3Com Router WL-602 User Manual

Wireless Settings69
Figure 51   Add WDS screen 
On the add WDS screen, enter the MAC address of the access point, up 
to 4 APs can be added to the AP MAC Address table, and click Apply. 
Here is an example of how to setup two units of 3Com Router over WDS. 
Note that when setting up two units of 3Com Router, you should disable 
the DHCP function on one of the units.
Setting of the first Router: 
■Set the LAN IP setting, make sure the DHCP function is enabled on this 
Router. 
■Set the wireless settings,...

70CHAPTER 5: CONFIGURING THE ROUTER
Figure 52   First Router add WDS Screen
Access the Web UI of the second Router, repeat the above steps to add 
the first Router to the WDS table (see Figure 53). 
Figure 53   Second Router add WDS Screen 

Wireless Settings71
AdvancedThe Advanced screen allows you to configure detailed settings for your 
wireless connection. Please note that you should not change this settings 
unless you are an expert user. There are six parameters that you can 
configure:
Figure 54   Wireless Advanced Setting Screen 
■Beacon Interval: this represents the amount of time between beacon 
transmissions. 
■DTIM Interval: A DTIM (Delivery Traffic Indication Message) is a 
countdown mechanism used to inform your wireless...

72CHAPTER 5: CONFIGURING THE ROUTER
network and will not be able to communicate with each other. You 
may want to utilize this feature if you have many guests that 
frequently connect to your wireless network. 

Internet Settings73
Internet SettingsYou can configure the settings for your WAN port connection.
WANThis feature is used to configure the parameters for your Internet 
connection. The information necessary to complete these screens should 
be obtained from your ISP. Check with your ISP first to find out what type 
of connection you should choose.
Figure 55   WAN Sc ree n
There are five options available for the connection mode:
■Dynamic IP — Using DHCP for WAN connection (see page 74)
■Static IP — Using...

74CHAPTER 5: CONFIGURING THE ROUTER
Dynamic IP
You can configure the Router to obtain an IP address automatically from a 
DHCP server.
Figure 56   Dynamic IP Screen
1Select Dynamic IP from the Internet sharing protocol drop-down menu.
2If the ISP requires you to input a Host Name, type it in the Host Name 
field.
3Click Apply.  

Internet Settings75
Static IP 
If your Service Provider has assigned a fixed IP address, enter the assigned 
IP address information on the screen.
Figure 57   Static IP Screen 
1Select Static IP from the Internet sharing protocol drop-down menu.
2Enter your IP address in the IP address assigned by your service provider 
field.
3Enter the subnet mask in the Subnet Mask field.
4Enter the default gateway IP address in the Service Provider Gateway 
Address field.
5Enter DNS IP address. 
6If there is a...

76CHAPTER 5: CONFIGURING THE ROUTER
PPPoE
PPP over Ethernet, provides routing for multiple PCs, this mode is often 
used for the DSL connection. To configure this function correctly, you 
should obtain the information from your ISP. 
Figure 58   PPPoE Settings Screen
1Select PPPoE from the Internet sharing protocol drop-down menu.
2Enter the user name assigned to you by your ISP in the Username field. 
And enter the password assigned to you by your ISP in the Password field. 
Re-enter your password in...

Internet Settings77
PPTP
If your ISP uses PPTP as the Internet connection protocol, setup the details 
on this screen.
Figure 59   PPTP Screen
1Select PPTP from the Internet sharing protocol drop-down menu.
2Enter the PPTP Server information. 
3Enter the user ID in the User ID field. And enter the password assigned to 
you by your ISP in the Password field. Re-enter your password in the 
Retype Password field.
4If you want your Router to automatically disconnect from the Internet 
after a period of...

78CHAPTER 5: CONFIGURING THE ROUTER
L2TP
If your ISP uses L2TP as the Internet connection protocol, setup the details 
on this screen. This options is mostly used in Israel.
Figure 60   L2TP Connection Screen
1Select L2TP from the Internet sharing protocol drop-down menu.
2Enter the L2TP Server information.
3Enter the User ID and Password required by your ISP.
4Retype the password. 
5Enter the maximum Idle Timeout for the Internet connection. After this 
time has been exceeded the connection will be...