3M Multimedia Projector H10 Operators Manual

							21
Signal Searching
Selecting The Aspect Ratio
1Press the SEARCH button.Cycle through input signals, displaying the images of retrieved signals.\
 If
no signal is found, returns to the signal that was selected before the s\
earch
was begun.
• May not function properly with some input signals.
• The signal searching function takes about 10 seconds to display an image\
.NOTE
• The temporarily blanking function will automatically finish if eith\
er the STANDBY/ON, SEARCH,
RGB, VIDEO, FREEZE, AUTO, VOLUME, MUTE, POSITION or MENU button of remot\
e control is pressed, or if a button of projector is pressed, or if there is a change in the input s\
ignal’s state.NOTE
rgb                  video                 s-video
component video
VIDEO
ASPECT
MUTE
KEYSTONE
FREEZE
VOLUME
STANBY/ON
MAGNIFY
AUTO BLANK
RGB SEARCH
OFF ON
VIDEO
ASPECT
MUTE
KEYSTONE
FREEZE
MENU
POSITION
ENTER
ESC RESET
VOLUME
STANBY/ON
MAGNIFY
AUTO BLANK
RGB SEARCH
OFF ON
VIDEO
ASPECT
VOLUME
STANBY/ON
MAGNIFY
AUTO BLANK
RGB SEARCH
ON
SEARCH
1
 • At a RGB input, selecting an aspect ratio may display the message
“SYNC IS OUT OF RANGE”. In this case, please select one of other
aspect ratios.
ASPECTRGB input
VIDEO, S-VIDEO, COMPONENT VIDEO input
Press the ASPECT button.
4:3            16:9            15:9             32:15
4:3                  16:9                  WIDE         
Temporarily Blanking The Screen
1Press the BLANK button.The input signal screen is shut off, and a blank screen appears. You can\
set the blank screen using the menu (from the SCREEN menu,
select BLANK). 
Press the BLANK button again to remove the blank screen,
and return to the input signal screen.
BLANK
Operating (continued)
4&O



1.

Ö”´

• At a COMPONENT VIDEO input of 16:9 Hi-Vision of 1125i /750p, only 16:9 can be selected.
MOVIE-2         MOVIE-1 
						

							22
This projector has the following menus: MAIN, PICTURE-1, PICTURE-2, INPU\
T, AUTO,
SCREEN, OPTION. Each of these menus is operated using the same methods. \
The basic
operations of these menus are as follows.
1Press the MENU
button.
The menu display
appears on the screen.
2Use the /
buttons to select
a menu , then
press the or
ENTER button.
The display of the
selected menu
appears.
3Use the  /
buttons to select an item,
then press the or ENTER button.
The operation display of the selected item appears. 
4Use the  /
buttons to operate the item.
When you want to reset the adjustment, press the RESET
button during the operation. Note that the items whose
functions are performed simultaneously with operating (ex.
LANGUAGE, WHISPER, H PHASE etc.) are not reset.
When you want to return to the previous display, press the
or ESC button.
[ex. Adjusting
VOLUME]
1. Press the MENUbutton.
2.
Use the /
buttons to select
the OPTION, then
press the or
ENTER button.
3.Use the / buttons to select
the VOLUME,
then press the or ENTER
button.
4.Use the / buttons to adjust
the VOLUME.
5.Press the MENU button.
5Press the MENU button, or do not perform
any operation for several seconds
.
The menu display disappears and your operation finishes.
MENU
RESETESC
ENTER
VIDEO
ASPECT
MUTE
KEYSTONE
FREEZE
MENU
POSITION
ENTER
ESC RESET
VOLUME
STANBY/ON
MAGNIFY
AUTO BLANK
RGB SEARCH
OFF ON
Using The Menu Functions
Multifunctional Settings
4&O
 
 
 
 1.
 
