AEG Lavamat 72650 User Manual

Installation
Unpacking
All transit bolts and packing must be removed before using the appliance.
You are advised to keep all transit devices so that they can be refitted if the
machine ever has to be transported again.
1.After removing all the packaging, carefully lay
machine on it’s back to remove the
polystyrene base from the bottom.
2.Remove the power supply cable and the
draining hose from the hose holders on the rear of the
appliance.
3.With the provided spanner unscrew and
remove the central rear...

4.Unscrew and remove the two large rear bolts B
and the six smaller bolts C.
5.Remove the bracket Dand tighten up the six
smaller bolts C. Slide out the relevant plastic
spacerE.
6.Open the porthole, take out the inlet hose from the
drum and remove the polystyrene block fitted on the
door seal.
7.Fill the smaller upper hole and the two large ones with
the corresponding plastic plug caps supplied in the bag
containing the instruction booklet.
8.Connect the water inlet hose as described under the
paragraph...

Positioning and levelling
Install the machine on a flat hard floor.
Make sure that air circulation around the machine is not impeded by carpets,
rugs etc.
Before placing it on small tiles, apply a rubber coating.
Never try to correct any unevenness in the floor by
putting pieces of wood, cardboard or similar
materials under the machine.
If it is impossible to avoid positioning the machine
next to a gas cooker or coal-burning stove, an
insulating panel covered with aluminium foil on the
side facing the...

Do not place the inlet hose downwards. Angle
the hose to the left or right depending on the
position of your water tap.
3.Set the hose correctly by loosening the ring nut.
After positioning the inlet hose, be sure to tighten
the ring nut again to prevent leaks.
4.Connect the hose to a tap with a 3/4” thread.
Always use the hose supplied with the appliance.
Installation should comply with local water authority and building regulations
requirements. A minimum water pressure of 0.05 MPa is required for...

the drain pipe must be larger than the outside diameter of the drain hose.
The drain hose must not be kinked.
Important!
The drain hose may be extended to a maximum of 4 metres. An additional drain hose and
joining piece is available from your local Service Centre.
Electrical connection
This machine is designed to operate on a 230 V, single-phase, 
50 Hz supply.
Check that your domestic electrical installation can take the maximum load
required (2.2 kW), also taking into account any other appliances in...

Enviroment concerns
Packaging materials
The materials marked with the symbol  are recyclable.
>PEPSPP

European Guarantee
This appliance is guaranteed by Electrolux in each of the countries listed at the
back of this user manual, for the period specified in the appliance guarantee
orotherwise by law. If you move from one of these countries to another of the
countries listed, the appliance guarantee will move with you subject to the
following qualifications:
The appliance guarantee starts from the date you first purchased the appliance
which will be evidenced by production of a valid purchase document...

48Customer service centres
www.electrolux.com
!!
Albania+35 5 4 261 450Rr. Pjeter Bogdani Nr. 7 Tirane
Belgique/België/Belgien+32 2 363 04 44Bergensesteenweg 719, 1502 Lembeek
Česká republika+420 2 61 12 61 12Budějovická 3, Praha 4, 140 21
Danmark+45 70 11 74 00Sjællandsgade 2, 7000 Fredericia
Deutschland+49 180 32 26 622Muggenhofer Str. 135, 90429 Nürnberg
Eesti+37 2 66 50 030Mustamäe tee 24, 10621 Tallinn 
España+34 902 11 63 88Carretera M-300, Km. 29,900 Alcalá de Henares  Madrid...

49
192998640 gb.qxd  13/08/2007  17.39  Pagina  49
 

50
192998640 gb.qxd  13/08/2007  17.39  Pagina  50