ADDER ePower Switch 1 Guard Manual

ePowerSwitch 1G
R2
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
User guide 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Version 02 2011 
                                                                                                                                              www.neol.com 
   

1 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
© Copyright by NEOL S.A.S - 4 Rue Nationale, 67800 BISCHHEIM, France 
 
Printed in France 
 
All rights reserved. No part of this documentation, accompanying software or other components of the 
described product may be reproduced or transmitted in any form or by any means, electronic or mechanical, 
including photocopying and recording, for any purpose other than the personal use of the purchaser without 
the express written permission of NEOL S.A.S....

 
2  
 
 
 
 
 
CONTENTS 
 
 
SAFETY INSTRUCTIONS: To be read before use! ...................................................................................... 3
 
1. DESCRIPTION .......................................................................................................................................... 4 
1.1 Diagram ............................................................................................................................................... 4 
1.2 Package list...

3 
SAFETY INSTRUCTIONS: To be read before use! 
 
  
NOTE 
 
• The ePowerSwitch devices can only be installed by qualified people with the following installation and 
use instructions. The manufacturer disclaims all responsibility in case of a bad utilization of the 
ePowerSwitch devices and particularly any use with equipments that may cause personal injury or 
material damage. 
• This equipment is designed to be installed on a dedicated circuit that must have a circuit breaker or fuse 
protection.  
•...

 
4
1. DESCRIPTION 
 
ePowerSwitch*1GR2 is a power control unit with a built-in Web server, an Ethernet and a RS232 
connection. It enables to control the power supply of 1 power outlet1s through an Ethernet connection.  
This unit offers additional IP device monitoring. It has a Real Time Clock to trigger scheduled actions and 
timestamp all events. Its serial interface enables to control the power outlet over a Terminal connection 
(KVM Switch, console server...) and to trigger a soft shutdown of a...

5 RS232 (SUB-D 9F Connector) 
Serial port RS232 with DB-9 female connector 
Pinout 
2 = TxD 
3 = RxD 
5 = Gnd 
 
 
The back of the ePowerSwitch 1G
R2 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
1.2 Package list 
 
The following items are included: 
 
‰  1 ePowerSwitch 1G
R2  
‰  1 power cable, 230 V / 10 Amp, length 1.80 Meters 
‰  1 RJ45 M/M cable, 2 Meters 
‰  1 serial cable SUB-D 9 points M/F, 1.80 Meters 
‰  1 quick installation guide 
‰  1 CD with User Guide, Quick Start Guide and Windows configuration program...

 
6
2. INSTALLATION 
 
Remark:  
Make sure that the ePowerSwitch 1GR2 is powered off. 
 
 
Connection instructions 
 
1.  Use a shielded
 RJ45 network cable to connect your ePowerSwitch 1GR2 to the network.  
 
2.  Use appropriated three-wire power cords (two poles plus ground) to connect your electrical device to 
the ePowerSwitch 1G
R2 unit.  
 
3.  Plug the power cable into a grounded 
socket. The Status LED lights on to confirm that power is on.  
 
4.  You can now configure the ePowerSwitch 1G
R2 by...

7 
3. CONFIGURATION 
 
To use the ePowerSwitch 1GR2 on your network, you must first configure its network parameters. Ask your 
network administrator for the parameters to use. 
 
There are three methods to configure the network parameters of the ePowerSwitch 1G
R2: 
 
3.1. Configuration through the LAN using the Finder program  
It is the simplest and fastest configuration method if you use Windows as operating system. It allows to 
configure your ePowerSwitch 1GR2 through your local network even if its...

 
8 DHCP: 
Check this box is you want to obtain the IP address, the subnet mask and the default gateway for your 
ePowerSwitch 1G
R2 via DHCP. 
Use of DHCP (Dynamic Host Configuration Protocol) requires a DHCP host to be set up on the 
network.  
IP Address: 
IP address of the ePowerSwitch 1G
R2, default is 192.168.100.200. 
Subnet Mask:  
Subnet Mask of the ePowerSwitch 1G
R2, default is 255.255.255.0. 
Gateway: 
Generally the address of your router, default is blank. 
DNS 1: 
Primary DNS (Domain Name...

9 
3.2. Configuration through an RS232 Terminal connection 
 
1.  Use the provided RS232 cable to connect the ePowerSwitch 1GR2 to an available serial port of your 
PC. 
 
2.  Run a Terminal program such as Windows HyperTerminal. 
 
3.  Configure the appropriate serial port @ 9.600, n, 8, 1 and no flow control. 
 
4.  On your computer, press  until the menu appears on your screen. 
 
5.  Press the “M” on your keyboard and follow the menu to configure the network parameters of your 
ePowerSwitch 1G
R2....