 
						

							23
MAIN Menu
With the MAIN menu, the items shown in the table below can be
performed.
Perform each operation in accordance with the instructions in the
table below.
MENUMAIN
PICTURE-1
PICTURE-2
INPUT
AUTO
SCREEN
OPTION KEYSTONE
BRIGHT
CONTRAST
ASPECT
WHISPER
MIRROR
LANGUAGE
[Language] +0
+0
+0
4:3
NORMAL
NORMAL
ENGLISH
: SELECT
ItemDescription
KEYSTONE
Adjust Brightness:
Light ñDark
Adjust the Keystone (Vertical) Distortion:
Upper in the data  ñLower in the data
• The adjustable range of this function will vary with the type of input s\
ignal. At some signals, this function may not work well.
• When the V:INVERT or the H&V:INVERT is selected under the MIRROR item, i\
f the projector screen is inclined or if the projector is angled downward,\
 this
function may not work correctly.
• When the WIDE is selected under the ASPECT item of the MAIN menu, this adjustment is ignored.
• When the zoom adjustment is set to the TELE side, this correction may be\
 excessive. This function should be used with zoom set to WIDE whenever
possible.
BRIGHT Adjust Brightness: Light ñDark
MOVIE-1 ñ  MOVIE-2
CONTRASTAdjust Contrast:Strong ñWeak
ASPECT
Select an Aspect Ratio 
At a RGB input:
4:3  ñ16:9  ñ15:9  ñ32:15
• At a RGB input, selecting an aspect ratio may display the message “SY\
NC IS OUT OF RANGE”. In this case, please select one of other aspect ratios\
.
At a VIDEO input, a S-VIDEO input or a COMPONENT VIDEO input: 4:3  ñ 16:9  ñ WIDE  ñ 
• At a COMPONENT VIDEO input of 16:9 Hi-Vision of 1125i/750p, only 16:9 ca\
n  be selected.
WHISPER
Select the Whisper Mode:NORMAL  ñWHISPER
• When the WHISPER is selected, acoustic noise and screen brightness are reduced.
MIRRORSelect a Mirror Status: NORMAL  ñH:INVERT  ñV:INVERT  ñH&V:INVERT
LANGUAGE
Select a Menu Language:ENGLISH  ñFRANÇAIS  ñDEUTSCH  ñESPAÑOL 
ð ITALIANO  ñNORSK  ñNEDERLANDS 
ð ÔŠ  ñ PORTUGUÊS ñ
¤ñ
ð SVENSKA  ññ SUOMI ñPOLSKI
RESET
Reset the MAIN Menu Items:
Selecting the EXECUTE performs this function.
EXECUTE CANCEL
• The items of the MAIN menu are collectively returned to the initial sett\
ing. Note that the items WHISPER and LANGUAGE are not reset.
ð
ð ð
ð
4&O
 
 
 
 1.
 
 
						

							24
PICTURE - 1 Menu
With the PICTURE - 1 menu, the items shown in the Table below can be
performed.
Perform each operation in accordance with the instructions in the table \
below.
MENUMAIN
PICTURE-1
PICTURE-2
INPUT
AUTO
SCREEN
OPTION GAMMA
COLOR BAL R
COLOR BAL G
COLOR BAL B
SHARPNESS
COLOR
TINT
MY MEMORY  NORMAL
+0
+0
+0
+0
+0
+0
SAVE1
: SELECT
ItemDescription
GAMMASelect a Gamma Mode:
NORMAL
ñCINEMA ñDYNAMIC ñCUSTOM• Selecting the COSTOM and then pressing the  or the ENTER button calls
the CUSTOM menu.
CUSTOM 
MenuSelecting one from the following and then pressing the  or the ENTER
button performs each function.
GAMMA ñCOLOR TEMP ñRñ Gñ B• The R, G and B can be selected only when the USER is selected under the
COLOR TEMP.
COLOR BAL R Adjust the Red Color Balance: Strong  ñWeak
COLOR BAL GAdjust the Green Color Balance: Strong  ñWeak
COLOR BAL BAdjust the Blue Color Balance: Strong ñWeak
SHARPNESSAdjust the Whole Sharpness: Clear ñSoft
• This is a function for video inputs. This item can’t be selected only\
 at RGB inputs.
COLOR
Adjust COLOR : Strong ñWeak 
• This is a function for video inputs. This item can’t be selected only\
 at  RGB inputs including SCART RGB inputs.
• It is unavailable to deepen colors on SECAM signal input. (The adjustme\
nt bar position and value in menu box are changeable but no effect.)
TINTAdjust the Tint: Green ñRed
•  This is a function for video inputs. This item can’t be selected only\
 at  RGB inputs including SCART RGB inputs.
Multifunctional Settings (continued)
GAMMAAdjust the Gamma Data:
Up ñDown
COLOR TEMP
Select a Color Temperature Mode:
HIGH ñMIDDLE ñLOW ñUSER
R
Adjust the Red Color Level for the USER mode of the
COLOR TEMP:
Strong ñWeak
G
Adjust the Green Color Level for the USER mode of the
COLOR TEMP:
Strong ñWeak
B Adjust the Blue Color Level for the USER mode of the
COLOR TEMP:
Strong ñWeak
CUSTOM
CUSTOM
CUSTOM
CUSTOM
CUSTOM
4&O
 
 
 
 1.
 
