ADT Security Services Simon 3 Owner Manual

Simon Security System6
The Home Control buttons are used to monitor activity within and around the home. 
They are not used for intrusion protection. If any of the Home Control buttons are 
pressed and a sensor or module is not associated (programmed) with this feature the 
panel will announce, Function not available.
Chime Doors
Chime Doors is used to signal (chime) when a protected door is opened while the sys-
tem is disarmed. The panel will announce the door that has been tripped and chime 
twice...

Simon Security System7
Sensor Activated Lights
Turn on designated lights (with Lamp Modules) when a sensor is tripped. You can pro-
gram lockout times when Sensor Activated Lights won’t be active (see Programming 
Options 36 and 37).


Turn Sensor Activated Lights On:
1. System must be disarmed. Press Sensor Lights button.
Panel will announce, sensor activated lights on. Sensor Lights button will be lit.


Turn Sensor Activated Lights Off:
1. Press Sensor Lights button.
Panel will announce, sensor...

Simon Security System8
Status Beeps
Note  
You may receive a different 
number of status beeps if 
buttons are pressed quicklyStatus beeps are used to indicate key presses, status, and problems with the system. 
They can be enabled or disabled (see  “Options”). The following table describes status 
beep activity.
.
Alarm Sirens and Lamp Modules
Exterior and interior sirens make 3 different alarm sounds on the premises, each indi-
cating a different type of alarm. Sirens are programmed by the installer to...

Simon Security System9
Panel Indicator Lights
Use the following table to understand the panel indicator lights.
Numeric Pager
You may program your security system to send a numeric message indicating system 
activities to your pager. The system will send the message twice. See “Programming 
Instructions”. 
Use the following table to determine what the numeric message is reporting.
Canceling and 
Preventing 
Accidental 
AlarmsOne of the biggest concerns you might have regarding your security system, is...

Simon Security System10
To cancel an accidental alarm before the programmed dialer delay time expires, enter 
your access code.
Guidelines for Preventing Accidental Alarms
The following guidelines will go a long way toward preventing accidental alarms.
 Close doors and windows before you leave your house.
 Gather your belongings, so you can exit immediately after arming the system.
 Always enter and exit within the programmed delay times.
 Make sure you leave through a door that has a delay time set...

Simon Security System11
calling in a report to the central monitoring station or a pager, due to an action made by 
you or someone at the security system site.
How to Use 
Your 
Touchpads
Touchpads are used to control the security system from any location within or near your 
home.
Remote Handheld Touchpad
Interfacing with the system using a Remote Handheld Touchpad is similar to using the 
panel. 
System Status
Press System Status once to hear information about your system from the panel. See 
“Status...

Simon Security System12
Note  
For any keypress on the 
Keychain Touchpad, hold 
the button until the indicator 
light blinks.LOCK   Press once to arm doors and windows.
LOCK   Press twice to arm doors, windows, and Motion Sensors.
LOCK   Press 3 times to arm doors, windows, Motion Sensors, and to acti-
vate the Latchkey option.
LOCK and UNLOCK   
Press both buttons simultaneously for 3 seconds to send a panic (intru-
sion, silent, or non-medical emergency) alarm to the central monitoring 
station. Check...

Simon Security System13
1. System must be disarmed. Open the Panel Cover by pressing the plastic latch on 
the top of the panel. When you open the cover you will immediately be prompted 
by the panel voice to use the numbered keys to enter your ID. 
Note  
The Master access code is 
1-2-3-4 when the panel is 
shipped. You should change 
your Master Access Code 
after your system is installed 
(see “Access Code”). 2.Enter the Master Access Code.
3. The system voice will prompt you to begin with the START...

Simon Security System14 Note  
Codes are always needed to 
disarm the system. Depend-
ing on the panel configura-
tion, codes may be needed 
to arm the system. Check 
with the installer for your 
system configuration.
Your system may be set up so that the master code or an access code is required when 
arming. If so, the panel will prompt you to enter a code when you attempt to arm the 
system.
Note  
Because different codes can be entered using the same button presses you have to use 
caution when...

Simon Security System15
Unit Number
Refers to a specific light within a house code.


How to set time for light control:
1.Open the cover of the panel.
2. The panel voice prompts you to Use numbered keys to enter ID. Enter your mas-
ter access code using the numbered keys.
3. The panel voice prompts you to Please select from START MENU. Press the Add 
button on the START MENU.
4. The panel voice prompts you to Select from MAIN MENU. Press the Light Con-
trol button on the MAIN MENU.
5. The panel voice...