ADT Security Services OC835ADT Wireless Outdoor HD Camera Installation Guide

							 
 
 
 
 
 
 
 
 
 
ADT Pulse® Interactive Solutions 
O C835- ADT 
Wireless  Outdoor HD Camera  
Quick  Installation Guide  
 
    
						

							 
 
Table of Contents 
CHAPTER 1 INTRODUCTION ............................................................................  3 
Overview  ...............................................................................................................  3 
Physical Details  ...................................................................................................  5 
Package Contents  ...............................................................................................  8 
CHAPTER 2 BASIC SETU P .................................................................................  9 
Installation  ............................................................................................................  9 
CHAPTER 3 ADT PULSE  ENROLLMENT .......................................................  11 
Using a Wired Connection to Enroll the Camera  .......................................  11 
Using a Wireless Connection Enroll the Camera  .......................................  15 
CHAPTER 4 WALL MOUNT ING ......................................................................  19 
APPENDIX A SPECIFICA TIONS ......................................................................  23 
OC835 -ADT Outdoor Day/Night HD Camera  ............................................  23 
Regulatory Approvals  ......................................................................................  24 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Property of ADT, LLC. Information accurate as of published date and is provided “as is” 
without warranty of any kind.  
©2015 ADT LLC dba ADT Security Services. All rights reserved. ADT, the ADT logo, 800 
ADT.ASAP and the product/service names listed in this document are marks and/or 
registered marks. Unauthorized use is strictly prohibited.  
OC835- ADT-QIG-01 (0 9/15)  
2  OC835- ADT Outdoor  HD Camera Installation Guide  
  
						

							Chapter 1 
Introduction  
This section provides information about the OC835 -ADT Outdoor Day/Night  HD 
Camera's features, components and capabilities.  
Overview 
The OC835 -ADT is a  true  outdoor  day/night wireless camera with  HD resolution, 
802.11n Wi- Fi connectivity and Wi- Fi Protected Setup (WPS) support. This 
camera is intended for use with ADT Puls e
®. 
Features  
•  Standalone Design.   The  camera  is a standalone syste m with built-in CPU 
and video encoder. It requires only a power source and a connection to  the 
ADT Pulse  Gateway or ADT Total Security (TS) Base panel . 
•   Dual Video Support.  The O C835-ADT support s H.264 and MJEPG video 
compression.  
•   Day/Night Switch:   With the day/night switching feature, you  can view and 
record images even  at night.  
•   IR LED Support. The infrared LED can provide illumination  for up to 6 meters, 
providing superior  video quality under low -light conditions such as on cloudy 
days, or in th e early morning or evening.  
•   PIR (Passive Infrared Sensor) Support. The embedded PIR Sensor senses 
infrared light radiating from hum an bodies in its field of view. 
•   Built -in Heater.   The built -in  heater ensures that  the camera will continue to 
operate even  in extreme ly cold outdoor climate s. The heater turn s on when 
the temperature  falls below  42°F (6°C) . 
1 
O C835- ADT Outdoor  HD Camera Installation Guide  3 
  
						

							Chapter 1 Introduction 
 
Wireless Features  
•  Supports 802.11n Wireless Standard.  The 802.11n standard provides 
backward compatibility w ith the 802.11b and g standards . 
•   Supports WPS.  Wi -Fi Protected Setup  (WPS) can simplify the process of 
connecting  the Wireless HD Camera  to the wireless network by using  the push 
button configuration . 
•   Wired and Wireless Network. The O C835-ADT can be connected to the 
Pulse  network wirelessly . It can also be hardwired to the network . 
4   OC835- ADT Outdoor  HD Camera Installation Guide  
  
						

							Chapter 1 Introduction 
 
Physical Details 
 
Front 
 
Figure  1: Front Panel  
Light Sensor This is a hardware sensor to detect lux. 
Lens The lens cannot be adjusted. Please ensure that the lens 
cover remains clean.   
PIR Sensor This is a Passive Infrared sensor to detect motion. 
 