 
						

							25
ItemDescription
MY MEMORY
Load/Save a Setting:
Selecting one from the following and then pressing the or the ENTER
button performs each function.
LOAD1ñLOAD2 ñLOAD3 ñLOAD4
ð SAVE1 ñSAVE2 ñSAVE3 ñSAVE4
• This projector has 4 memories called M1, M2, M3 and M4 for settings.
Performing the SAVE1, SAVE2, SAVE3 or SAVE4 puts the current setting dat\
a
on the memory whose number corresponds. Performing the LOAD1, LOAD2,
LOAD3 or LOAD4 calls the data of memory whose number corresponds, and
adjusts the picture automatically depending on the data. 
• The LOAD1, LOAD2, LOAD3 or LOAD4 cannot be selected when there is no memory whose number corresponds.
• At a different signal input from the signal that was being inputted when\
 the setting was memorized, the picture may not be adjusted correctly.
RESET
Reset the PICTURE-1 Menu Items:
Selecting the EXECUTE performs this function.
EXECUTE CANCEL
• The items of the PICTURE-1 menu are collectively returned to the initial\
 setting. Note that the items MY MEMORY and CUSTOM - GAMMA are not
reset.
PICTURE - 1 Menu (continued)
Multifunctional Settings (continued)
ð ð
4&O
 
 
 
 1.
 
 
						

							26
PICTURE - 2 Menu
With the PICTURE - 2 menu, the items shown in the table below
can be performed.
Perform each operation in accordance with the instructions in the
table below.
MENUMAIN
PICTURE-1
PICTURE-2
INPUT
AUTO
SCREEN
OPTION V POSITION
H POSITION
H PHASE
H SIZE
OVER SCAN
RESET
20
142
31
1344
95
: SELECT
ItemDescription
V POSITION Adjust the Vertical Position:
Up ñDown
• This item can be selected only at a RGB input.
H POSITIONAdjust the Horizontal Position: Left ñRight
• This item can be selected only at a RGB input.
H PHASE
Adjust the Horizontal Phase (to eliminate flicker) :
Right  ñLeft
• This item can be selected only at a RGB input or a COMPONENT VIDEO input.
H SIZE
Adjust the Horizontal Size: Large ñSmall
• When this adjustment is excessive, the picture may not be displayed correctly. In such a case, please press the RESET button during selectio\
n of
this item to reset the H SIZE.
• This item can be selected only at a RGB input.
OVER SCAN
Adjust the Over-scan Ratio: Large  ñSmall
• This item can be selected only at a VIDEO input, a S-VIDEO input or a COMPONENT VIDEO input.
• When this adjustment is too large, a certain degradation may appear at t\
he frame area of the picture. In such a case, please adjust small.
RESET
Reset the PICTURE-2 Menu Items:
Selecting the EXECUTE performs this function. EXECUTE CANCEL
• The items of the PICTURE-2 menu are collectively returned to the initial\
 setting. Note that the H PHASE item is not reset.
Multifunctional Settings (continued)
ð
4&O
 
 
 
 1.
 
