ADT Security Services Concord Express User Manual
Have a look at the manual ADT Security Services Concord Express User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 68 ADT Security Services manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
21 APPENDIX B: P LANNING FOR EMERGENCIES Develop plans for a variet y of emergency situations. Periodically discuss and rehearse emergency plans that include the following: • Understand how to use your securit y system. • Know the normal state of doors and windows; open, closed, or locked. • Use a different escape route if closed doors feel hot to the touch. • Emphasize that everyone should escape as quickly as possible. Do not stop to gather any belongings. • Crawl and hold your breath as much as possible to help reduce smoke inhalation during your escape. • Meet at a designated outdoor location. • Emphasize that no one should return to the premises if there is a fire. • Notif y fire department from a neighbor’s phone. WARNING! If you arrive at the premises and hear sirens, do not attempt to enter the building. Call for emergenc y assistance from a neighbor’s phone. FLOOR PLAN EXAMPLE The figure on this page is an example of a multilevel floor plan. Use it as a guide and draw your floor plan on the next page. YOUR FLOOR PLAN Use the following guidelines when drawing your floor plan: ¨ Show all building levels. ¨ Show exits from each room (two exits per room are recommended). ¨ Show the location of all securit y system components. ¨ Show the locations of any fire extinguishers. Alarm System Limitations Not even the most advanced alarm system can guarantee protec- tion against burglary, fire, or environmental emergencies. All alarm systems are subject to possible compromise or failure-to-warn, for a variet y of reasons including: • If sirens are not placed within range of persons sleeping, in remote areas of the premises, or if they are placed behind doors or other obstacles. • If intruders gain access through unprotected entry points or areas where sensors are bypassed. • If intruders have the technical means of bypassing, jamming, or disconnecting any or all parts of the system. • If power to sensors is disconnected or inadequate. • If freeze, flood, or any environmental sensors are not located in areas where the specific condition can be detected. • If smoke does not reach a smoke sensor. For example, smoke sensors cannot detect smoke in chimneys, walls, roofs, or smoke blocked by a closed door. Sensors may not detect smoke on building levels different from their installed location. Sensors may not warn in time when fires are caused by smoking in bed, explosions, improper storage of flammables, overloaded electri- cal circuits, or other hazardous conditions.• If telephone lines are out of service. Telephone lines are also vul- nerable to compromise by any of several means. Inadequate maintenance is the most common cause of alarm fail- ure. Therefore, test your system once each week to verif y sensors, sirens, and phone communications are all working correctly. Note:Although having an alarm system can make you eligible for reduced insurance premiums, the system is no substitute for insurance. Warning:Security systems and devices cannot compensate you for life or property losses. Livin g RoomD ining Room Basem ent x H HallBedroomBedroom Livin g Room Recreation Room Basem ent HallBedroom Bedroom Livin g Room D ining Room Hall Bedroom Bedroom Bedroom KitchenA sm oke detector should b e lo cated o n each level. Sm oke detectors s h o u ld b e lo c a t e d b e - tw een the sleeping area and the rest o f th e fa m ily liv in g u n it. H X Livin g RoomBedroom Bedroom BedroomD ining RoomKitchen TV RoomIn fam ily living units w ith m o re than o ne sleeping area, lo c a te a s m o k e d e te c to r at each area. H N O TE: C eiling-m o unted sm o ke detecto rs sho uld b e lo cated in the center o f the room or hall, or not less than 4 inches from the w all. W hen the detector is m o unted o n the w all, the to p o f the detecto r sho uld be 4 to 12 inches fr o m t h e c e ilin g . N O TE: D o no t install sm o ke detecto rs w here no rm al am bient tem peratures are above 100°F or below 40°F. A lso, do not locate detectors in front of A C / H e a t re g is te rs o r o th e r lo c a tio n s w h e re n o rm a l a ir c irc u la tio n w ill keep sm o ke fro m entering the detecto r. N O TE: A d d itio n al in fo rm atio n o n ho u seho ld fire w arn in g is availab le at n o m in al c o s t fr o m : T h e N a tio n a l F ir e P r o te c tio n A s s o c ia tio n , B a tte r y m a r c h P a r k , Q uincy, M A 02269. Request Standard N o. N FPA 74.Required sm oke detector Heat detector Indicates sm o ke detecto r is optional if door is not provided betw een b asem en t an d recreatio n ro o m s.
