3M Multimedia Projector H10 Operators Manual

							41
WARNING• Please carefully read the “Product Safety Guide”.
Never use the projector if abnormal operations such as smoke, strange od\
or, excessive
sound, damaged casing or elements or cables, penetration of liquids or f\
oreign matter,
etc. should occur.
Phenomena That May Easily Be Mistaken For Machine Defects
• Although bright spots or dark spots may appear on the screen, this \
is a
unique characteristic of liquid crystal displays, and such do not consti\
tute or imply a machine defect.NOTE
Before requesting repair, please check in accordance with the following \
chart. If the
situation cannot be corrected, then contact your dealer.
PhenomenonCases not involving a machine defect,  and Items to be confirmedReferencepages
Power does not
come ON.
The main power source is not ON. 
Turn on the main power.
11,14The electrical power cord is not plugged in. 
Correctly connect the power cord.
The main power source has been interrupted during operation,
such as by a power outage (blackout), etc.
Be sure to press the  “Ó ” (power OFF) side of the main power switch,
and leave this OFF for at least 20 minutes. After the unit has
sufficiently cooled down, turn ON the power source.
14
Neither sounds
nor pictures are
outputted.The input changeover settings are mismatched.
Select the input signal, and correct the settings.15
No signal is being inputted.
Correctly connect the connection cables.10
Pictures are
displayed, 
but no sounds
are heard.
The electrical wiring to this unit is not correctly connected.
Correctly connect the connection cables.10
The volume setting has been set at (or adjusted to) an
extremely low level.
Adjust the VOLUME setting to a higher level.17
The MUTE mode is the current setting.
Press the MUTE button to release (change) the MUTE mode setting.17
Sounds are
heard, 
but no pictures
are displayed.
The electrical wiring to this unit is not correctly connected.
Correctly connect the connection cables.10
The brightness setting has been set at (or adjusted to) an
extremely low level.
Adjust the BRIGHT setting to a brighter level.23
The lens cap has not been removed.
Remove the lens cap.4,14
Colors have a
faded- out
appearance, or
Color tone is
poor.Color settings are not correctly adjusted.
Perform picture adjustments by changing the COLOR BAL R,
COLOR BAL G, COLOR BAL B, COLOR, and/or the TINT settings,
etc.
24
Troubleshooting (continued)
4&O
 
 
 
 1.
 
 
						

							42
PhenomenonCases not involving a machine defect, and Items to be confirmedReferencepages
Pictures appear
dark.
The brightness setting and/or contrast setting has not been
properly adjusted.
Perform picture adjustments by changing the BRIGHT and/or
CONTRAST settings, etc.
23
The WHISPER mode is the current setting.  
Change (by releasing) from the WHISPER mode.
Lamp is approaching the end of its product lifetime.
Exchange the old lamp with a new lamp.32,33
Pictures appear
blurry.
Either the FOCUS setting or the H PHASE is not properly
adjusted.
Adjust the focus and the H PHASE setting.
15,26
The lens is dirty or misty.
Clean the lens.36
Phenomena That May Easily Be Mistaken For Machine Defects (continued)
Troubleshooting (continued)
4&O
 
 
 
 1.
 
 
						

							43
• This specifications are subject to change without notice.NOTE
ItemSpecification
Product nameLiquid crystal projector
Liquid
crystal
panelPanel size1.4 cm (0.55 type)
Drive systemTFT active matrix
Pixels409,920 pixels (854 horizontal x 480 vertical)
LensZoom lens F=1.6 ~ 1.8  f=16.8 ~ 20.1 mm
Lamp130W UHB
Speaker1.0W
Power supplyAC100 ~ 120V, 2.4A / AC220 ~ 240V, 1.1A
Power consumption220W
Temperature range0 ~ 35°C (Operating)
Size329 (W) x 107 (H) x 245 (D) mm (Not including protruding parts)
Weight (mass)3.1 kg (6.8 lbs.)
Ports
RGB Input Ports
RGB ................................1
VIDEO Input Ports
VIDEO ............................1
S-VIDEO ........................1
COMPONENT VIDEO
(C
R/PR, CB/PB, Y) ............1AUDIO Ports
AUDIO ............................1
AUDIO R, L. ....................1
CONTROL Ports
CONTROL ....................1
121
50
71
329
245
86
107
Specifications
4&O
 
 
 
 1.
 
