Adam Equipment ABK Bench Weighing Scales User Manual

EN 
© Adam E\buipm\fnt Company 2015 9      3116611621R\fvA1-F\fb15  
 
6.0  OPERATION 
6.1 ZEROIN\f THE DISPL\bY  
 
·  You can press the  [Z/T] key at any time to set the display to zero. 
This  will  usually  be  when  the  platform  is  empty.  When  the  zero 
point is obtained the display will show an indicator for zero. 
 
 
 
 
·  The  scale  has  an  automatic  re-zeroing  function  to  account  for 
minor  drifting  or  accumulation  of  material  on  the  platform. 
However you may need to...

EN 
© Adam E\buipm\fnt Company 2015 10      3116611621R\fvA1-F\fb15  
 
·  Press the  [Z/T]  key  to tare  the  scale. The  weight  is deducted  and 
stored  as  the  tare  value  leaving  zero  on  the  display.  The  “ NET” 
indicator will be ON and as a product is added only the net weight 
of  the  product  will  be  shown.  The  scale  could  be  tared  a  second 
time  if  another  type  of  product  was  to  be  added  to  the  first  one. 
Again only the weight that is added after taring will be...

EN 
© Adam E\buipm\fnt Company 2015 11      3116611621R\fvA1-F\fb15  
 
6.4  P\bRTS
 COUNTIN\f 
 
If parts counting is enabled, See section 7.4 in the full manual, it is possible to 
count  parts  using  a  sample  of  the  parts  to  determine  an  average  piece 
weight.   
 
·  If  using  an  empty  container,  place  the  container  on  the  top  pan 
and  press  [Z/T] to  zero  the  display.  Press  the  [PCS]  key  to  enter 
parts counting mode.  
 
·  The scale will show “ P      10”. Change the...

EN 
© Adam E\buipm\fnt Company 2015 12      3116611621R\fvA1-F\fb15  
 
6.6 \bCCUMUL\bTED TOT\bL 
 
·  The  scale  can  be  set  to  accumulate  manually  by  press
 ing  the 
[Print/M+/Esc]   key,  or  automatically  when  a  weight  is  removed 
from the scale.  See the Section 7.3 of the full manual for details. 
 
 
6.7  PERCENT\b\fE
 WEI\fHIN\f  
 
The scale can be set to perform percentage weighing. See Section 7.2 of the 
full version of the user manual for complete details. 
 
6.8  \bNIM\bL...

EN 
© Adam E\buipm\fnt Company 2015 13      3116611621R\fvA1-F\fb15  
8.0  BATTERY OPERATION 
 
·  The  scales  can  be  operated  from  the  battery  if  desired.  The 
battery life can be up to 70 hours depending on the load cells and 
how the backlight is used.  
 
·  A  battery  symbol  is  shown  on  the  display  which  indicates  the 
current  charge  of  the  battery,  3  bars  means  fully  charged.  When 
just  the  outline  of  the  battery  and  no  bars  are  visible  the  battery 
needs to...

EN 
© Adam E\buipm\fnt Company 2015 14      3116611621R\fvA1-F\fb15  
312
4
  The RS-232 serial interface is a plug as figure 2 shows: 
       1: Pin GND,    Signal Ground 
2: Pin RXD,    Received Data 
          3: Pin TXD,    Transmitted Data 
 
 
          
As viewed from the back of the indicator 
 
The  scale  can  be  set  to  print  text  in  English,  French,  German  or  Spanish.  
See the RS-232 parameters section of the full user manual for details. 
 
The data format and examples of printouts...

EN 
© Adam E\buipm\fnt Company 2015 15      3116611621R\fvA1-F\fb15  
 
11.0  CALIBRATION 
  
The  scale  can  be  calibrated  using  the  following  procedure.  To  enter  this 
procedure  it  is  necessary  to  use  Func  4  which  is  accessible  using  the 
[Func/C]   key  as  described  in  section  7.4  in  the  full  manual,  or  by  using  the 
passcode access as described in section 12.0. 
 
The  scales  calibrate  using  either  metric  or  pound  weights  depending  on  the 
weighing  unit...

EN 
© Adam E\buipm\fnt Company 2015 16      3116611621R\fvA1-F\fb15  
 
12.0  SERVICE PARAMETERS 
 
 
 
 
The  scales  will  allow  entry  to  the  parameters  if  the  [Tare]  key  is  pressed 
during the power on cycle. The passcodes work as explained earlier. 
In this case the display will show the passcode request screen, “  P  -  -  -  - “ .  To 
continue enter a passcode as described below.  
 
Entering passcode 0000 will allow calibration as shown in section 11. 
 
Entering  1000  will  allow...

EN 
© Adam E\buipm\fnt Company 2015 17      3116611621R\fvA1-F\fb15  
13.0  ERROR CODES 
 
ERROR  
CODES 
DESCRIPTION SUGGESTIONS 
- -oL - - Over-range Remove weight from the scale.   
 
If  the  problem  persists  contact  your  dealer  or  Adam 
Equipment for assistance. 
  
Err 1 Time Setting Error Enter  time  using  correct  format  and  reasonable  values. 
Format: hh:mm:ss 
 
Err 2 Date Setting Error Enter  date  using  correct  format  and  reasonable  values. 
Format: yy:mm:dd 
 
Err 4 Zero...

EN 
© Adam E\buipm\fnt Company 2015 18      3116611621R\fvA1-F\fb15  
WARRANTY INFORMATION    
Adam  Eqñ“ipment  offers  Limited  Warranty  (Parts  and  Laboñ“r)  for  the  components  failed  dñ“e  to  defects 
in materials or ñòorkmanship.  Warranty starts from the date of delivery. 
Dñ“ring the ñòarranty period, shoñ“ld any repairs be necessary, the pñ“rchaser mñ“st inform  its sñ“pplier or 
Adam  Eqñ“ipment  Company.  The  company  or  its  añ“thorised  Technician  reserves  the  right  to  repair...