ADT Security Services Ademco 10SE User Manual

							–11–
SECURITY CODES (Continued)
Duress Code
(Continued)
To program a Duress code:Enter your Master Code + 8 + 8 + [desired 4-digit duress code].
The keypad will beep once.
Note: The Duress code must differ from the Master Code or any other User’s Code.To change the Duress code:Enter Master Code + 8 + 8 + [new 4-digit duress code].To delete the Duress code:Enter your Master Code + 8 + 8,  and then stop. When the keypad beeps once it signifies
that the code has been deleted.
To Change Your Master
Code1 . Enter your Master code and press the CODE [8] key.
2 . Enter “2”.
3 . Enter your new Master code.
4. Enter your new Master code again. The keypad will beep 3 times, indicating
acceptance.
Quick Arming
Ask your installer if QuickArming is active for yoursystem; if so, check here:
    
If your system supports Quick Arming, the # key can be pressed in place of the
security code when arming the system. The security code is 
always
 required, however,
when disarming the system.
Phone Module
Ask your installer if yoursystem includes a phonemodule; if so, check here: 
   
If your system includes a phone module, your installer will have programmed a 2-digit
phone access code for your system. Be sure to obtain this phone code from your installer.
Complete information regarding the use of this phone access feature is provided in a
separate manual entitled PHONE ACCESS USERS GUIDE, which accompanies the
phone module. 
						

							–12–
ENTRY/EXIT DELAYS
General InformationYour system has preset time delays, known as exit delay and entry delay. When you arm
your system, exit delay gives you time to leave through the entry/exit door without
setting off an alarm.  Entry delay gives you time to disarm the system when you re-enter
through the entry/exit door. The system must be disarmed, however, before the entry
delay period ends, or an alarm will occur. The keypad will beep slowly during the entry de-
lay period, reminding you to disarm the system.
You can also arm the system with no entry delay at all by using either INSTANT or
MAXIMUM arming modes. These modes can provide greater security while you are
sleeping or while you are away for extended periods of time.
See your installer for your delay times and record them here:
Exit Delay:       
 secondsEntry Delay:    
 seconds
Remember, there will be no entry delay
when arming INSTANT or MAXIMUM.
Exit Delay
Alerting SoundWhen arming AWAY (see page 18) or MAXIMUM (see page 19), slow beeps will sound
from the keypad(s) during the exit delay, turning to fast beeps during the final five
seconds of the exit delay time.
Ask your installer if this feature is active for your system, and if so, check here:         
						

							–13–
CHECKING FOR OPEN ZONES
Using the
 
 Q
  READY Key
Before arming your system, all protected doors, windows and other protection zones
must be closed or bypassed (see 
BYPASSING
 PROTECTION
 ZONES
 section), otherwise
the keypad will display a Not Ready message, and if your keypad has a READY indicator
light, it will not be lit. The READY key can be used to display all faulted zones, making it
easier for you to secure any open zone.
To display faulted zones, simply press and release the READY [Q] key (do not enter
code first).
Secure or bypass the zones displayed before arming the system.
A Ready message will be displayed when all protection zones have been either closed
or bypassed and the keypads READY indicator light (if present) will be lit. The system can
then be armed. if desired.
 READY
TO DISPLAY OPEN ZONES, PRESS THE   
 Q 
 KEY.
TYPICAL DISPLAYS
WHEN NOT READY TO ARM
DI S A R M E D  -  
PR ES S
 Q
TO SHOW   FAULTS
ALPHATYPICAL DISPLAYS
INDICATING OPEN PROTECTION ZONE
(AFTER PRESSING READY KEY)
FAULT 06 FRONTUPSTAIRS BEDROOM
ALPHATYPICAL DISPLAYS
INDICATING READY TO ARM
****
 DI S A R M E D
 ****
RE ADY TO ARM
ALPHA
AC
NOT READY
06
AC
NOT READYAC
READY
FIXED-WORD FIXED-WORD FIXED-WORD 
						

							–14–
BYPASSING PROTECTION ZONES
Using the
 
 6 
 BYPASS KeyLIMITATION
The system will notallow fire zones tobe bypassed.
All bypasses are removedwhen an OFF sequence(security code plus OFF)is performed.
This key is used when you want to arm your system with one or more zones intentionally
unprotected. The system must be disarmed first.
1 . Enter your security code and press the BYPASS key.
2 . Enter the zone number(s) for the zone(s) to be bypassed (e.g., 06, 10, 13, etc.).
Single digit zone numbers must be preceded by a zero (e.g. 05, 06)
.
3 . When finished, the keypad will momentarily display a Bypass message for each by-
passed zone number. Wait for these zones to be displayed, to confirm their bypass.
4 . Arm the system as usual.
Bypassed zones are unprotected and will not cause an alarm if violated
while your system is armed.
TO BYPASS ZONES:
• Enter Code.
• Press Bypass Key.
• Enter Zone Nos.
• Wait For Bypassed Zones
   To Be Displayed.
• Arm System As Usual.
TYPICAL MOMENTARY DISPLAYS
OF BYPASSED ZONEBYPASS 06 FRONTUPSTAIRS BEDROOM
ALPHA
ÊÊ06
BYPASSACFIXED-WORD 
						

