ADT Security Services OC835ADT Wireless Outdoor HD Camera Installation Guide

							Chapter 3 
ADT Pulse Enrollment  
This section provides examples of  two  different  methods for  enrolling  the 
O C835- ADT Outdoor  HD Camera in to the  ADT Pulse network. (1)  The first method 
uses  a wired connection to enroll the HD Camera to a  Pulse Gateway or TS Base 
panel via the Pulse Portal or TS Installer App . (2) The second metho d uses  WPS to 
wirelessly enroll the HD Camera to a Gateway or TS Base panel via the ADT Pulse 
Portal or TS Installer App . The WPS method is described beginning  on page 15 . 
Using a Wired Connection to Enroll the Camera  
1. Set up the camera, as described in the previous chapter.  
2. Launch an Internet browser and log in to the Pulse portal or TS installer app.  
3. Enter the Manage Devices  screen using one of these methods:  
•  For the Pulse portal, select the System tab and click  Manage Devices. 
•   For the TS installer app, click the  Pulse Devices link.  
The Manage Devices  screen displays. 
4. In the  Manage Devices  screen, click Cameras . 
5.  Click the  Add button at the bottom of the screen.   
 
3 
OC835- ADT Outdoor  HD Camera Installation Guide  11 
  
						

							Chapter 3 ADT Pulse Enrollment 
 
6. Locate the camera’s MAC ID on the label on the rear of the camera.   
 
7. On the  Add Camera screen, enter the camera’s  MAC ID. Do not click Continue 
at this time.  
 
8. Ensure that  the camera  is connected  to the device port  of the Gateway  using 
the  Micro USB to RJ -45 Adapter Cable  / Ethernet cable and connected to the 
supplied 12V DC power adapter .  
9.  After the Power and Network LEDs turn on solid green, click  Continue. 
12   OC835- ADT Outdoor  HD Camera Installation Guide  
  
						

							Chapter 3 ADT Pulse Enrollment 
 
10. Wait for the camera to add. It could take a few minutes, especially if an 
upgrade is required.  
 
11. Assign the camera a unique name (usually based on the location of the 
camera) in the  Name field, and then click the  Save button at the upper right of 
the screen.  
 
OC835-ADT  Outdoor  Day/Night  HD Camera Installation Guide 13  
  
						

							Chapter 3 ADT Pulse Enrollment 
 
12. The Cameras  screen appears, now displaying the added camera.  
 
13. At the top left of the screen, click  Go Back. 
14. You are returned to the Manage Devices  screen. The total number of installed 
cameras has increased by one. Click  Close. 
15.  Click Close  again to confirm.   
16. Disconnect the  camera from the Gateway and remove from power.   
17. Install the camera in  its final location.  For  Wall Mounting , refer to Chapter 4.  
14  OC835- ADT Outdoor  HD Camera Installation Guide  
  
						

							Chapter 3 ADT Pulse Enrollment 
 
Using a Wireless Connection Enroll the Camera 
1. Set up the camera, as described in the previous chapter.  
2. Launch an Internet browser and log in to the Pulse portal or TS installer app.  
3. Enter the Manage Devices  screen using one of these methods:  
•  For the Pulse  portal, select the  System tab and click Manage Devices . 
•   For the TS installer app, click the  Pulse Devices link. 
The Manage Devices screen displays.  
4. In the  Manage Devices  screen, click Cameras . 
5.  Click the  Add Using WPS  button, located at the bottom of the  screen. 
 
6.  Locate the camera’s  PIN number on the lab el on the rear of the camera.  
 
OC835-ADT  Outdoor  Day/Night  HD Camera Installation Guide 15  
  
						

							Chapter 3 ADT Pulse Enrollment 
 
7. Enter th e PIN number  in the WPS PIN  field. 
 
8.  Ensure that the  camera is powered on, and then click the  Continue button to 
i nitiate the WPS  process. 
The following screen appears . 
 