22 If Your System Needs Service If you have any questions about your securit y system or if it ever needs servicing, please contact your securit y dealer.Company Name _____________________________ Address ____________________________________ Cit y _______________ State _____ Zip __________ Phone Number (_____) _______________________ Contact Name _______________________________ Floor Plan of Your Home or Business
23 APPENDIX C: P ROGRAMMING YOUR SYSTEM You can program the following items on your system: • System time and date • User codes • Downloading feature • Silent Arming feature • Brightness of touchpads • Chime feature TWO METHODS TO PROGRAM YOUR SYSTEM There are 2 methods for programming your system: • Programming menus—Offers visual text cues from your touchpad • Programming shortcuts—Allows you to t ype in a sequence of numbers for a specific programming task. Either method requires a valid System Master code. You cannot program the system using a regular user code. Using Programming Menus The programming menus are arranged much like a computer soft- ware program: menus containing multiple options. To navigate through the menus: Examples of Programming Using Menus Here are two examples of programming using system menus. The examples describe each step involved in programming a user code and in erasing a user code from a fixed English touchpad. To change or assign a user access code: 1. Enter the programming menus by pressing 9 + System Master Code. 2. Press B until the touchpad displays “USER CODES,” then press ƒ. 3. Press B until the touchpad displays the t ype of code you wish to change (Regular User codes or System Master code), then press ƒ. For example, if you want to change a Regular User code, press ƒ when the touchpad displays “REG CODES.” 4. Press B until the touchpad displays the user code you wish to change, then press ƒ. For example, if you want to change Regular User code 2, press ƒ when the touchpad displays “REG CODE 02.” 5. Enter the new code and press ƒ. 6. Press B. “DIREC T BYPASSING” (or “BYPASS”) appears: •Press 1 + ƒ to turn the option off for this user code. •Press 2 + ƒ to turn the option on for this user code. 7. Press B. “SYSTEM TESTS” (or “TESTS”) appears: •Press 1 + ƒ to turn the option off for this user code. •Press 2 + ƒ to turn the option on for this user code. 8. Press ‚ + B to move to the next user code, or ‚ + 4 + ƒ to exit the programming menus. Note:The system will not accept the same code for two different users. To erase a user code: 1. Enter the programming menus by pressing 9 + System Master Code. 2. Press B until the touchpad displays “USER CODES,” then press ƒ. 3. The touchpad displays “REG CODES.” Press ƒ. (You cannot delete the System Master code.) 4. Press B until the touchpad displays the user code you wish to erase, then press ƒ. For example, if you want to change User code 4, press ƒ when the touchpad displays “REG CODE 04,” or “USER 04.” 5. Enter the System Master code you used in Step 1 and press ƒ. The deleted code appears as “REG 01 ––––,” or “USER 01 — ] ] ] ],” for example. 6. Press ‚ + B to move to the next user code, or ‚ + 4 + ƒ to exit the programming menus. Stay Status Featurespress bothLights SystemAway Pager Off No Delay press both press both Test System Weekly Silent 7 08 45 6 3 BypassMenu C 9 P r e s s to m o v e fo rw a rd th ro u g h th e m e n u D*# P r e s s to d e s e le c t an option or to cancel an entry P r e s s to s e le c t an option or to accep t an en try P r e s s to m o ve b ackw ard th ro u g h th e m e n u B A A B ƒ ‚ P r e s s to tu r n a feature o ff1 P r e s s to tu r n a feature o n2 12 Press num bered keys w h en valu es o r co d e cho ices are re q u e s te d
24
ƒ
B
ƒ‚
ƒ‚
ƒ‚
ƒ‚
B
BB
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
At a touchpad, press
9
Enter the System Master code.System displays briefly:
Press to
return to the start of the
Programming Menu.
B
Press to move forward in the menu.
B
Press to move backward in the menu.
B
A
A
ƒ‚
Press to back out of the menu.
Press to enter the menu.
‚
ƒ
Press to turn a feature off.
1
Press to turn a feature on.
2
System displays:Then, system displays:
Silent ArmingWhen feature is on:
Status beeps while
arming will be silent.
Chime On CloseWhen feature is on and Chime
is turned on ( + ):
2 beeps sound when a protected
door or window is opened.
1 beep sounds when the door
or window is closed again.
DownloadingWhen feature is on:
Allows dealer to
make changes to
the system
from off-site.
System TestsA user attribute that,
when
on, allows the
user to enter test mode
by pressing:
+
code
+
(Phone Test)
+
code
+
(Sensor Test)
Direct BypassingA user attribute that,
when
on, allows the
user to bypass sensors
directly by pressing:
+
code
+
sensor number
2
Press + for
next User Code.
Continue to press
for User Codes.
B
ƒ
ƒ
ƒ‚
‚B
Press + for
next User Code.
‚B
Press + for
next User Code.
