ADDER ePower Switch 1 Guard Manual

 
20 A total of 32 rules can be created and there are 4 different types of rules: 
 
1. Schedule Rule: 
This rule is used to trigger user-specified actions according to a defined time table.  
This rule can be used to:  
- execute once defined actions at specified time and weekday(s). In this case you must only specify the 
start time and the weekday(s), 
- execute repeatedly defined actions during a given time. In this case you must specify the start time, the 
interval on which the rule has to be...

21 
3.3.8.1. Settings / Rules - Schedule Rule 
 
This rule can be used to trigger user-specified actions according to a defined time table. The schedule rule 
is weekday based and the administrator can declare, for each weekday, a start time, an end time and after 
what time the rule should be repeated.  
 
 
 
Activated 
This check box must be checked to activate the Rule and enables to deactivate temporarily a rule while 
keeping all its settings for a later use. 
Rule ID: 
The ePowerSwitch 1G
R2...

 
22 Stop Time 
Defines what time the rule ends. 
- End Time must be greater than or equal to Start Time. 
- If the rule has to be executed only once at the selected weekday, enter the same value for Start 
Time and End Time. 
- If the rule has to be executed 24 hours at the selected weekday, Start Time must be 1 minute 
later than EndTime. 
Applicable weekday 
Defines which day(s) the rule has to be executed. 
 
Type of Action 
 
For the Event defined above, you can choose and configure following...

23 
3.3.8.2. Settings / Rules - Timer Rule 
 
This rule can be used to trigger some actions according to a defined time table. 
For instance, you could create a rule to switch OFF a Power Outlet every Friday at 6 PM and create 
another rule to switch the Power Outlets ON again every Monday at 8 AM. 
 
 
 
Activated 
This check box must be checked to activate the rule. It enables to deactivate temporarily a rule while 
keeping all its settings for a later use. 
Rule ID 
The Power Switch automatically...

 
24  
Set Power Outlet: 
Check this box and in the corresponding drop-down list, choose the power outlet the rule will apply to. In 
the next corresponding drop-down list, choose the action to execute. Each power outlet can be switched 
On/Off and restarted. If you choose restart you will also be able to define a restart delay between 0 and 
65535 seconds. 
- If you choose 0 second, the delay will be the delay defined in the ePowerSwitch power outlets settings. 
- If you choose a delay different from 0,...

25 
3.3.8.3. Settings / Rules - Ping Monitoring Rule 
 
This rule can be used to check if a computer or any IP device is connected to the network. It sends ping 
packets and listens for replies from the specific host. If the host doesnt reply, the ePowerSwitch 1G
R2 can 
automatically switch the powered device off and after a specified delay, switch it again on (for details see 
Ping & Scan Method). 
 
 
 
Activated 
This check box must be checked to activate the Rule and enables to deactivate...

 
26  
Delay before First Request after Action: 
In this field, define the time in seconds before restarting the monitoring after the reboot action. 
The delay can be set between 30 and 65535 seconds.  
Maximum Number of Actions 
In this field, define the maximum number of actions. 
The number can be set between 0 and 255. 
 
 
Type of Actions: 
 
For the Event defined above, you can choose and configure following actions: 
 
Set Power Outlet: 
Check this box and in the corresponding drop-down list,...

27 
3.3.8.4. Settings / Rules - Scan Monitoring Rule 
 
This rule can be used to check if a specific protocol is available on a server (for example HTTP, FTP, 
Telnet, POP...). If the connection is possible, ePowerSwitch 1G
R2 knows that a server program is running 
there. If the connection is not possible, ePowerSwitch 1GR2 can automatically switch the powered device 
off and, after a specified delay, switch it again on (for details see Ping & Scan Method). 
 
 
 
Activated 
This check box must be...

 
28  
Number of unsuccessful Requests before Action: 
In this field, define the number of Port scanning commands to be sent to the IP device before executing 
the actions. 
The number can be set between 1 and 65535 seconds. 
Delay before First Request after Action: 
In this field, define the time in seconds before restarting the monitoring after the reboot action. 
The delay can be set between 30 and 65535 seconds. 
Maximum Number of Actions 
In this field, define the maximum number of actions. 
The...

29 
3.3.9. Settings / Shutdowns 
 
This power switch supports shutdown facilities of 1 server via its Serial RS232 interface. 
 
 
 
- To remove an existing Shutdown association, click on Delete of the corresponding rule.  
- To modify a Shutdown rule, click on Edit of the corresponding rule. 
 
This page is used to create, modify and delete a Shutdown Association. 
Click on Add a New Shutdown on the right side of the page. 
  A new page appears, allowing you to set all the parameters of the rule....