AEG Scs 91800 F0 User Manual

							• do not exceed the storage period in-
dicated by the food manufacturer.
5. CARE AND CLEANING
CAUTION!
Unplug the appliance before car-
rying out any maintenance oper-
ation.
This appliance contains hydrocar-
bons in its cooling unit; mainte-
nance and recharging must
therefore only be carried out by
authorized technicians.
5.1 Periodic cleaning
The equipment has to be cleaned regu-
larly:
• clean the inside and accessories with
lukewarm water and some neutral
soap.
• regularly check the door seals and
wipe clean to ensure they are clean
and free from debris.
• rinse and dry thoroughly.
Do not pull, move or damage
any pipes and/or cables inside
the cabinet.
Never use detergents, abrasive
powders, highly perfumed clean-
ing products or wax polishes to
clean the interior as this will dam-
age the surface and leave a
strong odour.Clean the condenser (black grill) and the
compressor at the back of the appliance
with a brush. This operation will improve
the performance of the appliance and
save electricity consumption.
Take care of not to damage the
cooling system.
Many proprietary kitchen surface clean-
ers contain chemicals that can attack/
damage the plastics used in this appli-
ance. For this reason it is recommended
that the outer casing of this appliance is
only cleaned with warm water with a little
washing-up liquid added.
After cleaning, reconnect the equipment
to the mains supply.
ENGLISH11
 
						

							5.2 Defrosting of the refrigerator
Frost is automatically eliminated from
the evaporator of the refrigerator com-
partment every time the motor compres-
sor stops, during normal use. The de-
frost water drains out through a trough
into a special container at the back of
the appliance, over the motor compres-
sor, where it evaporates.
Periodically clean the defrost water drain
hole in the middle of the refrigerator
compartment channel to prevent the wa-
ter overflowing and dripping onto the
food inside. Use the special cleaner pro-
vided, which you will find already inser-
ted into the drain hole.
5.3 Defrosting the freezer
A certain amount of frost will always form
on the freezer shelves and around the
top compartment.
Defrost the freezer when the frost layer
reaches a thickness of about 3-5 mm.
About 12 hours prior to defrost-
ing, set the Temperature regula-
tor toward higher settings, in or-
der to build up sufficient chill re-
serve for the interruption in oper-
ation.
12www.aeg.com
 
						

							To remove the frost, follow the instruc-
tions below:
1.Switch off the appliance.
2.Remove any stored food, wrap it in
several layers of newspaper and put
it in a cool place.
CAUTION!
Do not touch frozen goods with
wet hands. Hands can freeze to
the goods.
3.Leave the door open and insert the
plastic scraper in the appropriate
seating at the bottom centre, plac-
ing a basin underneath to collect the
defrost water.
In order to speed up the defrost-
ing process, place a pot of warm
water in the freezer compart-
ment. In addition, remove pieces
of ice that break away before de-
frosting is complete.
4.When defrosting is completed, dry
the interior thoroughly and keep the
scraper for future use.
5.Switch on the appliance.
6.After two or three hours, reload the
previously removed food into the
compartment.
Never use sharp metal tools to scrape
off frost from the evaporator as you
could damage it.
Do not use a mechanical device or any
artificial means to speed up the thawing
process other than those recommended
by the manufacturer.
A temperature rise of the frozen food
packs, during defrosting, may shorten
their safe storage life.
5.4 Periods of non-operation
When the appliance is not in use for
long periods, take the following precau-
tions:
•disconnect the appliance from elec-
tricity supply
• remove all food• defrost (if foreseen) and clean the ap-
pliance and all accessories
• leave the door/doors ajar to prevent
unpleasant smells.
If the cabinet will be kept on, ask some-
body to check it once in a while to pre-
vent the food inside from spoiling in
case of a power failure.
ENGLISH13
 
						

