AEG Steam oven BS836680KM User Manual

							FoodContainer
(Gastro-
norm)Quantity
(g)Shelf po-
sitionTempera-
ture (°C)Time
(min)CommentsBroccoli1)1 x 1/2 per-
forated30039913 - 15Put the bak-
ing tray on
the first shelf
position.Broccoli1)2 x 1/2 per-
forated2 x 3002 and 49913 - 15Put the bak-
ing tray on
the first shelf
position.Broccoli1)1 x 1/2 per-
foratedmax.39915 - 18Put the bak-
ing tray on
the first shelf
position.Frozen peas2 x 1/2 per-
forated2 x 13002 and 499Until the
tempera-
ture in
the cold-
est spot
reaches
85 °C.Put the bak-
ing tray on
the first shelf
position.1)  Preheat the oven for 5 minutes.12.  CARE AND CLEANINGWARNING!
Refer to Safety chapters.12.1  Notes on cleaning
• Clean the front of the appliance with a
soft cloth with warm water and a
cleaning agent.
• To clean metal surfaces, use a dedicated cleaning agent.
• To clean the bottom side in case of limestone residual, use some drops ofvinegar.
• Clean the appliance interior after
each use. Fat accumulation or otherfood remains may result in a fire. The
risk is higher for the grill pan.
• Clean stubborn dirt with a special oven cleaner.
• Clean all accessories after each use and let them dry. Use a soft cloth withwarm water and a cleaning agent.
• If you have nonstick accessories, do
not clean them using aggressive
agents, sharp-edged objects or a dishwasher. It can cause damage to
the nonstick coating.12.2  Recommended cleaning
products
Do not use abrasive sponges or
aggressive detergents. It can cause
damage to the enamel and the stainless
steel parts.
You can buy our products at
www.aeg.com/shop and at the best retailer shops.
12.3  Removing the shelf
supports
Before maintenance, make sure that the
appliance is cool. There is a risk of burns.
ENGLISH61  
						

							To clean the appliance, remove the shelf
supports.
1. Pull carefully the supports up and out
of the front catch.
2. Pull the front end of the shelf support
away from the side wall.
3. Pull the supports out of the rear
catch.
Install the shelf supports in the opposite
sequence.
12.4  Steam Cleaning
Remove as much dirt as possible
manually.
Remove the accessories and the shelf support to clean the side walls.
The steam cleaning functions support
the steam cavity cleaning of the
appliance.
For a better performance
you should start the cleaning
function when the appliance
is cool.The specified time is related
to the duration of the
function and does not
include the time required for
cleaning of the cavity by the
user.
When the steam cleaning function is
active, the lamp is off.
1. Fill the water drawer to the maximum
level.
2. Choose the steam cleaning function
in the menu: Cleaning.
Steam Cleaning  - the duration of the
function is around 30 minutes. a) Activate the function.
b) An acoustic signal sounds when
the programme is completed.
c) Touch the display to deactivate
the signal.
Steam Cleaning Plus  - the duration
of the function is around 75 minutes. a) Spray a suitable detergent
uniformly in the oven cavity on
both enamel and steel parts.
Before you start the cleaning
procedure, make sure that the
appliance is cold.
b) Activate the function.
After around 50 minutes an
acoustic signal sounds when the
first part of the programme is
completed.This is not the end of
the cleaning
procedure. Follow
the message in the
display to complete
the cleaning.
c) Wipe the internal surface of the
appliance with a non-abrasive
surface care sponge. You can use
warm water or oven detergents
to clean the cavity.
d) The final part of the procedure
starts. The duration of this stage
is around 25 minutes.
3. Wipe the internal surface of the
appliance with a non-abrasive surface
care sponge. You can use warm
water to clean the cavity.
4. Remove the remaining water from
the water drawer.
After cleaning keep the appliance door
open for approximately 1 hour. Wait until
the appliance is dry. To speed up the
drying you can heat up the appliance
with hot air at temperature 150 °C for
approximately 15 minutes. You can get
maximum effects of the cleaning function
if you manually clean the appliance
immediately after the function ends.
12.5  Cleaning Reminder
This function reminds you that the
cleaning is necessary and that you should
www.aeg.com6223
1     
						

