Acer Projector Pd527 User Manual

9... English

Introduction

 Connection Ports
1.  RS232 Connector
2.  USB Connector
3.  Monitor Loop-through Output Connector (VGA-Out)
4.  Audio Input Connector
5.  Composite Video Input Connector
6.  S-Video Input Connector
7.  PC Analog Signal/HDTV/Component Video Input Connector
8.  DVI Input Connector (for Digital signal with HDCP function) (Op-
tional)
9.  KensingtonTM Lock Port
Below items are for PD525PW/PD527W only:
10.  Lan (RJ45 Port for 10/100M Ethernet)
11.  Audio Output Connector
12....

10English ...
Introduction
1.  Laser Pointer
2.  Power
3.  Laser Button
4.  Source
5.  Resync
6.  Freeze 
7.  Hide
8.  Mute
9.  Aspect Ratio
10.  Keystone/Four Directional  
  Select Keys
11.  Back
12.  Digital Zoom
13.  Menu
14.  Mouse Left Click
Remote Control with  Laser Pointer
15.  Mouse Right Click
16.  Mouse
17.  Empowering Key
18.  Volume +
19.  Volume -
20.  Page Up
21.  Page Down
22.  VGA
23.  S-Video
24.  Video
25.  Component
26.  DVI
27.  Wireless or Language 
28.  Transmit Indicator Light...

11... English

Installation
1. ....................................................................................................................Power Cord2. .....................................................................................................................VGA Cable3. ...............................................................................................Composite Video Cable4....

12English ...

Installation

1
1. ....................................................................................................................Power Cord2. .......................................................................................................................Lan Cable3. ...............................................................................................Audio Cable Jack/RCA4....

13... English

Installation

Power/Standby
Powering On the Projector
1.  Remove the lens cap.
2.  Ensure that the power cord and signal cable are securely connected.  The Power LED will flash 
red.
3.  Turn on the lamp by pressing “Power/Standby” button on 
the control panel.And the Power LED will turn blue.
4.  Turn on your source (computer, notebook, video player 
,etc.).  The projector will detect your source automatically.
 If the screen displays "Lock" & "Source" icons, it means...

14English ...

Installation

Warning Indicator
 When the “LAMP” indicator lights solid red, the projector will 
automatically shut itself down.  Please contact your local reseller 
or service center.
 When the “TEMP” indicator lights solid red for about 20 sec-
onds, it indicates the projector has been overheated.  You will see 
a message “Projector Overheated. Lamp will automatically turn 
off soon.” on the on-screen display.  The projector will automati-
cally shut itself down.
  Under normal...

15... English

Installation

Adjusting the Projected Image
Adjusting the Projector Image Height
Elevator Foot 12Elevator Button
The projector is equipped with an elevator foot for adjusting 
the image height.
 To raise the image:
1.  Press the elevator button 
.
2.  Raise the image to the desired height angle  , then release 
the button to lock the elevator foot into position.
 To lower the image:
1.  Press the elevator button.
2.  Lower the image, then release the button to lock the elevator  
  foot...

16English ...

Installation
0D[FPFPFPFPFPFP
0LQ FP FP FP FPFP FP
0D[:[+[
[FP[
[FP[
[FP[ [FP[[FP[ [FP
0LQ:[+ [
[FP [
[FP...

17... English

User Controls
Remote ControlControl Panel
Control Panel & Remote Control
There are two ways for you to control the functions: Re-
mote Control and Control Panel.
 Using the Control Panel
 Power
  Refer to the “Power On/Off the Projector” section on pages    
    13-14.
  Resync
  Automatically synchronizes the projector to the input source.
 Source 
  Press “Source” to choose RGB, Component-p, Component-i,    
    S-Video, Composite, DVI-D (Optional), Video and HDTV    
    sources....

18English ...

User Controls

     Using the Remote Control
 Power 
  Refer to the “Power On/Off the Projector” section on pages  
    13-14
 Laser Button  
  Aim the remote at the viewing screen, press and hold this  
    button to activate the laser pointer. 
 Resync
  Automatically synchronizes the projector to the input source.
 Source 
  Press “Source” to choose RGB, Component-p, Component-i,  
    S-Video, Composite Video , DVI-D (Optional)and HDTV  
    sources.
 Freeze
  Press “Freeze” to...