Zenith Projector Dxg 210 User Manual

TheaterLite™
DXG-210operating guide 

3
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert...

5
4
(Continued from previous page)
14. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the
product, be sure the antenna or cable system is grounded
so as to provide some protection against voltage surges and
built-up static charges. Article 810 of the National
Electrical Code (U.S.A.), ANSI/ NFPA 70 provides informa-
tion with regard to proper grounding of the mast and sup-
porting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding...

Page
Using the menus
 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
6.1 The Menu System  . . . . . . . . . . . . . . . . . . . . . . . . . .15
6.1.1 Main menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
6.2 Set-up Menu  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
6.2.1 Picture orientation  . . . . . . . . . . . . . . . . . . . . . . . . . .17
6.2.2 Language  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
6.2.3 Quick...

1.3 Insert batteries in the
remote control Figure 5 shows the remote control with the
battery lid removed. Slide off the battery lid
and insert the batteries with the + and - poles
correct. Slide the battery lid back on again.1.4 Connect projector to
power supply Plug in your projector. Do not plug it into a
switched outlet. Your Zenith projector is
designed to operate on standard current, 
120-volt, 60 Hertz AC. Do not attempt to
operate it on DC current.The registration card or copy of invoice is your...

The procedure for connecting
a video source to the projec-
tor is the same for S-Video
and Composite video.SECAM, PAL N and PAL M modes are manually
selected by pressing the “Green Button“. If the
right format is not found the first time, press
again. The video format is stored separately
for each connector.
1.Make sure that the video source 
and the projector are switched off. 2.Connect the video cable from the Video
out connector of the video source to the
correct video connector on the projector
plug...

The Remote control is very easy to operate. It
has only six keys in addition to the pressure
sensing mouse pad. 
The six keys are:Key underneath the controlLeft mouse keySmall gray keyInterrupt/break an action (right mouse key)MenuThe menu key gives access to the menu control
functions. To move within the various menu
functions, position the arrow cursor by pressing
the sensitive mouse pad and click with the left
mouse button which is located underneath the
remote control.
If you are in menu mode and...

5.4  Adjusting the height and
angle of the projectorYou can adjust the height and angle of the
projector by adjusting the four small feet
underneath the product. Note!
The projector should never be left with an
angle of more than 15 degrees over a long
period of time. Doing so will shorten the
lifetime of the lamp.5.5  Aspect Ratio Selection Aspect Ratio selection.In this menu you can select the aspect
ratio of 4:3 or 16:9.6.1 The menu systemMain menu. Menu with video input.
6.1.1 Main menuThe main menu...

17
16
17
6.2 Set-up menuSet-up menuIn the set-up menu the following 
sub-menus are available:•
Picture orientation
•
Language
•
Quick key assignment
•
ZAP keys assignment
•
Accumulated lamptime
6.2.1 Picture orientation Picture orientationThe picture orientation menu is used for
rotating and mirroring the picture.NormalNormal is used when the projector is standing
on a table projecting a picture on a screen.MirrorMirror is used when the projector is projecting
a picture from behind the screenRotateRotate...

19
18
19
6.2.4 Zap menuZap menuThe Zap menu is used to assign functions to
the zap keys on the remote control. The menu
consists of two columns of buttons where the
left column assigns the functions to the left
key and the right column assigns the functions
to the right key.
Note:
Un-selecting all boxes for Zap 1 assigns the
“Zap 1’ button on the remote to Power-up
the projector from stand-by mode.
Un-selecting all boxes for Zap 2 assigns the
“Zap 2” button on the remote to function
as the Power-down...