							perform the function: Steam CleaningPlus.
You can enable / disable the function:
Cleaning Reminder in the menu: Basic
Settings.12.6  Cleaning the water
drawer
Remove the water drawer from the
appliance.
1. Remove the lid of the water drawer.
Lift the cover in correspondence with
the protrusion in the rear.
2. Remove the wave-breaker. Pull it
away from the drawer body until it
snaps out.
3. Wash the water drawer parts with
your hands. Use tap water and soap. 
Do not use abrasive
sponges. Do not put
water drawer inside a
dish washer.
After you clean the water drawer parts, reassemble the water drawer.
1. Snap in the wave-breaker. Push it
into the drawer body.
2. Assemble the lid. First insert the front
snap and then push it against the
drawer body.
3. Insert the water drawer inside the
appliance.
4. Push the water drawer towards the
oven until it latches.12.7  Steam generation system
- Descaling
When the steam generator operates,
there is an accumulation and deposition
of limestone inside because of calcium contents in the water. This can have anegative effect on the steam quality, onthe performance of the steam generator
and on the food quality. To prevent this,
clean the steam generation circuit from
residual stone.
Remove all accessories.
Select the function from the menu:
Cleaning. The user interface will guide
you through the procedure.
The duration of the complete procedure
is about 2 hours.
The light in this function is off.
1. Put the grill- / roasting pan on the
first shelf position.
2. Put 250 ml of the descaling agent in
the water drawer.
3. Fill the remaining part of the water
drawer with water to the maximum
level.
4. Fit the water drawer in the appliance.
5. Activate the procedure
The duration of this part is
around 1 hour 40 minutes.
6. After the end of the first part, empty
the grill- / roasting pan and put it on
the first shelf position again.
7. Fill the water drawer with fresh water.
Make sure there is no remaining cleaning solution inside the water
drawer.
8. Fit the water drawer in the appliance.
9. Activate the second part of the
procedure to rinse the steam
generation circuit.
The duration of this part is
around 35 minutes.
Remove the grill- / roasting pan after the
end of the procedure.
ENGLISH63XAM  XAM
XAM    
						

							If the function: Descaling is
not performed in the correct
way, the display will show a
message to repeat it.
If the appliance is humid and wet, wipe it out with a dry cloth. Let the appliance
dry fully with the door open.
12.8  Descaling reminder
There are two descaling reminders which
remind you to perform the function:
Descaling. These reminders activate
each time you switch on the appliance.
The soft reminder reminds and
recommends you to perform the
descaling cycle.
The hard reminder obligates you to perform the descaling.
If you do not descale the
appliance when the hard
reminder is on, you cannot
use the steam functions.
You cannot disable the
descaling reminder.12.9  Steam generation system
- Rinsing
Remove all accessories.
Select the function from the menu:
Cleaning. The user interface will guide
you through the procedure.
The duration of the function is around 30
minutes.
The light in this function is off.
1. Put the baking tray on the first shelf
position.
2. Fill the water drawer with fresh water.
3. Activate the function.
Remove the baking tray after the end of the procedure.
12.10  Removing and installing
the door
You can remove the door and the
internal glass panels to clean it. The
number of glass panels is different for
different models.
WARNING!
Be careful when you remove
the door from the appliance.
The door is heavy.
1. Open the door fully.
2. Fully press the clamping levers (A) on
the two door hinges.
3. Close the oven door to the first
opening position (approximately 70°
angle).
4. Hold the door with one hand on each
side and pull it away from the
appliance at an upwards angle.
5. Put the door with the outer side
down on a soft cloth on a stable
surface. This is to prevent scratches.
6. Hold the door trim (B) on the top
edge of the door at the two sides
and push inwards to release the clip
seal.
7. Pull the door trim to the front to
remove it.
8. Hold the door glass panels on their
top edge one by one and pull them
up out of the guide.
9. Clean the glass panel with water and
soap. Dry the glass panel carefully.
www.aeg.com64   AA 1
2
B   
						

