
User Access Codes within that Managers Bank (column).  The DL1200 lock can hold up to 10 Manager Codes, one for 
each Bank (locations (00), (10), (20), (30), (40), (50), (60), (70), (80), (90)), and are all found at the top row of the grid be-
low.  Note:  Only the Master Code can add or delete a Manager Code. 
 In addition, Managers not only possess programming abilities for User...

6 
Programming Worksheet:  Functions 
FUNCTION PRESS THESE BUTTONS ON KEYPAD 
Change Existing Master Code [Enter Factory or Existing Master Code] ;1; [Enter New Master Code _ _ _ _ _ ] ;  
[Re-enter New Master Code _ _ _ _ _ ] [6 beeps = OK] 
Add/Change Manager Codes (up to 10) [Enter Master Code] ; [Enter 2-digit Manager Location _ _ ] ; 
     [Enter new Manager Code _ _ _ _ _ ] [6 beeps = OK] 
Add/Change User Codes (up to 90) Press Master or Manager Code ; [Enter 2-digit Location _ _ ] ; [Enter new...

7 
Change Existing Master Code*  ; 1 ; 
[ __ __ __ __ __ ]   ; 1 ;     [ __ __ __ __ __ ] ;    [ __ __ __ __ __ ] 
Old (or Factory) Master Code                                           New Master Code*                   Confirm New Master Code* 
For new locks, follow the Quick Start on page 2. 
Programming Functions 
* Once the number of digits is selected, it cannot be changed unless all programming is erased and the Factory Default settings are re-loaded 
(power must be removed and re-applied as per...

8 
Programming Functions (contd) 
Disable All:  If Master Code is used, disables all 100 User\Manager Codes and clears all 3 Service Codes.  If 
a Manager Code is used, disables all Users (even across multiple Banks) under that Manager.   
Disable Users Only:  If Master Code is used, disables all 90 Users and clears all 3 Service Codes, while Manag-
ers remain active.  If a Manager Code is used, disables all Users (even across multiple banks) under that Man-
ager. 
Enable All:  If Master Code is used,...

9 
[ __ __ __ __ __ ]   ; 301 ;   [ __ __ __ __ __ ]  
   Master/Manager Code**                                                                      New Service Code 
Service Codes are one-time-only Codes; once entered into the keypad, it is deleted.  Use the same Code up 
to 3 times by programming all three Service Codes with the same Code.  Note:  Service Codes are lost if 
power is removed.  To delete a single Service Code, press 
;, enter Service Code number (301, 302 or 
303), then press 
; :....

10 
Programming Functions (contd) 
The DL1200 is capable of emitting 1 of 4 possible keypress sounds: 
•High Frequency Keypad Feedback + Led 
•Low Frequency Keypad Feedback + Led 
•Click! Keypad Feedback + Led 
•Led Only  
[ __ __ __ __ __ ]   ; 220 ;   
           Master Code** 
High Freq KP Keypress Sound + Led 
(Default)
 
   Keypress Sound Options  
[ __ __ __ __ __ ]   ; 221 ;   
           Master Code** 
Low Freq KP Keypress Sound + Led 
[ __ __ __ __ __ ]   ; 222 ;   
           Master Code**...