Acer Aspire 2930 Service Guide
Have a look at the manual Acer Aspire 2930 Service Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 720 Acer manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
62Chapter 3 Removing the Antenna 1.Remove the Memory Cover. See “Removing the Lower Covers” on page 47. 2.Remove the WLAN Module. See “Removing the WLAN Module” on page 48. 3.Remove the Keyboard. See “Removing the Keyboard” on page 59. 4.Peel back the cover to expose the Antenna cables. 5.Pull the cables completely through the housing. 6.Tilt the computer on its side and feed the cables through to remove from the housing.
Chapter 363 7.Place the computer rightside up, and remove the cables from the housing.
64Chapter 3 Removing the LED Board 1.Remove the Keyboard. See “Removing the Keyboard” on page 59. 2.Unlock the FFC connector and remove the FFC. 3.Remove the single securing screw. 4.Grasp the top side of the LED Board and pivot upwards to remove. StepSizeQuantityScrew Type LED Board M2*3 1
Chapter 365 Removing the Power Board 1.Remove the Keyboard. See “Removing the Keyboard” on page 59. 2.Unlock the FFC connector and remove the FFC. 3.Remove the single securing screw. 4.Using your finger lift the bottom side of the Power Board to remove. StepSizeQuantityScrew Type Power Board M2*3 1
66Chapter 3 Removing the LCD Module 1.Remove the Antenna cables. See “Removing the Antenna” on page 62. 2.Remove the LED Board. See “Removing the LED Board” on page 64. 3.Remove the Power Board. See “Removing the Power Board” on page 65. 4.Remove the two securing screws from the bottom of the chassis. 5.Turn the computer over and remove the four securing screws (two on each side) from the LCD module. 6.Remove the Ground screw and Ground cable. StepSizeQuantityScrew Type LCD Module M2.5*5 2 StepSizeQuantityScrew Type LCD Module (red callout)M2.5*4 4 Ground Screw (blue callout)M2*3 1 Ground Cable Ground Screw
Chapter 367 7.Disconnect the Ground cable as shown. 8.Disconnect the two cables as shown. NOTE: The Power Board must be removed to expose the LCD cables. 9.Grip the LCD and carefully remove the module from the chassis. IMPORTANT:Place the LCD module face up on a clean surface to prevent scratching or damage.
68Chapter 3 Removing the Upper Cover 1.Remove the ExpressCard dummy card. See “Removing the ExpressCard dummy card” on page 45. 2.Remove the Switch Board. See “Removing the LED Board” on page 64. 3.Remove the LCD module. See “Removing the LCD Module” on page 66. 4.Turn the computer over. Remove the eight (8) screws on the bottom panel. 5.Turn the computer over. Remove the five screws on the top panel. StepSizeQuantityScrew Type Upper Cover (blue Call out)M2.5*5 1 Upper Cover (red Call out)M2.5*8 7 StepSizeQuantityScrew Type Upper Cover M2.5*5 5
Chapter 369 6.Disconnect the four cables from the mainboard as shown. Release the securing latch and disconnect (A) as shown.Release the securing latch and disconnect (B) as shown. Release the securing latch and disconnect (C) as shown.Release the securing latch and disconnect (D) as shown.A B C D
70Chapter 3 IMPORTANT:Do not lift the entire Upper Case up at the same time or damage may occur. 7.Grasp the top right corner of the Upper Case and pivot upwards. 8.Continue prying the right upwards until the right side is at a 45 degree angle. 9.Slide the Upper Case off the lower base.