Adam Equipment Highland Portable Precision Balances HIGHLANDHCB User Manual

© Adam Equipment  Company 2 0 1 6   11 
5.0  FUNCTIONS  
5.1 PERCENTAGE WEIGHING  
The  balance  will allow a reference weight to be shown as 100%. Then any other 
weight placed on the balance  will be displayed as a percentage of the original 
sample.   
1)  Place your weight on the balance . 
2)  Press the [%]  key . The weight will be displayed as 100.00%.  
3)  Remov e the weight and place your next sample on the balance . The new 
reading will be shown as a percentage of the first value / reference...

© Adam Equipment  Company 2 0 1 6   12 
4) The  balance  will initially show  SP   10 asking for a sample size of 10 parts.  
Press  [Mode]  to cycle through the options: 10, 2 0, 50, 100, 200 and back to 10 
t o select the sample you have placed on the balance.   
5)  Press  [Smpl]  again once y ou have selected the sample. The display will show 
you the number. As more parts are  added the display will show the total 
number of parts (PCS  –  will be shown in the alpha -numeric display).   
6)  By p...

© Adam Equipment  Company 2 0 1 6   13 
5) Put a second weight on. I f set to automatic it will accumulate the weight 
automatically . If in manual  mode,  press [Print] , the display will show ACC   2  
foll owed by the new total in the memory for 2 seconds before returning to 
displaying the weight of the item on the  balance. 
6)  Continue until all weights have been added.  
To view the totals in memory press the  [Print] key when the balance  is at zero.  The 
display  will show ACC  xx  (where “...

© Adam Equipment  Company 2 0 1 6   14 
6.0  PARAMETERS  
Non -approved  balances ha ve 8  parameters that can be set  by the user. 
FUNCTION SECTION DESCRIPTION 
F1 UNT See section 6.1 Sets the units to be used 
g / ct / Lb / oz  / d / GN / OZt / dWt / MM / TL.T / TL.C / TL.t /t 
/ N /g2.  
F2 EL See section 6.2 Sets the backlight and audible alert beep (SW ver. 2.5 onwards) 
F3 SEr See section 6.3 Sets the print parameters  
F4 oFF See section 6.4 Sets the auto power-off parameter  
F5 IEC See section...

© Adam Equipment  Company 2 0 1 6   15 
4) Pressing the  [- >0/T

© Adam Equipment  Company 2 0 1 6   16 
6.2  SETTING THE BACKLIGHT AND AUDIBLE ALERT BEEP  
The backlight  and audible alert  may be enabled or disabled by the user. If the 
backlight is disabled, the battery life will be greater.  The followin g settings are 
available:  ( beep settings available in SW ver. 2.5 onwards)
 
bL  AU Sets the backlight to operate automatically when a weight is 
placed on the balance or a key is pressed. 
bL  Off Sets the backlight to be off. 
bL  On Sets the backlight to be...

© Adam Equipment  Company 2 0 1 6   17 
4) Press the [- >0/T0/T0/T

© Adam Equipment  Company 2 0 1 6   18 
Press the [Mode]  key to change the settin g. Press [->0/T0/T0/T

© Adam Equipment  Company 2 0 1 6   19 
2) After a few seconds, the display will show the first function F1   UNT .  
3)  Keep pressing the [Mode]  key until F4  oFF  is displayed. 
4)  Press the [- >0/T0/T0/T0/T

© Adam Equipment  Company 2 0 1 6   20 
6.6  ADJUST THE VALUE OF THE INTERNAL MASS (NOT POSSIBLE ON APPRO VED 
MODELS) 
The internal mass value stored in memory can be  adjusted to more clos ely match 
the value of the user’s  external mass.     
1)  To set this parameter press the  [Mode] key during self -checking test when 
turning on the balance . 
2)  After a few seconds, the display will show the first function F1   UNT .  
3)  Keep press ing the [Mode]  key until F6  CA is displayed. 
4)  Press the...