							6. WHAT TO DO IF…
WARNING!
Before troubleshooting, discon-
nect the mains plug from the
mains socket.
Only a qualified electrician or
competent person must do the
troubleshooting that is not in this
manual.
ProblemPossible causeSolution
The appliance is
noisyThe appliance is not sup-
ported properlyCheck if the appliance
stands stable (all the four
feet should be on the
floor)
The appliance does
not operate. The
lamp does not oper-
ate.The appliance is switched
off.Switch on the appliance.
 The mains plug is not
connected to the mains
socket correctly.Connect the mains plug to
the mains socket correctly.
 The appliance has no
power. There is no volt-
age in the mains socket.Connect a different electri-
cal appliance to the mains
socket.
Contact a qualified electri-
cian.
The lamp does not
work.The lamp is in stand-by.Close and open the door.
 The lamp is defective.Refer to "Replacing the
lamp".
The buzzer sounds.
The Alarm light
flashing.The temperature in the
freezer is too high.Refer to "High Tempera-
ture Alarm".
The compressor op-
erates continually.The temperature is not
set correctly.Set a higher temperature.
 The door is not closed
correctly.Refer to "Closing the
door".
 The door has been
opened too frequently.Do not keep the door
open longer than necessa-
ry.
 The product temperature
is too high.Let the product tempera-
ture decrease to room
temperature before stor-
age.
 The room temperature is
too high.Decrease the room tem-
perature.
14www.aeg.com
 
						

							ProblemPossible causeSolution
The compressor
does not start imme-
diately after press-
ing the FROSTMAT-
IC or COOLMATIC
button, or after
changing the tem-
perature.This is normal, no error
has occurred.The compressor starts af-
ter a period of time.
Water flows on the
rear plate of the re-
frigerator.During the automatic de-
frosting process, frost de-
frosts on the rear plate.This is correct.
Water flows into the
refrigerator.The water outlet is clog-
ged.Clean the water outlet.
 Products prevent that wa-
ter flows into the water
collector.Make sure that products
do not touch the rear
plate.
The temperature in
the appliance is too
low/high.The temperature regula-
tor is not set correctly.Set a higher/lower temper-
ature.
 The door is not closed
correctly.Refer to "Closing the
door".
 The product temperature
is too high.Let the product tempera-
ture decrease to room
temperature before stor-
age.
 Many products are stored
at the same time.Store less products at the
same time.
The temperature in
the refrigerator is
too high.There is no cold air circu-
lation in the appliance.Make sure that there is
cold air circulation in the
appliance.
The temperature in
the freezer is too
high.Products are too near to
each other.Store products so that
there is cold air circulation.
There is too much
frost.Food is not wrapped cor-
rectly.Wrap the food correctly.
 The door is not closed
correctly.Refer to "Closing the
door".
 The temperature regula-
tor is not set correctly.Set a higher temperature.
Upper or lower
square is shown in
the temperature Dis-
play.An error has occurred in
measuring the tempera-
ture.Call your service represen-
tative (the cooling system
will continue to keep food
products cold, but temper-
ature adjustment will not
be possible).
ENGLISH15
 
						

							ProblemPossible causeSolution
dEMo appears on
the Display.  The appliance is in dem-
onstration mode (dEMo).Keep pressed approxi-
mately 10 sec. the OK but-
ton since a long sound of
buzzer is heard and the
Display shut off for a short
while: appliance start
works regularly.    
6.1 Replacing the lamp
The appliance is equipped with a long-
life LED interior light.
Only service is allowed to replace the
lighting device. Contact your Service
Center.
6.2 Closing the door
1.Clean the door gaskets.
2.If necessary, adjust the door. Refer
to "Installation".
3.If necessary, replace the defective
door gaskets. Contact the Service
Center.
7. INSTALLATION
7.1 Positioning
WARNING!
If you are discarding an old appli-
ance that has a lock or catch on
the door, you must ensure that it
is made unusable to prevent
young children being trapped in-
side.
The appliance shall have the
plug accessible after installation.
Install this appliance at a location where
the ambient temperature corresponds to
the climate class indicated on the rating
plate of the appliance:
Cli-
mate
classAmbient temperature
SN+10°C to + 32°C
N+16°C to + 32°C
ST+16°C to + 38°C
Cli-
mate
classAmbient temperature
T+16°C to + 43°C
7.2 Electrical connection
Before plugging in, ensure that the volt-
age and frequency shown on the rating
plate correspond to your domestic pow-
er supply.
The appliance must be earthed. The
power supply cable plug is provided
with a contact for this purpose. If the do-
mestic power supply socket is not earth-
ed, connect the appliance to a separate
earth in compliance with current regula-
tions, consulting a qualified electrician.
The manufacturer declines all responsi-
bility if the above safety precautions are
not observed.
This appliance complies with the E.E.C.
Directives.
16www.aeg.com
 