 
						

							44Accessories 
œœ
œœœœœœœœœœœœœœœœœœœœœœœœœœœœœœœœœœœœœœœœ 
Part Number
UHB lamp, 130W œœœœœœœœœœœœœœœœœœœœœœ 78-6969-9693-9
Air Filter œœœœœœœœœœœœœœœœœœœœœœœœœœ 78-8118-9177-5
Power cord (US) œœœœœœœœœœœœœœœœœœœœœœœ 78-8118-9178-3
Power cord (UK) œœœœœœœœœœœœœœœœœœœœœœœ 78-8118-9179-1
Power cord (Europe) œœœœœœœœœœœœœœœœœœœœœ 78-8118-9180-9
VGA cable œœœœœœœœœœœœœœœœœœœœœœœœœ 78-8118-8708-8
RCA component cableœœœœœœœœœœœœœœœœœœœœ78-8118-8843-3
Remote control œœœœœœœœœœœœœœœœœœœœœœœ78-8118-9181-7
Soft caseœœœœœœœœœœœœœœœœœœœœœœœœœœ78-8118-9194-0
Baseœœœœœœœœœœœœœœœœœœœœœœœœœœœœ78-8118-9191-6
Not Included with Basic Packet œœœœœœœœœœœœœœœœœœœœœœœœœœ  Part Number
Ceiling mountœœœœœœœœœœœœœœœœœœœœœœœœ78-6969-9694-7
Adjustable height suspensionœœœœœœœœœœœœœœœœœ78-6969-9698-8
Shipping caseœœœœœœœœœœœœœœœœœœœœœœœœ78-6969-9717-6
S-Video cableœœœœœœœœœœœœœœœœœœœœœœœœ78-8118-3238-1
RS-232C control cableœœœœœœœœœœœœœœœœœœœœ78-8118-9192-4
Mac adapter œœœœœœœœœœœœœœœœœœœœœœœœ78-8118-3308-2
Soft rolling luggage caseœœœœœœœœœœœœœœœœœœœ78-6969-9716-8
Soft side case with shoulder strapœœœœœœœœœœœœœœœ78-6969-9715-0
Ultra value warranty H10 (US only)œœœœœœœœœœœœœœœ78-6969-9700-2
Deluxe Mouse Emulation Kit œœœœœœœœœœœœœœœœœ78-6969-9233-4
How to Order
Please order these parts through your dealer, or contact 3M Customer Ser\
vice at the
following number :
In U.S. or Canada : 1-800-328-1371
In other locations,contact your local 3M sales office.
RCA Video/Audio cableœœœœœœœœœœœœœœœœœœœœ78-8118-3234-0
Accessories
4&O
 
 
 
 1.
 
 
						

							3M Austin Center
Building A145-5N-01
6801 River Place Blvd.
Austin, TX 78726-90003M Canada
P.O. Box 5757
London, Ontario
N6A 4T13M Mexico, S.A. de C.V.
Apartado Postal 14-139
Mexico, D.F.  07000
Mexico 3M Europe
Boulevard de lOise
95006 Cerge Pontoise Cedex
France
Litho in Japan
© 3M 2004
78-6970-9379-3 Rev. A
Let us help you make the most of your next presentation.  We offer every\
thing from presentation supplies to tips for better mee tings.  And were the only
transparency manufacturer that offers a recycling program for your used \
transparencies.  For late-breaking news, handy referenc e  and free product samples, call
us toll-free in the continental United States and Canada, 24 hours a day\
, or visit our Internet Website.
DN00671 (H10_OG_ENG)
Intended Use
Before operating this machine, please read this entire manual thoroughly\
. The 3MTM Multimedia Projectors are designed, built, a nd tested for use indoors, 
using 3M lamps, 3M ceiling mount hardware, and nominal local voltages.
The use of other replacement lamps, outdoor operation, or different volt\
ages has not been tested and could damage the projector  peripheral equipment 
and/or create a potentially unsafe operating condition.
3M Multimedia projectors and Wall Display Systems are designed to operat\
e in a normal office environment.
    16 to 29C (60 to 85 F)
    10- 80 %RH (without condensation)
     0- 1828 m (0-6000 feet) above sea level
The ambient operating environment should be free of airborne smoke, grea\
se, oil and other contaminates that can affect the oper ation or performance of the
projector. 
Use of this product in adverse conditions will void the product warranty\
.