Acer Aspire One Model Nav Service Guide

							Chapter 371
 LCD Module Disassembly Process
IMPORTANT: Cable paths and positioning may not represent the actual model. During the removal and 
replacement of components, ensure all available cable channels and clips are used and that the cables are 
replaced in the same position.
NOTE: The product previews seen in the disassembly procedures may not represent the final product color or 
configuration. The following procedure outlines the steps to disassemble the LCD Module on models with 3G 
functionality. Models that do not support 3G do not require the removal of the yellow and blue Antenna cables 
detailed below.
LCD Module Disassembly Flowchart
Screw List
StepScrewQuantityPart No.
LCD Bezel M2*4 2 86.SAS02.002
LCD Panel M2*4 4 86.SAS02.002
LCD Brackets M2*3 4 86.SAS02.001
Remove
LCD Panel
Remove
LCD Bezel
Remove
Microphone Set
Remove LCD
Panel f rom Main
Unit bef ore
proceeding
Remove
LCD Panel
BracketsRemove
WLAN Antennas
Remove
Camera Module 
						

							72Chapter 3
Removing the LCD Bezel
1.See “Removing the LCD Module” on page 69.
2.Remove the two (2) screw caps and two (2) screws from the LCD Bezel.
3.Carefully pry the LCD Bezel from the LCD Assembly using both hands. If necessary, use a plastic pry to 
release the corners of the bezel. When all the guide hooks have been released, lift the bezel clear of the 
assembly.
StepSizeQuantityScrew Type
LCD Bezel M2*4 2 
						

							Chapter 373
Removing the Camera Board
1.See “Removing the LCD Bezel” on page 72.
CAUTION: Do not use excessive force when handling the Web Camera Board.
2.Disconnect the cable from the Web Camera Board as shown.
3.Detach the Web Camera Board while being careful not to handle the board with excessive force. 
						

							74Chapter 3
Removing the LCD Panel
1.See “Removing the Camera Board” on page 73.
2.Remove the four (4) securing screws from the LCD Panel.
3.Remove the LVDS foil tab and pull the LVDS cable away from the channel as shown.
4.Lift the LCD Panel clear of the LCD Bracket.
StepSizeQuantityScrew Type
LCD Panel M2*4 4 
						

							Chapter 375
Removing the Microphone Set
1.See “Removing the LCD Panel” on page 74.
2.Remove the foil tabs from the Microphone set while lifting the cable away from the cable channel. 
3.Continue removing the foil tabs and pulling the cable away. The cable channel is highlighted between the 
green lines.
4.Peel back the foil tab and lift the Microphone set clear of the device. 
						

							76Chapter 3
Removing the WLAN Antennas
1.See “Removing the LCD Panel” on page 74.
2.Peel back the foil tabs on the black antenna cable. 
3.Pull the cable away from the cable channel, which is highlighted between the green lines.
4.Pry the antenna pad clear of the bracket. 
						

							Chapter 377
5.Peel back the foil tabs on the white antenna cable. 
6.Pull the cable away from the cable channel, which is highlighted between the green lines.
7.Pry the antenna pad clear of the bracket. 
						

							78Chapter 3
Removing the LCD Brackets
1.See “Removing the Microphone Set” on page 75.
2.Turn the LCD Panel over and peel away the LVDS cable. 
3.Detach the clear connector tape and disconnect the LVDS cable.
4.Remove four (4) screws that secure the LCD Panel.
StepSizeQuantityScrew Type
LCD Brackets M2*4 4 
						

							Chapter 379
5.Remove two (2) brackets from the LCD Panel. 
						

							80Chapter 3
LCD Module Reassembly Procedure
Replacing the LCD Brackets
1.Replace two (2) brackets to the LCD Panel.
2.Secure the LCD Panel using four (4) screws.
3.Connect the LVDS cable to the LCD Panel and reattach the clear connector tape.