							When the cleaning is completed, install
the glass panels and the door. Do the
above steps in the opposite sequence.
Install the smaller panel first, then the
larger.12.11  Replacing the lamp
Put a cloth on the bottom of the interior
of the appliance. It prevents damage to the lamp glass cover and the cavity.
WARNING!
Danger of electrocution!
Disconnect the fuse before
you replace the lamp.
The lamp and the lamp glass
cover can be hot.
1. Deactivate the appliance.
2. Remove the fuses from the fuse box
or deactivate the circuit breaker.
The top lamp
1. Turn the lamp glass cover
counterclockwise to remove it.
2. Remove the metal ring and clean the
glass cover.
3. Replace the lamp with a suitable 300
°C heat-resistant lamp.
4. Attach the metal ring to the glass
cover.
5. Install the glass cover.The side lamp
1.Remove the left shelf support to get
access to the lamp.
2. Use a Torx 20 screwdriver to remove
the cover.
3. Remove and clean the metal frame
and the seal.
4. Replace the lamp with a suitable 300
°C heat-resistant lamp.
5. Install the metal frame and the seal.
Tighten the screws.
6. Install the left shelf support.
13.  TROUBLESHOOTINGWARNING!
Refer to Safety chapters.13.1  What to do if...ProblemPossible causeRemedyYou cannot activate or oper-
ate the oven.The oven is not connected
to an electrical supply or it is
connected incorrectly.Check if the oven is correctly
connected to the electrical
supply (refer to the connec-
tion diagram if available).The oven does not heat up.The oven is deactivated.Activate the oven.The oven does not heat up.The necessary settings are
not set.Make sure that the settings
are correct.ENGLISH65    
						

							ProblemPossible causeRemedyThe oven does not heat up.The Child Lock is on.Refer to "Using the Child
Lock".The oven does not heat up.The fuse is blown.Make sure that the fuse is
the cause of the malfunction.
If the fuse is blown again
and again, contact a quali-
fied electrician.The lamp does not operate.The lamp is defective.Replace the lamp.The display shows error mes-
sage "F....."Electronic error.Contact an Authorised Serv-
ice Centre.Steam and condensation
settle on the food and in the
cavity of the oven.You left the dish in the oven
for too long.Do not leave the dishes in
the oven for longer than 15 -
20 minutes after the cooking
process ends.The appliance does not re-
tain the water drawer after
you insert it.You did not assemble the lid
of the water drawer correct-
ly.Assemble the lid of the wa-
ter drawer correctly.Water comes out of the wa-
ter drawer after you carry it
or put it inside the appli-
ance.You did not assemble the lid
of the water drawer correct-
ly.Assemble the lid of the wa-
ter drawer correctly.Water comes out of the wa-
ter drawer after you carry it
or put it inside the appli-
ance.You did not assemble the
wave-breaker correctly.Assemble the wave-breaker
in the body of the water
drawer correctly.The appliance does not re-
tain the water drawer after
you push it on the cover.You did not fully press the
water drawer body.Insert the water drawer body
in the appliance by pushing
it until it reaches to the end.The water drawer is difficult
to clean.You did not remove the lid
and the wave-breaker.Refer to "Cleaning the water
drawer".The descaling procedure is
interrupted before it finishes.There was a power cut.Repeat the procedure.The descaling procedure is
interrupted before it finishes.The function was stopped by
the user.Repeat the procedure.There is no water inside the
grill- / roasting pan after the
descaling procedure.You did not fill the water
drawer to the maximum lev-
el.Check if the a descaling
agent / water is present in
the water drawer body.
Repeat the procedure.www.aeg.com66 
						

