Addonics Technologies Diamond 35 Hard Drive dmrsa User Manual

							 
 
 
 
 
 
 
Addonics 
T E C H N O L O G I E S 
 
 
 
 
Diamond Mobile Rack 
 
DMRSAI & DMRII 
DMRSASC & DMRISC 
 
 
 
 
 
 
User’s Guide 
 
 
 
 
 
 
 
 
 
 
 
 
 
Version 1.0           
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
						

							FCC Warning Statement 
This equipment has been tested and found to comply with the limits for a class B 
digital device pursuant to Part 15 of the FCC rules.  These limits are designed to 
provide reasonable protection against harmful interference in a residential 
installation.  This equipment generates, uses and can radiate radio frequency 
energy.  If not installed and used in accordance with the instructions, it may 
cause harmful interference to radio communications.  However, there is no 
guarantee that interference will not occur in a particular installation.  If the 
equipment does cause harmful interference to radio or television reception, which 
can be determined by turning the equipment on and off, the user is encouraged 
to try and correct the interference by one or more of the following suggestions. 
Reorient or relocate the receiving antenna 
Increase the distance between the equipment and the receiver  
Connect the equipment to a different power outlet other than the one where 
receiver is connected 
Consult a certified television or radio technician 
 
 
LIMITED WARRANTY 
Addonics guarantees that every product is free from physical defects in material 
and workmanship during the warranty period specified for each product when used 
within the limits set forth in the Specifications section in the user guide. 
Unauthorized tampering of the product or using it outside the scope of the 
product specifications will result in voiding the warranty. If the product proves 
defective during this warranty period, call Addonics Technical Support to obtain a 
Return Authorization number. BE SURE TO HAVE YOUR PROOF OF 
PURCHASE ON HAND WHEN CALLING. RETURN REQUESTS CANNOT BE 
PROCESSED WITHOUT PROOF OF PURCHASE. When returning a product, 
mark the Return Authorization number clearly on the outside of the package and 
include your original proof of purchase. Customers are responsible for paying the 
shipping and handling of the products to Addonics warranty service location. 
IN NO EVENT SHALL ADDONICS’ LIABILITY EXCEED THE PRICE PAID FOR 
THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR 
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE 
PRODUCT, ITS ACCOMPANYING SOFTWARE, OR ITS DOCUMENTATION. 
Addonics makes no warranty or representation, expressed, implied, or statuary, 
with respect to its products or the contents or use of the user guide and all 
accompanying software, and specifically disclaims its quality, performance, 
merchantability, or fitness for any particular purpose. Addonics reserves the right 
to revise or update its products, software, or documentation without obligation to 
notify any individual or entity. 
 
 
 
 
 
 
 
 
 
 
 
Hardware Installation Guide 
 
Step 1 
Use a Philips screwdriver to 
turn the cover securing 
screw into the “OPEN” 
position. 
 
 
 
 
 
 
 
 
 
Step 2 
Slide the aluminum cover 
towards the back end of the 
Diamond and remove it. 
 
 
 
 
 
 
 
 
 
 
 
 
Step 3 
 
For SATA Drive 
Carefully place the SATA hard drive 
with the label facing up into the 
Diamond enclosure.  Push the hard 
drive towards the back end to secure 
the drive connectors onto the 
Diamond enclosure’s SATA 
connector. 
 
 
 
 
 
 
 
 
        
						

							For IDE Drive 
Note: Set up your IDE hard drive 
as Master device 
 
Connect the 4-Pin Molex cable to 
the power connector on the IDE 
hard drive. Carefully place the IDE 
hard drive with the label facing up 
into the Diamond enclosure.  Push 
the hard drive towards the back end 
to secure the drive connectors onto 
the Diamond enclosure’s IDE 
connector. 
 
 
Step 4 
Turn the Diamond enclosure over with 
the hard drive mounting holes facing 
up. Use the included flat head  
screws to secure the hard drive onto 
the bottom of theenclosure and turn in 
the screw to the “LOCK” position. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Cable Connections 
 
Model: DMRSAI & DMRII 
 
Power: Using the 4-pin floppy connector of the Y-cable, connect it to the floppy-
type power connector on the converter. To provide power for the y-cable, 
connect it to one of your desktops 4-pin molex cable. 
 
Data: Connect the IDE ribbon cable to the 40-pin IDE connector of the SATA to 
IDE converter board and to the IDE channel of your motherboard. 
 
LED cable: No need to connect. By factory default, LED signal would come from 
the hard drive. 
 
Powering On Drive Cradle:  
To power on the drive cradle, slide in the Diamond cartridge and using the key 
(supplied), turn the cradle lock located at the front of the cradle to the LOCK 
position. This will provide power as indicated by the green LED lighting up and 
secure the cartridge. 
 
 
 
Note: This configuration would not support hot-swap. 
 
 
 
 
 
 
 
 
 
Power & Drive Activity LED 
Key Lock Switch 
IDE-SATA Converter 
40-pin IDE ribbon cable        
						

							 
Model: DMRSASC & DMRISC 
 
Power: Using the 4-pin floppy connector of the Y-cable, connect it to the floppy-
type power connector on the converter. To provide power for the y-cable, 
connect it to one of your desktops 4-pin molex cable. 
 
Data: Connect the SCSI cable to the 68-pin SCSI connector of the SATA to SCSI 
converter board and to your SCSI controller. 
 
LED cable: No need to connect. By factory default, LED signal would come from 
the hard drive.  
 
Powering On Drive Cradle: To power on the drive cradle, slide in the Diamond 
cartridge and using the key (supplied), turn the cradle lock located at the front of 
the cradle to the LOCK position. This will provide power as indicated by the 
green LED lighting up and secure the cartridge. 
 
 
 
 
Note: This configuration would not support hot-swap. 
 
 
 
 
 
 
 
 
 
 
 
Technical Support 
 
If you need assistance to get your unit functioning properly, please call Addonics 
Technical Support.  Our technical staff will be happy to assist you, but they will 
need your help to do so.  Calling the technical support staff without all the proper 
information can be both time consuming and frustrating.  Here are some tips to 
help you out: 
 
MODEL NUMBER – Please have this number on hand. 
SYSTEM INFORMATION – Type of computer, peripherals, etc. 
  OPERATING SYSTEM – What version of Windows   
  WHAT’S THE TROUBLE? – Give enough information  
about your problem so that we can recreate and diagnose it. 
 
FREE Software Drivers for all Addonics Technologies 
Products are available 24 hours per day at the  
World Wide Web Site: www.addonics.com. 
 
Contact Information 
Phone:  408-433-3899 
Fax:  408-433-3898 
Email:  http://www.addonics.com/sales/query/ 
Internet:  http://www.addonics.com 
 
TECHNICAL SUPPORT 
Phone:  408-433-3855 
Hours:  8:30 am - 6:00 pm PST 
Email:  http://www.addonics.com/support/query/ 
 
 
 
 
 
 
 
 
 
 
Power & Drive Activity LED 
Key Lock Switch 
IDE-SCSI Converter 
68-pin SCSI ribbon cable