Acer Aspire 5737z Service Guide

							Chapter 381
 LCD Module Disassembly Process
LCD Module Disassembly Flowchart
Screw List
StepScrewQuantityPart No.
LCD Bezel M2.5*6 4 86.AZ802.003
Inverter Board M2.5*6 1 86.AZ802.003
LCD Panel M2.5*6 2 86.AZ802.003
LCD Brackets M2*3 8 86.AZ802.002
Rem ove
Inverter BoardRem ove
LCD Panel
Rem ove
LCD Bezel
Rem ove
LCD FPC Cable
Remove LCD
Panel from  Main
Unit before
proceeding
Rem ove
LCD BracketsRem ove
Antennas
Rem ove
Camera Module
Rem ove
Microphone 
						

							82Chapter 3
Removing the LCD Bezel
1.See “Removing the LCD Module” on page 61.
2.Remove the two upper and two lower bezel screw caps and screws.
NOTE: The two center caps are protection only and do not cover screws.
 
3. Starting from the lower right side of the bezel, pry the bezel upwards and away from the panel. Move along the 
top and right until all sides of the bezel are removed.
NOTE: If necessary, use a pry to lift up the outside edges of the bezel. 
StepSizeQuantityScrew Type
LCD Bezel M2.5*6 4 
						

							Chapter 383
Removing the Inverter Board
1.See “Removing the LCD Bezel” on page 82.
2.Remove the single securing screw from the Inverter Board.
3.Disconnect the right Inverter Board cable as shown.
4.Disconnect the left Inverter Board cable as shown.
StepSizeQuantityScrew Type
Inverter Board M2.5*6 1 
						

							84Chapter 3
5. Remove the Inverter Board from the LCD module. 
						

							Chapter 385
Removing the Camera Module
1.See “Removing the LCD Panel” on page 86.
2.Disconnect the camera cable.
3.Remove the Camera from the module. 
						

							86Chapter 3
Removing the LCD Panel
1.See “Removing the Inverter Board” on page 83.
2.Disconnect the camera cable.
3.Remove the two securing screws from the LCD Panel.
4.Remove the adhesive tapes securing the Inverter cables to the module.
StepSizeQuantityScrew Type
LCD Panel M2.5*6 2 
						

							Chapter 387
5.Lift the LCD Panel clear of the module.
The LCD Module appears as follows when the LCD Panel is removed. 
						

							88Chapter 3
Removing the LCD Brackets and FPC Cable
1.See “Removing the LCD Panel” on page 86.
2.Remove the eight securing screws (four on each side) from the LCD Panel brackets.
3.Remove the LCD brackets by pulling away from the LCD Panel.
4.Turn the LCD panel over to expose the rear.
5.Lift the adhesive protector and disconnect the cable from the LCD Panel.
6.Lift the FPC cable from the panel.
StepSizeQuantityScrew Type
LCD Brackets M2*3 8 
						

							Chapter 389
Removing the Microphone Module
1.See “Removing the LCD Panel” on page 86.
2.Remove the strips holding the microphone cable in place. Ensure the cable is free from obstructions.
3.Lift the Microphone Module clear of the module. 
						

							90Chapter 3
Removing the Antennas 
1.See “Removing the LCD Panel” on page 86.
2.Remove the strips holding the antenna cables in place. Ensure the cables are free from obstructions.
3.Remove the adhesive tape and lift the left side antenna from the LCD module as shown.
4.Remove the adhesive tape and lift the left side antenna from the LCD module as shown.