ADT Security Services Simon 3 Owner Manual

Simon Security System16
Option 01 - Status Beeps 
Add this option to enable panel beeps. Status beeps are any beeps (including chime 
beeps) that come from the panel. See “Status Beeps”. 
1. Open panel cover. Panel announces, Use numbered keys to enter ID. 
2. Enter Access Code using the numbered keys. Panel announces, Please select from 
Start Menu.
3. Press Add from the Start menu. Panel announces, Select from main menu.
4. Press Option #. Panel announces, Option 1, press again for next option or done...

Simon Security System17
Delete turns off this option and Latchkey cannot be enabled when the panel is armed.
1. Open panel cover. Panel announces, Use numbered keys to enter ID. 
2. Enter Access Code using the numbered keys. Panel announces, Please select from 
Start Menu.
3. Press Delete from the Start menu. Panel announces, Select from main menu
4. Press Option #. Panel announces, Option 1, press again for next option or done to 
select.
5. Press 03. Panel announces, Option 3, press again for next...

Simon Security System18
Delete disables sensor activated light lockout stop time. The panel will turn on a light 
activated by a sensor at all times if sensor activated lights are enabled.
1. Open panel cover. Panel announces, Use numbered keys to enter ID. 
2. Enter Access Code using the numbered keys. Panel announces, Please select from 
Start Menu.
3. Press Delete from the Start menu. Panel announces, Select from main menu
4. Press Option #. Panel announces, Option 1, press again for next option or...

Simon Security System19
2. Enter Access Code using the numbered keys. Panel announces, Please select from 
Start Menu.
3. Press Delete from the Start menu. Panel announces, Select from main menu
4. Press Option #. Panel announces, Option 1, press again for next option or done to 
select.
5. Press 42. Panel announces, Option 42, press again for next option or done to delete.
6. Press DONE. Panel announces, Option 42 deleted.
Option 43 - Pager Phone Number
Add enables the pager phone number and allows you...

Simon Security System20
AC Power Failures - An AC power failure is called in after loss of power. To 
avoid false alarms, your installer has programmed the panel to wait at least a few 
minutes (or up to several hours) before calling in.
AC Power Restore - A restore will be reported when power is restored.
Alarms - Alarm reports include: Emergency, Intrusion, and Fire.
Option 55: Status Sounds
Add allows you to set the volume for status sounds, such as arming beeps, trouble 
beeps, and status beeps....

Simon Security System21
4. Press Option #. Panel announces, Option 1, press again for next option or done to 
select.
5. Press 81. Panel announces, Option 81, press again for next option or done to delete.
6. Press DONE. Panel announces, Option 81 deleted.
Option 82: Cooling Set Point
When this option is on you can set a temperature that will automatically turn the air con-
ditioner on if the temperature rises above the set temperature. The commands are set 
through the control panel, to the RF...

Simon Security System22
System Battery Failure
This condition occurs if the emergency backup battery has failed. Status beeps will 
start and the SYSTEM STATUS button will light. Press the SYSTEM STATUS but-
ton to hear the trouble message. If your AC power is not working, your security sys-
tem will shut down once the battery has failed. If the condition does not clear after AC 
power has been restored and 24 hours have passed, call your security system dealer.
Sensor Failure
This condition occurs if a...

Simon Security System23
System Access Alarm
The panel cover was opened while the system was armed. The system will call the cen-
tral monitoring station to report a tamper alarm.
TestingAs an added safeguard, there are system tests you should do yourself on a regular basis. 
It is recommended that you test your system weekly. 
Testing Sensors 
You can test sensors one at a time to make sure they are sending strong signals to the 
panel. You should test the security system at least once a week.


To...

Simon Security System24
Testing Communication 
Communication between your system, the central monitoring station and your pager 
should be tested at least once per week to make sure you have the proper telephone 
connection.


To perform a phone test:
1. Open the panel cover.
2. Enter the master access code.
3. Press the Te s t button twice. The panel will announce Phone test, press again to 
change or done to select.
4. Press the DONE button.
Note  
If your system is not con-
nected to a central...

Simon Security System25
 If sirens are not placed within hearing range of persons sleeping, in remote parts of 
the premises, or if they are placed behind doors or other obstacles.
 If intruders gain access through unprotected points of entry or areas where sensors 
have been bypassed.
 If intruders have the technical means of bypassing, jamming, or disconnecting all 
or part of the system.
 If power to sensors is inadequate or disconnected.
 If freeze or any environmental sensors are not located in...