Aiphone IS IP Network Direct Operation Manual

21
GETTING STARTED USING THE SYSTEM APPENDIX
SETTING AND ADJUSTMENT
Answering a call
The maximum duration of communication is preset in the 
System setting. (It can be set to a maximum of 10 minutes.)
Answer the call in one of the following ways.1 
■ Communication in the hands-free mode
(Available when COMMUNICATION METHOD is set 
to HF in the INITIAL SETTING)

Press 1) TALK momentarily.
  After a beep, you can communicate in the hands-
free mode.
*1: When talking: 
 (Lit)
When listening to the caller:...

22
■ Communication by using the handset

Lift the handset and you can communicate with the 1) handset.
*  You can also communicate in the press-to-talk 
mode by pressing and holding TALK
.
When you have fi nished the communication, put the 2) handset on the hook.
Communication will end.

  You can communicate in the press-to-talk mode by 
pressing and holding TALK
 even when you are 
communicating with the handset.
NOTE:
Communication will end automatically according to the set 
communication time.
About...

23
GETTING STARTED USING THE SYSTEM APPENDIX
SETTING AND ADJUSTMENTWide
Zoom
Viewing video images at a video door 
station
You can view video images at the target station when receiving 
a call from or communicating with a video door station, or 
monitoring a video door station in your site. The video images 
can be adjusted as necessary by using the following functions 
on the master station.
■ Switching Zoom/Wide
The display mode on the monitor can be switched between 
zoom and wide by each press of...

24
■ Adjusting images
If the image on the monitor is diffi cult to see, you can adjust the 
image.
Press 1 ADJUST when the image is diffi cult to see.
The backlight or night sensitivity is automatically adjusted.
The discrimination between day and night is performed 
* 
automatically by the door station.
The adjustment result may vary depending on the System 
* 
setting on a PC. 
To restore the image before adjustment
Press 
ADJUST again.
The icon is cleared and the image before adjustment is 
restored....

25
GETTING STARTED USING THE SYSTEM APPENDIX
SETTING AND ADJUSTMENT
Transferring to another master station 
You can transfer a call received from a door station to another 
master station while communicating with it (communication 
transferring), as well as setting calls to be automatically 
transferred in the INITIAL SETTING.
For a call from another master station, you can transfer it 
* 
when you are communicating with it. However, you cannot 
transfer the communication to a remote site.
■...

26
Door release
You can release the door lock while being called from, 
communicating with, or monitoring a door station if a door 
release device is connected to the station. 
Press    while being called from, communicating with, 
or monitoring the door station.
The door lock is released for the time set in the System setting 
on a PC.
If the set release time is “0”, it can be released while the 
* 
button is pressed and held.
NOTES: 
To enable door release to a door station in a remote site, the...

27
GETTING STARTED USING THE SYSTEM APPENDIX
SETTING AND ADJUSTMENT
Searching for a station, zone or remote site 
Read this section before you perform calling, monitoring or paging for the fi rst time to learn how to search for stations, zones or remote sites. 
The search can be performed in the following search methods by using the search items, dial keys or speed dial buttons to suit your needs.
PERFORMING CALLING, MONITORING AND PAGING ON 
THE MASTER STATION
The following describes how to operate the...

28
[In the SEARCH LIST]
Press 
1 LIST or ZOOM/WIDE in the standby mode.
The search items are shown in the SEARCH LIST.
Press 2  repeatedly to select the target search item A to E (so that it is highlighted).
Press 3 ZOOM/WIDE to decide on the selected one.
B STATIONS BY AREA (→P. 30)
A NAME SEARCH (→P. 29)
C STATIONS BY TYPE (→P. 30)
D PAGING ZONE (→P. 31)
(Not available both in a network direct 
system in your site and to a network 
direct system in a remote site)
LISTZOOM/WIDE
Search items
(001/002)
E...

29
GETTING STARTED USING THE SYSTEM APPENDIX
SETTING AND ADJUSTMENT
Searching for a station, zone or remote site 
from the list
A Searching for a station or zone in your site by 
entering the name [NAME SEARCH]
 Select [NAME SEARCH] either in the standby mode 
1 (→P. 27) or the SEARCH LIST (→P. 28).
Enter a name by using the dial keys.
2  (→P. 37) 
 e.g.) 
When searching for MASTER004; 
Press the dial keys as follows.
                                  
M00
AS4
TER
(4 times) (3 times) (8 times) (8 times)...

30
B Searching for a station in your site by 
designating an area [STATIONS BY AREA]
Select [STATIONS BY AREA] either in the standby 
1 mode (→P. 27) or the SEARCH LIST. (→P. 28)
Press 
2  to select the target area from the list (so 
that it is highlighted), and then press 
ZOOM/WIDE
 
to select.
All the stations in the area are displayed in the list.
Press 3  to select the target station (so that it is 
highlighted).
You can select up to 5 stations. * (→P. 29) 
Start calling (talking), monitoring or...