‚B
ƒ
+ for Off1ƒ + for On2ƒ
+ for Off1ƒ + for On2ƒ
+ for Off1ƒ + for On2ƒ
+ for Off1ƒ + for On2ƒ
+ for Off1ƒ + for On2ƒ
+ for Off1ƒ + for On2ƒ
B
B
B
ƒ‚
+ for Low1ƒ + for Medium2ƒ + for High
ƒ
+ for Off1ƒ + for On2ƒ
+ for Off1ƒ + for On2ƒ
+ for Off1ƒ + for On2ƒ
+ for Off0ƒ
Chim e
B
B
B
B
B
Press to
return to Reg Code 00.
B
8642G71A.DSF
(Chime On Close) (Touchpad Brightness) (Silent Arming) (Downloading)
3
(Regular User Codes) (System Master Code)
(Direct Bypassing) (System Tests)
En te r co d e
ƒ8
71
System is O K
3 8
Programming Menus:
25 Using Programming Shortcuts A programming shortcut is a number that gets you to a particular spot in the programming menus. A series of shortcut numbers takes you directly to the feature or code you want to change.The table below lists: 1. How to enter the programming menus. 2. User programming tasks. 3. The sequence of keypresses to take you to the task. 4. Specific information to enter for the task. 5. How to accept an entry. 6. How to exit the programming menus. 1. Enter programming menus:2. Choose programming task. 3. Enter ‚ + ‚, then key sequence.4. Enter value or choice.5. Secure choice.6. Exit programming menus. 9 + Master CodeSet system time 0 0 Time in 24-hour format (Enter 4 digit s)ƒ‚ + 4 + ƒ Set system date 0 1 Enter 6-digit date in mm/dd/yy format Change User code 00 1 0 0 0 04-digit code Direct Bypassing for User 00 1 0 0 0 1 1 (Off) or 2 (On) System Tests for User 00 1 0 0 0 2 Change User code 01 1 0 0 1 04-digit code Direct Bypassing for User 01 1 0 0 1 1 1 (Off) or 2 (On) System Tests for User 01 1 0 0 1 2 Change User code 02 1 0 0 2 04-digit code Direct Bypassing for User 02 1 0 0 2 1 1 (Off) or 2 (On) System Tests for User 02 1 0 0 2 2 Change User code 03 1 0 0 3 04-digit code Direct Bypassing for User 03 1 0 0 3 1 1 (Off) or 2 (On) System Tests for User 03 1 0 0 3 2 Change User code 04 1 0 0 4 04-digit code Direct Bypassing for User 04 1 0 0 4 1 1 (Off) or 2 (On) System Tests for User 04 1 0 0 4 2 Change User code 05 1 0 0 5 04-digit code Direct Bypassing for User 05 1 0 0 5 1 1 (Off) or 2 (On) System Tests for User 05 1 0 0 5 2 Change User code 06 1 0 0 6 04-digit code Direct Bypassing for User 06 1 0 0 6 1 1 (Off) or 2 (On) System Tests for User 06 1 0 0 6 2 Change User code 07 1 0 0 7 04-digit code Direct Bypassing for User 07 1 0 0 7 1 1 (Off) or 2 (On) System Tests for User 07 1 0 0 7 2
26 9 + Master CodeChange User code 08 1 0 0 8 04-digit codeƒ‚ + 4 + ƒ Direct Bypassing for User 08 1 0 0 8 1 1 (Off) or 2 (On) System Tests for User 08 1 0 0 8 2 Change User code 09 1 0 0 9 04-digit code Direct Bypassing for User 09 1 0 0 9 1 1 (Off) or 2 (On) System Tests for User 09 1 0 0 9 2 Change User code 10 1 0 1 0 04-digit code Direct Bypassing for User 10 1 0 1 0 1 1 (Off) or 2 (On) System Tests for User 10 1 0 1 0 2 Change User code 11 1 0 1 1 04-digit code Direct Bypassing for User 11 1 0 1 1 1 1 (Off) or 2 (On) System Tests for User 11 1 0 1 1 2 Change User code 12 1 0 1 2 0 4-digit code Direct Bypassing for User 12 1 0 1 2 1 1 (Off) or 2 (On) System Tests for User 12 1 0 1 2 2 Change User code 13 1 0 1 3 04-digit code Direct Bypassing for User 13 1 0 1 3 1 1 (Off) or 2 (On) System Tests for User 13 1 0 1 3 2 Change User code 14 1 0 1 4 04-digit code Direct Bypassing for User 14 1 0 1 4 1 1 (Off) or 2 (On) System Tests for User 14 1 0 1 4 2 Change User code 15 1 0 1 5 04-digit code Direct Bypassing for User 15 1 0 1 5 1 1 (Off) or 2 (On) System Tests for User 15 1 0 1 5 2 Change System Master Code 1 1 04-digit code Downloading 2 0 1 (Off) or 2 (On) Silent Arming 2 1 1 (Off) or 2 (On) Touchpad Brightness 2 2 0 for Off 1 for Low 2 for Medium 3 for High Chime on Close 2 5 1 (Off) or 2 (On) Factory Code 3 0 System Number 3 1 System Level 3 2 1. Enter programming menus:2. Choose programming task. 3. Enter ‚ + ‚, then key sequence.4. Enter value or choice.5. Secure choice.6. Exit programming menus.