							ProblemPossible causeRemedyThere is dirty water on the
bottom of the cavity after
the descaling cycle.The grill- / roasting pan is on
a wrong shelf position.Remove the residual water
and the descaling agent
from the bottom of the
oven. Put the grill- / roasting
pan on the first shelf posi-
tion.The cleaning function is in-
terrupted before it finishes.There was a power cut.Repeat the procedure.The cleaning function is in-
terrupted before it finishes.The function was stopped by
the user.Repeat the procedure.There is too much water on
the bottom of the cavity af-
ter the end of the cleaning
function.You sprayed too much de-
tergent in the appliance be-
fore the activation of the
cleaning cycle.Cover all parts of the cavity
with a thin layer of the deter-
gent. Spray the detergent
evenly.There is no good perform-
ance of the cleaning proce-
dure.The initial oven cavity tem-
perature of the steam clean-
ing function was too high.Repeat the cycle. Run the cy-
cle when the appliance is
cold.There is no good perform-
ance of the cleaning proce-
dure.You did not remove the side
grids before the start of the
cleaning procedure. They
can transfer heat to the walls
and decrease the perform-
ance.Remove the side grids from
the appliance and repeat the
function.There is no good perform-
ance of the cleaning proce-
dure.You did not remove the ac-
cessories from the appliance
before the start of the clean-
ing procedure. They can
compromise the steam cycle
and decrease the perform-
ance.Remove the accessories
from the appliance and re-
peat the function.13.2  Service data
If you cannot find a solution to the
problem yourself, contact your dealer or
an Authorised Service Centre.
The necessary data for the service centre
is on the rating plate. The rating plate ison the front frame of the appliance
cavity. Do not remove the rating plate
from the appliance cavity.We recommend that you write the data here:Model (MOD.).........................................Product number (PNC).........................................Serial number (S.N.).........................................ENGLISH67 
						

							14. ENERGY EFFICIENCY14.1  Product Fiche and information according to EU 65-66/2014Supplier's nameAEGModel identificationBS836680KMEnergy Efficiency Index92.9Energy efficiency classAEnergy consumption with a standard load, conven-
tional mode0.93 kWh/cycleEnergy consumption with a standard load, fan-forced
mode0.79 kWh/cycleNumber of cavities1Heat sourceElectricityVolume71 lType of ovenBuilt-In OvenMass45.5 kgEN 60350-1 - Household electric cooking
appliances - Part 1: Ranges, ovens, steam
ovens and grills - Methods for measuring performance.14.2  Energy savingThe appliance contains
features which help you save
energy during everyday
cooking.General hints
Make sure that the oven door is closed
properly when the appliance operates
and keep it closed as much as possible
during the cooking.
Use metal dishes to improve energy
saving.
When possible, do not preheat the oven before you put the food inside.
When the cooking duration is longer
than 30 minutes, reduce the oven
temperature to minimum 3 - 10 minutes
before the end of the cooking time,
depending on the duration of the
cooking. The residual heat inside the
oven will continue to cook.
Use the residual heat to warm up other
dishes.Cooking with fan
When possible, use the cooking
functions with fan to save energy.
Residual heat
If a programme with the Duration or End
Time selection is activated and the cooking time is longer than 30 minutes,
the heating elements deactivate
automatically 10% faster in some oven
functions.
The fan and lamp continue to operate.
Keep food warm
Choose the lowest possible temperature setting to use residual heat and keep ameal warm. The display shows theresidual heat indicator or temperature.
Cooking with the lamp off
Deactivate the lamp during cooking and
activate only when you need it.
www.aeg.com68  
						

							15. ENVIRONMENTAL CONCERNSRecycle the materials with the symbol .
Put the packaging in applicable
containers to recycle it. Help protect the
environment and human health and to recycle waste of electrical and electronic
appliances. Do not dispose appliancesmarked with the symbol  with the
household waste. Return the product to
your local recycling facility or contact
your municipal office.
*
ENGLISH69   
						

							www.aeg.com70