Acer Aspire 5737z Service Guide

Chapter 391
LCD Module Reassembly Procedure
Replacing the MIC and Antennas
1.Place the Microphone Module in the LCD Module 
as shown.2.Run the cable as shown and secure it using the 
adhesive tabs.
3.Replace the left and right antennas as shown. Ensure that the locating pin on each antenna is correctly 
seated. Press down on the adhesive pads (green callout) to secure the antennas in place.
4.Replace the left antenna cable (white) as shown. 
Ensure that the cable is inserted along the cable 
channel and...

92Chapter 3
6.Replace the right antenna cables (black and gray) 
as shown. Ensure that the cables are inserted 
along the cable channel and secured under each 
adhesive tab strip.7.Ensure the antenna and MIC cables pass through 
the hinge well as shown to avoid trapping.
NOTE: The LCD Module appears as shown when the MIC and Antennas are replaced correctly. 

Chapter 393
Replacing the LCD Panel
1.Insert the LCD Panel cable into the LCD Panel 
connector as shown.2.Replace the adhesive strip securing the connector 
in place.
3.Align the LCD brackets with the screw holes on the panel. Starting with the top most screws (marked with  U) 
replace the eight screws (four on each side) in the brackets as shown.
4.Place the LCD Panel in the back cover. 
IMPORTANT: Ensure that the LCD power cable passes 
through the hinge well and is not trapped under the...

94Chapter 3
Replacing the Camera
Replacing the Inverter
1.Place the camera in the LCD Module.2.Connect the cable to the camera module.
1.Place the Inverter in the LCD Module as shown.2. Connect the left side inverter cable.
3. Connect the right side inverter cable.
NOTE: Lift the Inverter slightly to connect the cable if 
necessary.4.Replace the single securing screw. 

Chapter 395
Replacing the LCD Bezel
1.Locate the bezel bottom edge first and press down the edges until there are no gaps between the bezel and 
the LCD Module.
IMPORTANT: Ensure that the LCD cables pass through the hinge wells and are not trapped by the bezel.
2.Replace the four screws and the rubber screw caps provided. 

96Chapter 3
Main Module Reassembly Procedure
Replacing the CPU
IMPORTANT:The CPU has a Pin1 locator that must be positioned corresponding to the marker on the CPU 
socket.
1.Carefully turn the mainboard upside down (CPU side up), and place the CPU into the CPU socket as 
shown, taking note of the Pin1 locator.
2.Gently close the socket lever and snap it into place in the securing clip.
Socket
Pin1 LocatorCPU
Pin1 Locator 

Chapter 397
Replacing the Thermal Module
IMPORTANT:Apply a suitable thermal grease and ensure all heat pads are in place before replacing the 
Thermal Module.
The following thermal grease types are approved for use:
•Silmore GP50
•Honeywell PCM45F-SP
•ShinEtsu 7762
The following thermal pads are approved for use:
• Eapus XR-PE
1.Remove all traces of thermal grease from the CPU using a lint-free cloth or cotton swab and Isopropyl 
Alcohol, Acetone, or other approved cleaning agent. 
2.Apply a small amount...

98Chapter 3
Replacing the Mainboard
Replacing the Bluetooth Module
1.Connect the Bluetooth cable to the Mainboard.
2.Turn the Mainboard over and place it in the 
chassis, left side first to insert the I/O ports 
correctly. 3.Rotate the Mainboard downward into position.
1.Place the Bluetooth Module in the Mainboard bay.2.Connect the Bluetooth cable to the module as 
shown. 

Chapter 399
Replacing the USB Board
1.Place the USB Board in the Mainboard bay.2.Replace the single securing screw as shown.
3.Connect the USB cable to the Mainboard.4.Ensure that the USB cable runs along the cable 
channel as shown.
5.Connect the USB cable to the USB Board. 

100Chapter 3
Replacing the Right Speaker Module
Replacing the Left Speaker Module
1.Place the Right Speaker Module in the chassis as 
shown.2.Replace the single securing screw.
3.Run the cable as shown along the chassis and on to the Mainboard.
1.Place the Left Speaker Module in the Upper Cover 
as shown.2.Replace the adhesive strip to hold the cable in 
place.