Adam Equipment GK Indicator GKREVL1 User Manual

							 
29                              © Adam Equipment Company 2013 
1.11.  ACCUMULATED TOTAL  
 
The  indicator  can  be  set  to  accumulate  when  a  weigh t  is  added  to  the  platform 
automatically or manually by pressing  [Print]. See Section 13.2. 
NOTE:    1. The  accumulation  function  is  available  only  during  weighing.    It  is  disabled 
during parts counting or percent weighing. 
 
2. The  accumulated  weights  will  be  stored  in  either  kg   or  lb,    depending  upon 
the weighing unit in use. 
 
3. If  at  any  time  the  weighing  units  are  changed,  the  accumulated  data  will  be 
lost. 
  
1.11.1  MANUAL ACCUMULATION 
 
When  the  indicator  is  set  to  manual  accumulation,  t he  weight  displayed  will  be 
stored in the memory when the  [Print] key is pressed and the weight is stable. 
 
·  Remove the weight and press   [Print] when the indicator is at zero. The 
display  will  show  "ACC 1" and  then  the  weight  in  memory  for  2  seconds 
before returning to normal.  The weight can be outp ut to a printer or PC 
using the RS-232 interface. 
 
 
 
    
						

							 
30                              © Adam Equipment Company 2013 
 
·   When  the  indicator  is  at  zero  place  a  second  weight   on  the  platform.  
When  stable  press  [Print] to  accumulate  the  weight.  The  display  will 
show  "ACC   2"  for 2 seconds and then show the new total. 
 
 
 
 
   
·  Continue until all weights have been added. This ca n continue for up to 
99 entries until the capacity of display is exceede d. 
 
·  To view the total in memory press the   [Print] key when the indicator is 
at  zero.    The  display  will  show  the  total  number  of   accumulation "ACC  
xx"  and the total weight before returning to zero.  
 
·  To  print  the  total,  press  [Print]  to  recall  and  then  immediately  press 
[Print]  the second time to print the results. 
 
·  To  erase  the  memory,  press   [Print] to  view  the  total  and  then 
immediately press  [CE] to clear the memory. 
    
						

							 
31                              © Adam Equipment Company 2013 
  
1.11.2 AUTOMATIC ACCUMULATION 
 
When  the  indicator  has  been  set  to  Automatic  Accumu lation  the  value  is  stored  in 
memory automatically.     
 
·   Place a weight on the platform. The beeper will sou nd when the display 
is stable indicating the value is accepted.  Remove  the weight. 
 
·  The display will show  "ACC 1" and then the total in the memory before it 
returns to zero.   Adding a 2nd weight will repeat  the process. 
  
·  While  the  weight  is  on  the  platform,  press  the  [Print] key  to  view  the 
values- first the accumulation number  "ACC x" and then the total will be 
shown.  
 
 NOTE:  
  1. The indicator will not show the value when a wei ght is removed. 
2.  In  all  cases  the  display  must  return  to  zero  or  a  negative  number, 
before another sample can be added to the memory.  
3.  More  products  can  be  added  and  [Print] be  pressed  again  for  up  to 
99 entries until the capacity of display is exceede d.  
						

							 
32                              © Adam Equipment Company 2013 
 
RS-232 SPECIFICATION 
The  GK  indicator  is  supplied  with  bi-directional  RS -232  interface  as  standard.  The 
indicator  when  connected  to  a  printer  or  computer  o utputs  the  weight  with  the 
selected weighing unit through the RS-232 interface . 
  Default Specifications: 
            
Connector:          
 
     
The indicator can be set to print text in English,  French, German or Spanish.  See the 
RS-232 parameters section for details. 
RS-232 output of weighing data 
ASCII code  
9600 Baud (user selectable) 
8 data bits  
No Parity 
9 pin d-sub miniature socket 
  Pin 3  Output  
  Pin 2  Input  
  Pin 5  Signal Ground  
						

							 
33                              © Adam Equipment Company 2013 
LABEL = On  Label Formats are printed  
Data Format-Normal Output:  
Only  weight  value  along  with  the  weighing  unit  is  p rinted.    If  Percent  weighing  is 
used then % is shown in place of weighing units.    
Data Format-Parts Counting Output:  
Weight, Unit weight and number of parts are printed . 
                     