							–15–
BYPASSING PROTECTION ZONES (Continued)
Quick Bypass
Ask your installer ifQuick Bypass is activefor your system, and ifso, check here:  
   
If your system supports Quick Bypass, it allows you to easily bypass all open (faulted)
zones without having to enter zone numbers individually. This feature is useful if, for
example, you routinely leave certain windows open when arming at night.
To use this feature, enter your security code, press the BYPASS key, then stop. In a few
moments, all open zones will be displayed along with a Bypass message. Wait for all
bypassed zones to be displayed, then arm the system as usual.
TYPICAL DISPLAYS
READY TO ARM WITH ZONES BYPASSED
BYPASSAC
READY
DISARMED BYPASSRE ADY TO ARM
FIXED-WORD ALPHA
THE SYSTEM CAN NOW BE ARMED WITH ZONE(S) BYPASSED 
						

							–16–
ARMING PERIMETER ONLY
WITH ENTRY DELAY ON
Using the
 
 3 
 STAY Key
BEFORE ARMING,close all doors and windows(see 
CHECKING
 FOR
 OPEN
ZONES
 on page 13).
 THE STAY MODE ARMS THE PERIMETER, BUT ALLOWS USE OF THE ENTRY/EXIT DOOR. PERSONS WITHIN THE PREMISES CAN MOVE ABOUT FREELY.
Use this key when  staying inside, but expect someone to use an entry/exit door later.
1 . Enter your security code and press the STAY key.
2 . The keypad beeps three times and displays the armed STAY message. The red
ARMED indicator lights. Note that there is an 
exit 
delay in effect before arming actually
takes place. See the note below.
3 . After arming, an alarm sounds immediately if a protected perimeter window or non-
entry/exit door is then opened, but you may otherwise move freely throughout the
premises.
Anyone entering later can enter through an entry/exit door without causing an alarm, but
they must disarm the system within the 
entry
 delay period to avoid sounding an alarm.
If you wish to open the entry/exit door to let someone in after arming STAY, you can re-
start the 
exit 
delay at any time – simply press the [
Q] key, and then let that person in.
This will avoid having to disarm the system and then re-arm it again.
Note:When you first arm the system in the STAY mode, “You may exit now” will be
displayed on the second line of an Alpha keypad during the programmed exit
delay. 
This delay is in effect in the system even when arming STAY.
  When the
exit delay period ends, the system is fully armed in the STAY mode.
TYPICAL DISPLAYS – “ARMED STAY”
STAY
AC
ARME D  
***
STAY 
***
YOU MAY EXIT  NOW
FIXED-WORD
The message “
you may exit now”
>
ALPHA
disappears when the exit delay expires. 
						

							–17–
ARMING PERIMETER ONLY
WITH ENTRY DELAY OFF
Using the
 7 
 INSTANT Key
BEFORE ARMING,close all doors and windows(see 
CHECKING
 FOR
 OPEN
ZONES
 on page 13)
 THE INSTANT MODE ARMS THE PERIMETER (INCLUDING THE ENTRY/EXIT DOOR), WITH NO ENTRY DELAY. PERSONS WITHIN THE PREMISES CAN MOVE ABOUT FREELY
Use this key when staying inside and do not expect anyone to use an entry/exit door.
1 . Enter your security code and press the INSTANT key.
2 . The keypad beeps three times and displays the armed message. The red ARMED
indicator lights.  Note that there is an 
exit 
delay in effect before arming actually takes
place. See the note below.
3 . After arming, an alarm sounds immediately if any protected perimeter door or window
is opened, but you may otherwise move freely throughout the premises.
An alarm sounds immediately if anyone opens an entry/exit door.
If you wish to open the entry/exit door to let someone in after arming INSTANT, you can
re-start the 
exit 
delay at any time – simply press the [
Q] key, and then let that person
in. This will avoid having to disarm the system and then re-arm it again.
Note:When you first arm the system in the INSTANT mode, “You may exit now” will be
displayed on the second line of an Alpha keypad during the programmed exit
delay. 
This delay is in effect in the system even when arming INSTANT.
  When the
exit delay period ends, the system is fully armed in the INSTANT mode.
TYPICAL DISPLAYS –  “ARMED INSTANT”
STAYINSTANT
AC
ARME D  
*INSTANT
*
YOU MAY EXIT  NOW
FIXED-WORD
>
ALPHA
The message “
you may exit now
 “
disappears when the exit delay expires. 
						

