Aimco Brakes Cordless Tool Signature Series SPC2PGM Tool Speed Programmer User Manual

1
SPC-2PGM  
Tool Speed Programmer 
PO Box 16460, Portland OR 97292-0460  • 800-852-1368 • Fax 800-582-9015
www.aimco-global.com
INSTRUCTION MANUAL 

2 

3
TABLE OF CONTENTS
General Safety Rules  . . . . . . .3
Functional Description . . . . . .4
Operation Diagram  . . . . . . . .4
Programmer Operation  . . . . .5–13
Information Menu Page . . . . .14
WARNING! READ ALL INSTRUCTIONS COMPLETELY BEFORE OPERATION. Comply with 
all the instructions and rules in this manuaL . Keep these instructions in a safe place .
SAVE THESE  INSTRUCTIONS.
Please read this manual carefully before operation and follow the instructions  .
1 . Avoid exposing programmer to water...

4
FUNCTIONAL DESCRIPTION
Notes:
1 . Please install a fully charged battery pack onto the tool before using the programmer to 
make adjustments to the tool .  The tool battery is the power source for the programmer  .
2 . Only Forward rotation (CW) rpm is adjustable . The Reverse rotation (CCW) rpm is 
locked in at the maximum rpm capability of the tool .
3 . Only clutch trip count (CNT) is resettable; total tool clutch trip count is not resettable  .
4 . After changing settings with the SPC-2PGM...

5
PROGRAMMER OPERATION
Tool Speed (RPM) Setting
Note: Tool speed is preset to maximum from the factory
Step 1: Plug USB connector into 
Programmer using supplied USB to 
USB Mini cable
Plug USB connector into Programmer as shown.
Step 2: Plug mini USB connector into 
the tool as shown using supplied USB 
to USB mini cable . Press tool trigger 
momentarily to switch Programmer on 
and the Setup Menu, RPM EDIT screen 
displays automatically  .
Plug mini USB into the tool as shown. Angle Nutrunners will...

6
Step 5: Press “+” or “–” to increase or 
decrease RPM of tool CW rotation in 
50 RPM increments . The display shows 
the RPM range of the tool connected 
to the programmer (250–600 is 
shown as an example) .
Increase rpm.
Decrease rpm.
Step 6: Press “SAVE” and the value 
will be stored into the tool that is 
connected to the programmer  .
Press to save value.
Step 7: Press “EXIT” to leave the RPM 
setting and go to Setup Menu .
Press EXIT to return to Setup Menu.
Step 8: When at “Setup Menu,” press...

7
FR Mode Setting
For forward and reverse selection options
Step1: Press “Enter” for mode 
selection .
Press ENTER for mode selection.
Step 2: Press “” to find the 
“FR Mode” then press “EDIT” to enable 
changes .
Press EDIT to get into FR Mode.
Step 3: Press “ +” or “– “ to choose the 
FR mode you prefer:
(1) “0” enables the Forward (CW) 
and Reverse (CCW) selections on 
the tool to operate manually  . 
(2)  “1” enables the Forward 
(CW) operation to resume 
automatically after the tool runs 
in Reverse...

8
Buzzer Volume Adjustment
Step 1: Press “ENTER” for mode 
selection .
Press ENTER for mode selection.
Step 2: Press “” to find the 
Buz Volume mode and press “EDIT” to 
enable changes .
Press button to find Buz Volume Mode.
Press EDIT to start setting buzzer volume.
Step 3: Press “+” or “–” to increase or 
decrease the tool buzzer volume  . 
0 = Mute (no sound)
1 = Low buzzer volume
2 = Medium buzzer volume
3 = Loudest buzzer volume
  Increase volume 
Decrease  volume 
Step 4: Press “SAVE” and the value...

9
Start Mode Setting
For trigger starting options
Step 1: Press “ENTER” for mode 
selection .
Press ENTER for mode selection.
Step 2: Press “” to find the 
“Start_Mode” then press “EDIT” to 
enable changes .
Press EDIT to enter Start Mode.
Step 3: Press “+ “or “– “ to select the 
Start Mode you prefer  .
(1) “0” Setting: 
- First stage of trigger pull is to 
switch on the LED light .
- Second stage of trigger pull will 
start full speed run down .  If the 
clutch fails to trip (NG), the tool 
LED will...

10
Step 4: Press “SAVE” and the value 
will be stored into the tool that is 
connected to the programmer .
Press SAVE to complete the setting.
PROGRAMMER OPERATION
NOTES