30 FCC Notices This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particu- lar installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Install a quality radio or television outdoor antenna if the indoor antenna is not adequate. • Reorient or relocate the panel. • Move the panel away from the affected equipment. • Move the panel away from any wire runs to the affected equipment. • Connect the affected equipment and the panel to separate outlets, on different branch circuits. • Consult the dealer or an experienced radio/TV technician for help. • Send for the FCC booklet How to Identify and Resolve Radio-TV Interfer- ence Problems, available from the U.S. Government Printing Office, Washington, D.C. 20402. Stock Number: 004-000-00345-4. Changes or modifications not expressly approved by Interactive Technolo- gies, Inc. can void the user’s authority to operate the equipment. This equipment complies with part 68 of the FCC rules. On the FCC label affixed to this equipment is the FCC Registration Number and Ringer Equiv- alence Number (REN) for this equipment. If requested, provide this infor- mation to your telephone company. The REN is used to calculate the maximum number of devices your tele- phone line will support with ringing service. In most areas the sum of all device RENs should not exceed 5.0. Contact your local telephone company to determine the maximum REN for your calling area. If your telephone equipment causes harm to the telephone network, your telephone company may temporarily disconnect your service. If possible, you will be notified in advance. When advance notice is not practical, you will be notified as soon as possible. You will also be advised of your right to file a complaint with the FCC. Your telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the proper operation of your equipment. You will be given advanced notice in order to maintain uninter- rupted service. The telephone company may ask you to disconnect this equipment from the network until the problem has been corrected or until you are sure that the equipment is not malfunctioning. This equipment may not be used on coin service provided by the telephone company. Connec- tion to party lines is subject to state tariffs. Declaration of Conformity (DoC) Interactive Technologies, Inc. declares that the ITI model no. 60-792-95R is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Industry Canada Warnings Notice: The Industry Canada Label identifies certified equipment. This certification means that the equipment meets telecommunications network protective, operational, and safety requirements as prescribed in the appropriate Termi- nal Equipment Technical Requirement document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of con- nection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunica- tions company cause to request the user to disconnect the equipment.Users should ensure for their own protection that the electrical ground con- nections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electri- cian, as appropriate. Notice: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Number of all the devices does not exceed 5. AVIS D’INDUSTRIE CANADA AVIS: L’étiquette d’Industrie Canada identifie le matériel homologué. Cette éti- quette certifie que le matériel est conforme aux normes de protection, d’ exploitation et de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigences techniques relatives au matérial terminal. Le Ministere n’assure toutefois pas que le matériel fonc- tionnera à la satisfaction de l’utilisateur. Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le raccorder aux installations de l’enterprise locale de télécommunication. Le matériel doit également être installé en suivant une méthode acceptée de raccordement. L’abonné ne doit pas oublier qu’il est possible que la confor- mité aux conditions énoncées ci-dessus n’empêche pas le dégradation du service dans certaines situations. Les réparations de matériel homologué doivent être coordonnées par un représentant désigné par le fournisseur. L’entreprise de télécommunications peut demander à l’utilisateur de débrancher un appareil à la suite de répara- tions ou de modifications effectuées par l’utilisateur ou à cause de mauvais fonctionnement. Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de mise à la terre de la source d’énergie électrique, des lignes téléphoniques et des canalisations d’eau métalliques, s’il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions rurales. Avertissment: L’utilisateur ne doit pas tenter de faire ces raccordements lui- meme; il doit avoir recours à un service d’inspection des installations élec- triques, ou à électricien, selon le cas. AVIS: L’indice d’équivalence de la sonnerie (IES) assigné à chaque dispositif termi- nal indique le nombre maximal de terminaux qui peuvent être raccordés à une interface. La terminaison d’une interface téléphonique peut consister en une combinaison de quelques dispositifs, à la seule condition que la somme d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5. Trademarks ITI is a registered trademark of Interactive Technologies, Inc. Concord, SuperBus, SnapCard, and ToolBox are trademarks of Interactive Technolo- gies, Inc. X-10 is a registered trademark of X-10 (USA), Inc. This manual may refer to products that are announced but are not yet avail- able.