						

							7.3 Ventilation requirements
5 cmmin.
200 cm2
min.
200 cm2
The airflow behind the appliance must
be sufficient.
8. NOISES
There are some sounds during normal
running (compressor, refrigerant circula-
tion).
BRRR!HISSS!
CLICK!
BLUBB!
CRACK!
SSSRR
R!
OK
CLICK!CLICK!SSSRRR!SSSRRR!
ENGLISH17
 
						

							BRRR!BRRR!HISSS!HISSS!
BLUBB!BLUBB!CRACK!CRACK!
9. TECHNICAL DATA
   
Dimension of the recess  
 Height1780 mm
 Width560 mm
 Depth550 mm
Rising Time 24 h
Voltage 230-240 V
Frequency 50 Hz
The technical information are situated in
the rating plate on the internal left side
of the appliance and in the energy label.
18www.aeg.com
 
						

							10. ENVIRONMENT CONCERNS
Recycle the materials with the
symbol  . Put the packaging in
applicable containers to recycle it.
Help protect the environment and
human health and to recycle waste
of electrical and electronicappliances. Do not dispose
appliances marked with the symbol with the household waste. Return the
product to your local recycling
facility or contact your municipal
office.
ENGLISH19
 
						

							INHALT
1.SICHERHEITSHINWEISE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  21
2.BEDIENFELD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  23
3.TÄGLICHER GEBRAUCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  27
4.PRAKTISCHE TIPPS UND HINWEISE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  28
5.REINIGUNG UND PFLEGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  30
6.WAS TUN, WENN … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  33
7.MONTAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  36
8.GERÄUSCHE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  36
9.TECHNISCHE DATEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  38
10.UMWELTTIPPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  38
FÜR PERFEKTE ERGEBNISSE
Danke, dass Sie sich für dieses AEG Produkt entschieden haben. Wir haben es geschaffen,
damit Sie viele Jahre von seiner ausgezeichneten Leistung und den innovativen Technologien,
die Ihnen das Leben erleichtern, profitieren können. Es ist mit Funktionen ausgestattet, die in
gewöhnlichen Geräten nicht vorhanden sind. Nehmen Sie sich ein paar Minuten Zeit zum
Lesen, um seine Vorzüge kennen zu lernen.
Besuchen Sie uns auf unserer Website, um:
Anwendungshinweise, Prospekte, Fehlerbehebungs- und Service-Informationen zu
erhalten:
www.aeg.com
Ihr erworbenes Produkt zu registrieren, um den besten Service dafür zu
gewährleisten:
www.aeg.com/productregistration
Zubehör, Verbrauchsmaterial und Original-Ersatzteile für Ihr Gerät zu erwerben:
www.aeg.com/shop
KUNDENDIENST UND -BETREUUNG
Bitte verwenden Sie ausschließlich Original-Ersatzteile für Ihre Produkte.
Halten Sie folgende Angaben bereit, wenn Sie sich an den Kundendienst wenden
(diese Informationen finden Sie auf dem Typenschild): Modell, Produktnummer (PNC),
Seriennummer.
Warnungs-/ Sicherheitshinweise.
Allgemeine Hinweise und Ratschläge
Hinweise zum Umweltschutz
Änderungen vorbehalten.
20www.aeg.com