Light Sensor 
Lens 
PIR Sensor 
OC835-ADT  Outdoor  Day/Night  HD Camera Installation Guide 5  
  
						

							Chapter 1 Introduction 
 
Rear 
 
Figure  2: Rear Panel  
DC Power Input Connect the supplied 12V power adapter here. Do not 
use other power adapters; doing so may damage the 
camera. 
Power LED 
(Green, Amber)  
On (Green).  Power on. 
Off.  No power.  
Blinking (Green).   The Power LED blinks during start up 
for approximately 1 minute.   
Blinking (Amber).   The firmware is being upgraded.  
On (Amber).   The firmware upgrade has failed.  
Network/Wireless 
LED 
(Green, Amber) 
On (Green).  Network connection is available (wired or 
wireless). 
Off.  Wired/wireless network is not connected or 
camera is not sending/receiving data.  
Blinking (Green).   Data is being transmitted or received 
via the wired/wireless connection.  
On (Amber).   If the LED is on for 5 seconds and then 
turns off, t he WPS function has failed.  
Blinking (Amber).   The WPS connection is active.  
Network Port 
WPS/Reset Button 
DC Power Input 
Power LED 
Network/Wireless LED 
6  OC835- ADT Outdoor  HD Camera Installation Guide  
  
						

							Chapter 1 Introduction 
 
WPS/Reset Button  This button serves two functions on the camera. 
•  WPS Pin Code Mode.   When pressed and held for 
5 seconds during the Pulse enrollment process, the 
camera creates  an encryption-secured wireless 
connection.  
•   Reset.  When pressed and held over 15 seconds, 
the camera reboots and the settings are restored to 
default values.  
Network Port Use a Micro USB to RJ-45 Adapter Cable (not included) 
and a standard Ethernet cable  (not included) to connect 
the camera to the Pulse Gateway or TS Base panel.  
Note: 
•   Plugging in the  Micro USB to RJ -45 Adapter  Cable 
will disable the wireless interface. Only one 
interface can be active at any time.  
•   The Micro USB to RJ -45 Adapter  Cable should only 
be connected or disconnected when the camera is 
powered OFF. Attaching or detaching the  Micro 
USB to RJ -45 Adapter  Cable while the camera is 
powered on does NOT switch the interface 
between wired and wireless.  
 
OC83 5-ADT  Outdoor  Day/Night  HD Camera Installation Guide 7  
  
						

							Chapter 1 Introduction 
 
Package Contents 
The following items are  included in the package . 
 
Figure  3: What’s in the Box 
8  OC835- ADT Outdoor  HD Camera Installation Guide  
  
						

							Chapter 2 
Basic Setup  
This section  provides information on how to assemble  and configure 
the  OC835- ADT Outdoor  HD Camera.  
Installation   
1. Assemble the Camera  
Attach the Camera Stand to the  camera. 
2.  Make the Connection  
Using a Wired Connection  
If you are using a wired connection to the OC835- ADT, connect a Micro USB 
to RJ -45 Adapter  Cable (not included) to the USB port of t he camera. Then use 
a standard Ethernet cable (not included) to connect to the Pulse Gateway or 
Total Security (TS) Base panel.  
 
Figure  4: Wire d Network Connection  
Using a Wireless Connection  
The wireless (WPS) connection between the camera and the Pulse Gateway or 
Total Security (TS) Base panel is performed during the Pulse enrollment. This 
process is detailed starting on page  15. 
 
Note: The Wireless and LAN interfaces cannot be used 
simultaneously. Making a wired LAN connection disables the 
wireless interface. 
2 
O C835- ADT Outdoor  HD Camera Installation Guide  9 
  
						

							Chapter 2 Basic Setup 
 
3.  Power Up  
Connect the supplied 12V power adapter to the  camera and power up. Use 
only the power adapter provided. Using a  different one may cause hardware 
damage.  
 
CAUTION:  Use only the power adapter provided. Using a different 
one can result in  hardware damage.  
 
The Power LED turns on briefly, and then starts blinking. (The Power LED will 
continue to blink during startup,  which takes about one minute. After startup is 
completed, the Power LED should remain ON.)  
4. Check the LEDs  
•  Power LED. At power up, t he Power LED turns on briefly, and then start s 
blinking, which take s about one minute. After startup ha s completed, the 
Power LED remain s on . 
•   Network/WPS LED.  At power up, the Network/WPS LED  is off .  
(The Network/WPS LED will flash amber when  the camera attempts to 
connect wirelessly to  the Pulse Gateway / TS Base.  The Network/WPS 
LED will turn solid green w hen the wireless connection is successful.)  
5. Enroll the Camera in ADT Pulse 
This process is described in the next chapter,  ADT Pulse Enrollment. 
6.  Mount the Camera  
Place the camera in a location near a power source. For mounting on a wall 
using the mounting plate , see Chapter 4 Wall Mounting  on page 19. 
 
10   OC835- ADT Outdoor  HD Camera Installation Guide