9. Press and hold the WPS/RESET button on the 
camera for 5 seconds t o establish a wireless 
connection . 
The Network/WPS LED flashes amber as the TS 
Base  attempts to connect to the  camera . The 
wireless connection is successful when the 
Network/WPS L ED turns solid green.  
Note:  You must complete the WPS connection 
within 2 minutes or  else the process will time out. 
The time remaining is displayed in the up per left 
portion of the screen.  
16  OC835- ADT Outdoor  HD Camera Installation Guide  
  
						

							Chapter 3 ADT Pulse Enrollment 
 
10.  When the  Camera Details  screen appears, showing that the camera h as been 
enrolled, assign the  OC835-ADT a unique  name (usually based on the location 
of the camera) in the  Name field, and then click  Save. 
 
The Pulse enrollment is complete.  The newly-added device appears  in the 
Cameras  list. 
 
11. At the top left of the screen, click  Go Back. 
12. Disconnect the  camera from power.  
13. Install the c amera in its final location.  
For Wall Mounting , refer to Chapter 4.  
 
OC83 5-ADT  Outdoor  Day/Night  HD Camera Installation Guide 17  
  
						

							Chapter 3 ADT Pulse Enrollment 
 
If the Camera Continually Goes Offline 
If after enrolling it the camera, it continually goes offline (Power LED blinks 
continually), the camera will automatically attempt to recover the wireless 
connection. If the camera cannot recover on its own, take the following measures 
to re -establish the Wi- Fi connection.  
1. Power cycle the camera.  
2. If the previous measure fails, move the Pulse Gateway closer to the camera, if 
possible.  
3. If the previous measure fails, press the camera’s reset button for 15 seconds, 
and then re -enroll the camera into Pulse.  
4. If the previ ous measure fails, install a Wi -Fi Range Extender model 
WN3000RPH -2ADPAS.  
 
18  OC835- ADT Outdoor  HD Camera Installation Guide  
  
						

							Chapter 4 
Wall Mounting  
This section  provides details for  final mounting of  the OC83 5-ADT  Outdoor  
Day/Night HD Camera.  
 
Note: Ensure that the camera is configured and enrolled in ADT Pulse 
before permanently mounting it.  
 
1. Lo cate  a n  u nu sed, no n-sw itc habl e, i n doo r out le t to  p lu g  t h e A C/DC  P ow er 
Ada pte r t o plug into.  This outlet should be located as close as possible to the 
location where the camera will be permanently mounted.  
 
CAUTION: Do not plug in the power adapter until all the 
connections are completed and the camera is fully mounted.  
 
2. Run  t h e supplied  power cab le  f r o m  t h e po wer out le t to  t h e outdoor  loc atio n  
w he re
 th e ca mera  w ill b e m ou nte d.  
3.  At the location where the camera will be mounted, unscrew  the camera stand 
and remove it from the camera . 
4.  Hold the  stand at  the location  where you would like to  mount the camera  and 
mark the location of the two mounting holes.  
5. Drill two holes on the mounting surface  at the marked locations. 
6. If using the anchors, insert them into the mounting holes.  
7. Align the two mounting holes  on the camera stand with the two  holes and 
mount the  stand to the surface using  the two  supplied screws.  
 
Figure  5: Installing the  Camera Stand  
4 
OC835- ADT Outdoor  HD Camera Installation Guide  19 
  
						

							Chapter 4 Wall Mounting 
 
8. Screw/attach the camera onto the camera stand.  
 
Figure  6: Attaching the Camera  
9. Connect the power cable  into the back of the camera , and then insert the 
grommet  between the camera and the power input cover,  as shown in the 
following figures.  
   
Figure  7: Connecting  the Power Cable  
 
CAUTION: Ensure that the grommet is  positioned properly to 
prevent water from entering the camera.  
10. Rotate the power input cover  clockwise to tighten it, providing a watertight 
seal for the power c able. 
 
Figure  8: Securing the Power Cable  
20  OC835- ADT Outdoor  HD Camera Installation Guide