Acer Travelmate 340 Service Guide

Chapter 345
Removing the External  DIMM Module
1.Remove the two screws holding the external DIMM cover.
2.Lift the cover out to remove the DIMM module.
   
340SG.book  Page 45  Thursday, October 28, 1999  10:51 AM 

46Chapter 3
Removing the LCD Module
Removing the Middle Cover
1.First remove the two screws from the rear of the unit. 
2.Push the release button to release the middle cover gently.
3.Pull the middle cover up. 
4.Disconnect the speaker cable from the main board and lift the middle cover away. 
Removing the Speaker
1.First, remove the screw. 
2.Remove the speaker plate with the speaker from the middle cover
3.Separate the speaker plate from the speaker.
Disassembling the LCD module
1.Disconnect the...

Chapter 347
4.Close the LCD module.
5.Remove the two screws on the base of the unit
6.Open the LCD to remove the LCD module from the main unit.
7.Remove the two camera rubbers from the LCD.
8.Remove the four cushions.
9.Remove the four screws from the LCD bezel.
10.Snap off the LCD bezel carefully and gently remove the LCD bezel from the LCD module.
11.Remove the two screws from the hinges.
12.Remove the hinges from the LCD module.
13.Detach the hinge caps from the hinges.
14.Remove the six screws from...

48Chapter 3
16.Turn the LCD over and disconnect the LCD power connector from the inverter.
17.Disconnect the inverter cable from the inverter.
18.Disconnect the LCD FPC cable from the LCD.     
340SG.book  Page 48  Thursday, October 28, 1999  10:51 AM 

Chapter 349
Disassembling the Main Unit
Removing the Keyboard
1.Pull out and upward to expose the keyboard.
2.Disconnect the keyboard cable from the main board.
3.Remove the keyboard from the main board.
  
Removing the DIMM Module
1.Remove the two screws from the DIMM cover.
2.Remove the DIMM cover from the main unit. 
3.Use two flat bladed screw drivers to push out the latches on both sides of the DIMM socket .
4.Remove the DIMM module from the main unit.
Removing the Modem Combo Board
1.Remove the...

50Chapter 3
3.Pull the modem combo board out from its socket. 
4.Disconnect the network cable from the modem combo board.
Removing the RTC
1.Use a plastic flat bladed screw driver to remove the RTC battery from its socket.
NOTE: To replace the RTC battery, press the RTC battery into the socket.
Removing the Lower Case
1.Remove the three screws, and the 11 screws on the base of the unit .
2.Remove the lower case from the main unit.
340SG.book  Page 50  Thursday, October 28, 1999  10:51 AM 

Chapter 351
3.Disconnect the touch pad cable from the main board.
4.Turn the unit over to remove the 4 screws on the CPU lower holder.
5.Remove the CPU lower holder from the main board.
Removing the Main Board
1.Remove the 4 screws on the mother board as shown below.
2.Turn the main board over and put it on the side of the upper case. 
3.Remove then fan cable from the main board.
4.Remove the main board from the upper case.
5.Remove the harddisk drive board from the main board.
6.Gently, remove the...

52Chapter 3
Removing the Touchpad Board
1.Remove the two screws from the touchpad bracket.
2.Remove the touchpad bracket from the upper case.
3.Disconnect the touchpad cable from the touchpad board.
4.Remove the touchpad board from the upper case.
340SG.book  Page 52  Thursday, October 28, 1999  10:51 AM 

Chapter 453
Use the following procedure as a guide for computer problems.
NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or 
modified options can give false errors and invalid system responses.
1.Obtain the failing symptoms in as much detail as possible.
2.Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating 
the same operation.
3.Use the following table with the verified symptom to determine...

54Chapter 4
System Check Procedures
External Diskette Drive Check
Do the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is 
required.
NOTE: 
Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause 
damage to the drive or cause the drive to fail. 
Do the following to select the test device. See “Running PQA Diagnostics Program” on page 37 for details.
1.
Boot from the diagnostics diskette and start...