AEG S 75358 Kg3 User Manual

HELPFUL HINTS AND TIPS
Normal Operating Sounds
• You may hear a faint gurgling and a bubbling sound when the refrigerant is pumped
through the coils or tubing. This is correct.
• When the compressor is on, the refrigerant is being pumped around and you will hear a
whirring sound and a pulsating noise from the compressor. This is correct.
• The thermic dilatation might cause a sudden cracking noise. It is natural, not dangerous
physical phenomenon. This is correct.
Hints for energy saving
• Do not open...

• wrap up the food in aluminium foil or polythene and make sure that the packages are
airtight;
• do not allow fresh, unfrozen food to touch food which is already frozen, thus avoiding a
rise in temperature of the latter;
• lean foods store better and longer than fatty ones; salt reduces the storage life of food;
• water ices, if consumed immediately after removal from the freezer compartment, can
possibly cause the skin to be freeze burnt;
• it is advisable to show the freezing in date on each...

After cleaning, reconnect the equipment to the mains supply.
Replacing the carbon air filter
To get the best performance the carbon air filter should be changed once every six months.
New active air filters can be purchased from your local dealer.
Refer to Installation of the carbon air filter for the instructions.
Defrosting
Your appliance is frost free. This means that there is no buildup of frost when it is in opera-
tion, neither on the internal walls nor on the foods.
The absence of frost is due to...

ProblemPossible causeSolution
Water flows into the re-
frigerator.The water outlet is clogged.Clean the water outlet.
 Products prevent that water
flows into the water collector.Make sure that products do not
touch the rear plate.
Water flows on the
ground.The melting water outlet does
not flow in the evaporative tray
above the compressor.Attach the melting water outlet
to the evaporative tray.
There is too much frost
and ice.Products are not wrapped prop-
erly.Wrap the products better.
 The door is not...

Replacing the lamp
CAUTION!
Disconnect the plug from the mains socket.
1. Pull outwards the hook of the lamp cover.
2. Remove the lamp cover.
3. Replace the lamp with one of the same power
(the maximum power is shown on the light
bulb cover).
4. Install the lamp cover.
5. Connect the plug to the mains socket.
6. Open the door. Make sure that the light
comes on.
Closing the door
1. Clean the door gaskets.
2. If necessary, adjust the door. Refer to Installation.
3. If necessary, replace the defective door...

Climate classAmbient temperature
SN+10°C to + 32°C
N+16°C to + 32°C
ST+16°C to + 38°C
T+16°C to + 43°C
Location
The appliance should be installed well away from
sources of heat such as radiators, boilers, direct
sunlight etc. Ensure that air can circulate freely
around the back of the cabinet. To ensure best
performance, if the appliance is positioned below
an overhanging wall unit, the minimum distance
between the top of the cabinet and the wall unit
must be at least 100 mm . Ideally, however, the...

Rear spacers
You can find the two spacers in the bag with doc-
umentation.
Do these steps to install the spacers:
1. Release the screw.
2. Engage the spacer below the screw.
3. Turn the spacer to the right position.
4. Tighten again the screws.
Levelling
When placing the appliance ensure that it stands
level. This can be achieved by two adjustable feet
at the bottom in front.
2
431
Installation17
 

Removing the shelf holders
Your appliance is equipped with shelf retainers
that make it possible to secure the shelves during
transportation.
To remove them proceed as follows:
1. Move the shelf holders in the direction of the
arrow (A).
2. Raise the shelf from the rear and push it for-
ward until it is freed (B).
3. Remove the retainers (C).
Installation of the carbon air filter
The carbon air filter is an active carbon filter which absorbs bad odours and permits to
maintain the best flavour and aroma...

1. Open the doors. Unscrew the middle
hinge (m2). Remove the plastic spacer
(m1).
2. Remove the spacer (m6) and move to
the other side of the hinge pivot (m5).
3. Remove the doors.
4. Remove the left-hand cover pin of the
middle hinge (m3,m4) and move to the
other side.
5. Fit the pin of the middle hinge (m5) into
the left-hand hole of the lower door.
6. Remove using a tool the cover (b1). Un-
screw the lower hinge pivot (b2) and the
spacer (b3) and place them on the op-
posite side.
7. Re-insert the...

10. Remove the handle. Unscrew the top
handle bracket from the handle rod (h1).
Unscrew the bottom handle bracket
from the door (h2)
Unscrew the top handle bracket from
the door (h3).
11. Install the handle in the opposite side.
Re-screw the handle bracket on the
door (h4). Turn the handle bracket with
the handle and screw them to the door
(h5) and the fitted handle bracket (h6).
12. Re-insert the lower door on the lower
hinge pivot (b2).
13. Insert the middle hinge (m2) into the
left drill of the lower...