Acer Extensa 710 Service Guide

Chapter 2 2-11
To exit Hibernation mode, press the power switch. The computer also 
resumes from Hibernation mode if the resume timer is set and matched. The 
computer also resumes via the network if the Wake On LAN parameter is 
enabled.
Note: Do not change any devices (such as add memory or swap hard 
disks) when the computer is in Hibernation mode
.
700SG-2.fm  Page 11  Monday, June 8, 1998  1:26 PM 

2-12 EXTENSA 700/710 Service Guide
Advanced Power Management
This computer supports the APM standard designed to further reduce power 
consumption. APM is a power-management approach defined jointly by 
Microsoft and Intel. An increasing number of software packages support APM 
to take advantage of its power-saving features and allows greater system 
availability without degrading performance.
For more information about APM under Windows 95, refer to your Windows 
95 user’s manual.
Note: If you enable...

Chapter 2 2-13
PhDISK
The PhDISK utility allows your computer to enter hibernation mode. Before 
entering hibernation mode, your computer saves all necessary computer 
information into a file or partition created by PhDISK, then shuts off power to 
all system components. On the next startup, the computer reloads the 
information from the PhDISK file or partition and resumes from where you left 
off.
Note: By default, this program is automatically loaded and set up on your 
computer so you do not need to...

2-14 EXTENSA 700/710 Service Guide
700SG-2.fm  Page 14  Monday, June 8, 1998  1:26 PM 

Chapter 3 3-1
This chapter contains procedures on how to disassemble the notebook 
computer for maintenance and troubleshooting.
To disassemble the computer, you need the following tools:
•  Wrist grounding strap and conductive mat for preventing electrostatic 
discharge
•  Flat-bladed screwdriver
•  Phillips screwdriver
•  Hexagonal screwdriver
•  Twee z er s
•  Plastic stick
The flowchart on the following page gives a clearer and more graphic 
representation off the entire disassembly sequence. Please...

3-2 EXTENSA 700/710 Service Guide
HDD
Module
CD-ROM
M o du le or
L S 12 0, D V D
Middle
Cover
LC D
Hinge
Cover
Battery
Cover
DIM M
Door
MODEM
Door
Keyboard
Upper
Heat Sink
DIM M
Board
MODEM
Board
Battery
Pack
Machine
CaseTo p  C o v e r
LC D
ModuleLC D
Bezel
LCD
Panel
Lower
Case
To u c h P a d
Bracket
L e ft  o r R ig h t
C hannel Speaker
To u c h P a d
ButtonTo u c h P a d
CP U
Heat SinkIM M
ModuleIM M
S h ie ldFa n
FDD
Module
Main
Board
ID E
Board
DC-DC &  Charger
Board
PCM CIA
Socker
In te r n a l...

Chapter 3 3-3
Installing Memory
Disassembling the DIMM module:
1.  To remove the DIMM module, remove the screw from the DIMM cover.
2.  Use a tweezers to remove the cover.
3.  Use a flat-bladed screwdriver to push out the locks at both sides of the 
DIMM socket.
4.  Remove the DIMM module.
Disassembling the modem board
1.  Remove the modem board by removing the screw.
2.  Pull out the cover gently.
3.  Remove the modem board using a flat-bladed screwdriver.
4.  Reconnect the modem board to CN26 & CN27 on...

3-4 EXTENSA 700/710 Service Guide
Removing the Hard Disk Drive
1.  To remove the internal hard disk drive, remove the screw with a flat-bladed 
screwdriver or a coin.
2.  Carefully pull out the hard disk drive cover to remove.
Disassembling the hard disk drive:
1.  To disassemble the hard disk module, remove the 2 screws on both sides 
of the hard disk drive.
2.  Separate the hard disk drive from its bezel.
3.  Remove the hard disk drive from it’s shield plate
4.  Disconnect the hard disk cable from the...

Chapter 3 3-5
Removing the battery pack:
1.  To remove the battery pack, press the battery compartment cover latch 
and slide the cover out. 
2.  Pull out the battery pack.
3.  To reinsert the battery pack, slide in the battery pack.
4.  And slide the battery compartment cover into its place.
Disassembling the CD-ROM drive:
1.  Push the CD-ROM drive locker forward and carefully pull out the CD-ROM 
module.
2.  To disassemble the CD-ROM module, remove the 2 screws from both 
sides of the CD-ROM module and...

3-6 EXTENSA 700/710 Service Guide
Removing the keyboard
1.  Remove the hinge cover by sliding it out.
2.  Remove the middle cover by using a flat-bladed screwdriver to release the 
latches.
3.  Lift the cover to remove
4.  Replace the middle cover.
5.  The latches of the middle cover and the upper case must be matched, 
then place it into position.
6.  Pull the keyboard up and outward to expose the keyboard connector at 
CN22.
7.  The keyboard can be removed by releasing this connector.
700SG-3.fm  Page...