 
Date           12/09/2006  
Time           14:56:27     
  
Scale ID    123456     
         If ID is zero, it is left blank 
User ID    234567       
  
Net Wt         1.234 kg   
         Net Wt. (or Gross Wt.) 
                      
 
 

  
						

							 
34                              © Adam Equipment Company 2013 
 
                     
  
Date           12/09/2006   
Time           14:56:27    
 
Scale ID    123456      
User ID    234567      
  
Net Wt.        1.234 kg         
Net Wt. (or Gross Wt.) 
Unit Wt.         123 g     g    
for metric and lb for pounds 
PCS               10 pcs    
                     
  
						

							 
35                              © Adam Equipment Company 2013 
  
Data Format- Memory Recall Output:    
Data Format- Continuous Output- Normal weighing:    
Data Format- Continuous Output- Parts Counting:   
 
Date            12/09/2006   
Time            14:56:27    
 
Scale ID   123456      
User ID     234567      
 
------------------
                                     
TOTAL  
No.               5        
Wt.           1.234 kg     
PCS              10 pcs    
                       
------------------ 
 
        
     
Net    1.234 kg             Net Weight (or Gross wt.) 
                              
 
Net    1.234 kg          Net Weight (or Gross wt.) 
U.W.     123 g           kg and g for metric and Lb for pounds 
PCS       10 pcs  
                              
    
						

							 
36                              © Adam Equipment Company 2013 
LABEL = Off  single line output  
Fixed line width, leading zeros are spaces.  
 Data Format-Normal Output: 
 Data Format- Memory Recall Print: 
NOTE: 
  1. The  accumulated  total  will  not  be  sent  to  the  RS-23 2  when  the  continuous 
print is turned on.   
 
2. The continuous print will only be for the current w eight and the display data.  
 
3. In other languages the format is the same but the t ext will be in the language 
selected. 
  4. When the scale is in the Lb:oz weighing unit the RS -232 output will only show 
pounds.   10lb:8oz  will be printed as 10.5 lb. 
  1.234 Kg 
TOTAL No.     5,   1.234 Kg,        10 pcs 
  
						

							 
37                              © Adam Equipment Company 2013 
 
Description  ENGLISH  FRENCH  GERMAN   SPANISH  
Net weight  Net Wt.  Pds Net  Net-Gew  Pso Net 
Weight per unit  
counted  Unit Wt.  Pds unit  Gew/Einh  Pso/Unid 
Number of items 
counted  Pcs  Pcs  Stck.  Piezas 
Number of  
weighing  added  
to subtotals  No.  Nb.  Anzhl  Num. 
Total weight and 
count printed  Total  Total  Gesamt  Total 
Print date  Date  Date  Datum  Fecha 
Print time  Time  Heure  Zeit  Hora 
Scale ID number  Scale ID  Bal ID  Waagen ID  Bal ID 
User ID Number  User ID  Util ID  Nutzer ID  Usuario ID 
  
						

							 
38                              © Adam Equipment Company 2013 
 
1.12.  INPUT COMMANDS FORMAT 
  
The indicator can be controlled with the following  commands. Press the [Enter] key 
of the PC after each command.     
T    Tares  the  indicator  to  display  the  net  weight.  This
  is  the  same  as 
pressing  [Tare]. 
 
Z     Sets the zero point for all subsequent weighing. Th
e display shows 
zero.   
P      Prints  the  results  to  a  PC  or  printer  using  the  RS-
232  interface.  It 
also  adds  the  value  to  the  accumulation  memory  if  t he 
accumulation function is not set to automatic.