							–18–
ARMING ALL PROTECTION
WITH ENTRY DELAY ON
Using the
 
 2 
 AWAY Key
BEFORE ARMING,close all doors and windows(see 
CHECKING
 FOR
 OPEN
ZONES
 on page 13)
Use this key when no one will be staying inside.
1 . Enter your security code and press the AWAY key.
2 . The keypad beeps twice and displays the armed message. The red ARMED indicator
lights.
3 . You may leave through an entry/exit door during the exit delay period without causing
an alarm.
After the exit delay expires, the system arms and sounds an alarm immediately if a
protected window or non-entry/exit door is opened, or if any movement is detected inside
your premises.
You may re-enter through an entry/exit door, but must disarm the system
within the entry delay period to avoid an alarm.
THE AWAY KEY
ARMS THE ENTIRE SYSTEM
(INTERIOR AND PERIMETER),
BUT ALLOWS USE OF
THE ENTRY/EXIT DOOR.
TYPICAL DISPLAYS
ARMED AWAY
AR M E D
 ***
 AWAY
 ***
YOU MAY EXIT  NOWThe message you may exit now changes to
ALL SECURE when the exit delay expires.
ALPHA
AWAY
AC
FIXED-WORD 
						

							–19–
ARMING ALL PROTECTION
WITH ENTRY DELAY OFF
Using the
 
 4 
 MAXIMUM Key
BEFORE ARMING,close all doors and windows(see 
CHECKING
 FOR
 OPEN
ZONES
 on page 13)
Use this key when the premises will be vacant for extended periods of
time such as vacations, etc., or when retiring for the night and no one will be moving
through protected interior areas.
1 . Enter your security code and press the MAXIMUM (MAX) key.
2. The keypad beeps twice and displays the armed MAXIMUM message. The red
ARMED indicator lights.
3 . You may leave through an entry/exit door during the exit delay period without causing
an alarm.
After the exit delay expires, the system arms and sounds an alarm immediately if any
protected door or window is opened, or if any movement is detected inside your
premises.
An alarm sounds immediately, when someone re-enters.
THE MAXIMUM KEY
ARMS THE ENTIRE SYSTEM
(INCLUDING THE ENTRY/EXIT DOOR
WITH NO ENTRY DELAY).
TYPICAL DISPLAYS
ARMED MAXIMUM
AR M E D
 * MAXIMUM
 *
YOU MAY EXIT  NOWThe message you may exit now changes to
ALL SECURE when the exit delay expires.
ALPHA
AWAY
INSTANTAC
FIXED-WORD 
						

							–20–
DISARMING THE SYSTEM AND SILENCING ALARMS
Using the
 
 1 
 OFF Key
IMPORTANT:
If you return and themain burglary sounder ison, DO NOT ENTER, butCONTACT THE POLICE from anearby safe location.If you return after analarm has occurred andthe main sounder hasshut itself off, the keypadwill beep rapidly upon yourentering, indicating that analarm has occurred duringyour absence.LEAVE IMMEDIATELY, andCONTACT THE POLICE from anearby safe location.
The OFF key is used to disarm the system and to silence alarm and trouble sounds.To Disarm the SystemEnter your security code and press the OFF key.
The Ready message will be displayed, and the keypad will emit a single tone to confirm
that the system is disarmed.To Silence a Burglary AlarmSEE IMPORTANT NOTE AT LEFT!
Enter your security code and press the OFF key to silence the alarm (or warning tones
of a Memory of Alarm).
Note the zone in alarm on the keypad display, and make that zone intact (close door,
window, etc.). Now enter the security code plus OFF sequence again to clear the
keypads Memory of Alarm display. If the display will not clear and does not provide a
Ready message, notify the alarm agency.To Silence a Fire AlarmSimply press the OFF key 
(the security code is not needed to silence FIRE alarms).
To then clear the keypads Memory of Alarm display, enter your security code and press
the OFF key again. See page 29 for additional fire alarm information.
A FIRE alarm is an interrupted/pulsed sound. A BURGLARY alarm is a continuous/steady sound.
TYPICAL FIRE ALARM DISPLAY TYPICAL BURGLARY ALARM DISPLAY
FIR E    05MA STE R BE D RO OM
Ê05ALARM
FIRE
AC
ALARM 05MA STE R BE D RO OM
 05ALARM
AC
ALPHA FIXED-WORDALPHA  FIXED-WORD