 
						

							INPUT Menu
With the INPUT menu, the  items shown in the table below can be
performed. 
Perform each operation in accordance with the instructions in the
table below.
MENUMAIN
PICTURE-1
PICTURE-2
INPUT
AUTO
SCREEN
OPTION COLOR SPACE
COMPONENT
VIDEO
FRAME LOCK
3D-YCS
VIDEO NR
PROGRESSIVE
INFORMATION AUTO
COMPONENTAUTO
TURN ON
NORMAL
LOW
TURN OFF
: SELECT
27
ItemDescription
COLOR SPACE
Select a Color Space Mode:
AUTO 
ñRGB  ñSMPTE240  ñREC709  ñREC601
• This item can be selected only at a RGB input or a COMPONENT VIDEO
input. 
• When the AUTO is selected, the optimum mode is automatically selected. However, it may not work well at some signals. In such a case, select th\
e
SMPTE240 or REC709 for HDTV signal.
COMPONENT
Select a Function of COMPONENT VIDEO Jacks: COMPONENT  ñSCART RGB
• When the SCART RGB is selected, the  component videojacks function as
ports for a RGB input with a SCART cable. Refer to the section “Signa\
l
Connectors” of “TECHNICAL”.
VIDEO
Select a Signal Type Mode: AUTO  ñNTSC  ñPAL  ñSECAM 
ðNTSC 4.43  ñM-PAL  ñN-PAL
• This item performs only at a VIDEO input or a S-VIDEO input. For a COMPONENT VIDEO input, although this item is ineffective, the signal typ\
e is
identified automatically even if the AUTO is not selected.
• Selecting the AUTO automatically selects the optimum mode. However, it may not work well at a PAL60 signal and some other signals. If the pictu\
re
becomes unstable (ex. a irregular picture, color lack), please select \
the mode
depending on the input signal. 
• The AUTO operation requires approximately 10 seconds.
FRAME LOCK
Select the Frame Lock Mode: TURN ON  ñTURN OFF
• This function performs only at a RGB input with vertical frequency of 48\
 to 72 Hz.
• When the TURN ON is selected, a moving picture is displayed more smoothly.
• This function may cause a certain degradation of the picture. In such a \
case, please select the TURN OFF.
3D-YCS
Select a 3D-YCS mode: STILL IMAGE  ñNORMAL  ñTURN OFF
• This function performs only at a VIDEO input of NTSC 3.58.
• NORMAL is the mode for images with a lot of motions like movies, and STI\
LL IMAGE is the mode for images with few motions or completely still ones l\
ike
slides.
• When this function performs, the VIDEO NR function is ineffective.
Multifunctional Settings (continued)
ð
4&O
 
 
 
 1.
 
 
						

							28
ItemDescription
VIDEO NR
Select a Noise Reduction Mode:HIGH  ñMIDDLE  ñLOW
• This function performs only at a VIDEO input or a S-VIDEO input. At a VI\
DEO input of NTSC 3.58, this function performs only when the TURN OFF is
selected under the 3D-YCS.
• When the HIGH, the MIDDLE or the LOW is selected, the noise on screen is\
 reduced according to each mode.
• When this function is excessive, it may cause a certain degradation of t\
he picture. 
PROGRESSIVE
Select the Progressive Mode: TV  ñFILM  ñTURN OFF
• This function performs only at an interlaced signal of a VIDEO input, a \
S- VIDEO input or a COMPONENT VIDEO input of 525i or 625i signal. The FILM
mode is adaptable to the 3-2 Pull-Down system to the conversion.
• When the TV or FILM is selected, the screen image will be crisper. But i\
t may cause a certain defect (for example, jagged line) of the picture at a \
quick
moving object. In such a case, please select the TURN OFF, even though t\
he
screen image may lose the crisp.
• This function may cause a certain degradation of the picture. In such a \
case, please select the TURN OFF.
INFORMATION
Display the Information:
Pressing the  or the ENTER button performs this function.
• Use this function when you want the information about the current input \
(ex.the resolution and the vertical frequency at a RGB input, the signal typ\
e of a
video input) and setting states of the COMPONENT, the VIDEO and the
FLAME LOCK.
S2-ASPECT
Select the S2-ASPECT Mode: TURN ON  ñTURN OFF
• This function performs only at a S-VIDEO input.
• When the TURN ON is selected, an S2-Video signal can be identified and t\
he optimum aspect ratio is automatically selected. 
• When the ASPECT button of the remote control is used or the ASPECT item \
of the MAIN menu is operated, the S2-ASPECT mode will be switched to the
TURN OFF automatically.
RESET
Reset the INPUT Menu Items:
Selecting the EXECUTE performs this function. EXECUTE CANCEL
• The items of the INPUT menu are collectively returned to the initial set\
ting. Note that the INFORMATION item is not reset.
INPUT Menu (continued)
Multifunctional Settings (continued)
ð
4&O
 
 
 
 1.
 
