Acer Extensa 5630z Service Guide

							Chapter 245
The table below describes the parameters in this screen. Settings in boldface are the default and suggested 
parameter settings.
NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget 
your password. If you forget your password, you may have to return your notebook computer to your 
dealer to reset it.
Setting a Password
Follow these steps as you set the user or the supervisor password:
1.Use the “w” and “y” keys to highlight the Set Supervisor Password parameter and press the e key. The 
Set Supervisor Password box appears:
2.Type a password in the “Enter New Password” field. The password length can not exceeds 8 
alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New 
Password” field.
IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen.
3.Press e.
                After setting the password, the computer sets the User Password parameter to “Set”.
4.If desired, you can opt to enable the Password on boot parameter.
5.When you are done, press u to save the changes and exit the BIOS Setup Utility.
ParameterDescriptionOption
Supervisor Password Is Shows the setting of the Supervisor password
Clear or Set
User Password Is Shows the setting of the user password.
Clear or Set
HDD Password Is Shows the setting of the hard disk password.
Clear or Set
Set Supervisor Password Press Enter to set the supervisor password. 
When set, this password protects the BIOS 
Setup Utility from unauthorized access. The 
user can not either enter the Setup menu nor 
change the value of parameters.
Set User Password Press Enter to set the user password. When 
user password is set, this password protects 
the BIOS Setup Utility from unauthorized 
access. The user can enter Setup menu only 
and does not have right to change the value of 
parameters.
Set HDD Password Enter HDD Password.
Password on Boot Defines whether a password is required or not 
while the events defined in this group 
happened. The following sub-options are all 
requires the Supervisor password for changes 
and should be grayed out if the user password 
was used to enter setup.
Disabled or Enabled 
						

							46Chapter 2
Removing a Password
Follow these steps:
1.Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The Set 
Password box appears:
2.Type the current password in the Enter Current Password field and press e.
3.Press e twice without typing anything in the Enter New Password and Confirm New Password fields. The 
computer then sets the Supervisor Password parameter to “Clear”.
4.When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.
Changing a Password
1.Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The Set 
Password box appears:
2.Type the current password in the Enter Current Password field and press e.
3.Type a password in the Enter New Password field. Retype the password in the Confirm New Password 
field.
4.Press e. After setting the password, the computer sets the User Password parameter to “Set”.
5.If desired, you can enable the Password on boot parameter.
6.When you are done, press u to save the changes and exit the BIOS Setup Utility.
If the verification is OK, the screen will display as following. 
The password setting is complete after the user presses u. 
						

							Chapter 247
If the current password entered does not match the actual current password, the screen will show you the 
Setup Warning.
If the new password and confirm new password strings do not match, the screen will display the following 
message. 
						

							48Chapter 2
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices 
includes the diskette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay.
Phoenix SecureCore(tm) Setup Utility
Main
Item Specific Help
Useorto
select a device, then
presstomoveit
up the list, or 
to move it down the
list. Press  to
escape the menu. Boot priority order:
F1
EscHelp
ExitSelect Item
Select Menu
Change Values
Select Sub-Menu -/+
EnterF9
F10Setup Defaults
Save and Exit
Information Security Boot Exit
2:
3:
4:
5:
6:
7:: XXXXXXXXXXX-XXX XX-XXXX-XX
PCI LAN: Network Boot
USB HDD:
USB FDD:
USB Key:
USB CDROM: 1: IDE HDD: XXXXXXXXXXX-(XX)
IDE CD 
						

							Chapter 249
Exit
The Exit screen contains parameters that confirmed or discard the changes made to the parameters in the 
BIOS Setup Utility.
The table below describes the parameters in this screen.
ParameterDescription
Exit Saving Changes Exit System Setup and save your changes to CMOS.
Exit Discarding Changes Exit utility without saving setup data to CMOS.
Load Setup Default Load default values for all SETUP item.
Discard Changes Load previous values from CMOS for all SETUP items.
Save Changes Save Setup Data to CMOS.
Phoenix SecureCore(tm) Setup Utility
Main
Item Specific Help
Exit System Setup and
save your changes to
CMOS.
F1
EscHelp
ExitSelect Item
Select Menu
Change Values
Select Sub-Menu -/+
EnterF9
F10Setup Defaults
Save and Exit
Information Security
BootExit
Exit Discarding Changes
Load Setup Defaults
Discard Changes
Save Changes Exit Saving Changes 
						

							50Chapter 2
BIOS Flash Utility
The BIOS flash memory update is required for the following conditions:
qNew versions of system programs
qNew features or options
qRestore a BIOS when it becomes corrupted. 
Use the Flash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery 
Diskette before you use the Flash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Flash.
NOTE: Please use the AC adaptor power supply when you run the Flash utility. If the battery pack does not 
contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not 
completely loaded. 
Fellow the steps below to run the Flash.
1.Prepare a bootable diskette.
2.Copy the flash utilities to the bootable diskette.
3.Then boot the system from the bootable diskette. The flash utility has auto-execution function. 
						

							Chapter 251
Remove HDD/BIOS Utility
This section provide you with removing HDD/BIOS method:
Remove HDD Password:
qIf you key in wrong HDD password for three time, “HDD password error code” would display on the 
screen. See the image below.
qIf you need to solve HDD password locked problem, you can run HDD_PW.EXE
1.
Key in “hdd_pw 15494 0”
2.Select “2”
3.Choose one upper-case string
qReboot system and key in “0KJFN42” or “UVEIQ96” to HDD user password. 
						

							52Chapter 2
Remove BIOS Password:
qIf you key in wrong Supervisor Password for three time, “System Disabled” would display on the 
screen. See the image below. 
						

							Chapter 253
qIf you need to solve BIOS password locked problem, you can run BIOS_PW.EXE
1.
Key in “bios_pw 14452 0”
2.Choose one upper-case string
qReboot the system and key in “qjjg9vy” or “07yqmjd” to BIOS user password. 
						

							54Chapter 2