 
						

							29
MENUMAIN
PICTURE-1
PICTURE-2
INPUT
AUTO
SCREEN
OPTION ADJUST
POWER OFF
SEARCH
RESET
0 min
TURN ON
: SELECT
AUTO Menu
With the AUTO menu, the items shown in the table below can be
performed. 
Perform each operation in accordance with the instructions in the
table below.
ItemDescription
ADJUST
Automatically Adjust the Picture:
Pressing the  or the ENTER button performs this function.
At a RGB input:
• V POSITION, H POSITION, H PHASE and HSIZE are automatically adjusted.
Please use this function with the maximum window size. 
At a VIDEO input or S-VIDEO input:
• This function performs only when the AUTO is selected under the VIDEO it\
em of the INPUT menu. For a COMPONENT VIDEO input, although this function i\
s
ineffective, the signal type is identified automatically even if the AUT\
O is not
selected.
• This function automatically selects the optimum mode for the input signa\
l. However, it may not work well at a PAL60 signal and some other signals. \
If
the picture becomes unstable (ex. irregular picture, color lack), plea\
se use
the function of VIDEO of the INPUT menu. 
• The operation of this function requires approximately 10 seconds. Also, please note that it may not function correctly with some input.
POWER OFF
Set the Automatically Power Off Timer: Long (Max. 99 minutes.)  ñShort (Min. 0 minute =DISABLE)
• This function performs only when the time is set to 1 to 99.
• When the set time passes without a valid signal (there is no signal, or\
 the signal is out of specifications), the projector lamp automatically goes\
 off, and
the POWER indicator begins blinking. Please refer to the section “Tur\
ning
OFF The Power” of “Power ON/OFF” about the turning off.
SEARCH
Automatically Signal Search: TURN ON  ñTURN OFF
• If the TURN ON is selected under this item when no signal input is detec\
ted, the projector begins searching for an input signal. When an input signal\
 is
detected the projector will cease searching and the picture will appear.\
• The priority of a search is as follows:  rgb 
à à video  à
à
s-video  à
à
component video
• If the projector is unstable to find an input signal at any of its ports\
, it will return to the state it was in prior to the search.
RESET
Reset the AUTO Menu Items:
Selecting the EXECUTE performs this function. EXECUTE CANCEL
• The items of the AUTO menu are collectively returned to the initial sett\
ing. Note that the item ADJUST is not reset.
ð
Multifunctional Settings (continued)
à
4&O
 
 
 
 1.
 
 
						

							30
SCREEN Menu
With the SCREEN menu, the items shown in the table below can be
performed.
Perform each operation in accordance with the instructions in the
table below.
: SELECT
MENUMAIN
PICTURE-1
PICTURE-2
INPUT
AUTO
SCREEN
OPTION BLANK
START UP
MENU POSITION
MESSAGE
RESET
BLACK
TURN ON
TURN ON
ItemDescription
BLANK
Select a Blank Screen Color:
BLUEñWHITEñBLACK
• The blank screen of selected color is displayed by pressing the BLANK button. Please refer to the section “Temporarily Blanking The Screen”\
 of
“Operating” about the screen blanking.
START UP
Select the Start Up Screen: TURN ONñTURN OFF
• If the TURN ON is selected when there is no signal or the detected signa\
l is out of specifications, the blank screen is displayed.
MENU POSITION
Adjust a Menu Position: 
Pressing the  or ENTER button start adjusting, Up
Left Right Down
• The  button does not finish this item. When you want to return to the
previous display, please press the ESC button.
MESSAGE
Select the Message Mode: TURN ONñTURN OFF
• When the TURN OFF is selected, the following message functions are disabled:The message of “AUTO IN PROGRESS”
The message of “NO INPUT IS DETECTED”
The message of “SYNC IS OUT OF RANGE”
The message while being searched for an input signal, “Searching …\
..”
The message when an input signal is detected, “Detecting …..”
The indication of the input signal by input change.
RESET
Reset the SCREEN Menu Items:
Selecting the EXECUTE performs this function. EXECUTE CANCEL
• The items of the SCREEN menu are collectively returned to the initial se\
tting. 
ð
Multifunctional Settings (continued)
4&O
 
 
 
 1.