Zanussi Zwq 6100 User Manual
Have a look at the manual Zanussi Zwq 6100 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 276 Zanussi manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
ENUser manual 2 FRNotice d'utilisation 14 Lave-linge ZWQ 6100 ZWQ 6120
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 Product description _ _ _ _ _ _ _ _ _ _ _ _ _ 3 Personalisation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4 How to run a wash cycle? _ _ _ _ _ _ _ _ _ _ 5 Daily Use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5 Programmes table _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7 Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ 8Operating Problems _ _ _ _ _ _ _ _ _ _ _ _ _ 9 Detergents and Additives _ _ _ _ _ _ _ _ _ _ 10 Technical Specifications _ _ _ _ _ _ _ _ _ _ 10 Consumption values _ _ _ _ _ _ _ _ _ _ _ _ 11 Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11 Environment _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 13 Subject to change without notice. Safety information Please read these points carefully before instal- ling and using your appliance. Keep this user manual with your appliance. General safety • Do not modify or attempt to modify this appli- ance. This would put yourself in danger. • Ensure that all coins, safety pins, brooches, screws etc have been removed before start- ing a washing programme. If left in washing, they can seriously damage the appliance. • Use the recommended quantity of detergent. • Put small items together (socks, belts etc.) in a small linen bag or pillow case. • Unplug and close inlet hose tap after using appliance. • Always disconnect the power supply from the appliance before cleaning or mainte- nance. • Do not machine wash clothes with ribbing, unfinished or torn material. Installation • Unpack or ask for the appliance to be un- packed immediately upon delivery. Check the outside of the appliance is not damaged in any way. Report all transit damage to your re- tailer. • Remove all transit bolts and packaging be- fore installing the appliance. • Connection to the water supply must be car- ried out by a qualified plumber. • If your domestic electrical circuit needs adapting to allow the appliance to be plug- ged in, use a qualified electrician.• Ensure that, after installation, the power ca- ble is not trapped under the appliance. • If the appliance is installed on carpeted floor, ensure that the carpet does not obstruct any ventilation ducts located at the base of the appliance. • The appliance must be equipped with an earthed power plug which conforms to regu- lations. • Before connecting your appliance to the power supply, carefully read the instructions in the chapter entitled “Electrical connec- tion”. • Replacing the power cable should only be carried out by an authorised service engi- neer. • The manufacturer cannot be held responsible for any damage resulting from incorrect in- stallation. Precautions to be taken against frost If your appliance is exposed to temperatures below 0°C, the following precautions must be taken: • Close the tap and disconnect the inlet hose. • Place the end of this hose and the drain hose in a basin on the floor. • Select the Drain programme let it run until the end of the cycle. • Disconnect the appliance from the power supply by turning the programme selector to “Stop” . • Unplug the appliance. • Replace the inlet hose and drain hose. 2 www.zanussi.com
This way, the water remaining in the hoses will be drained away, avoiding any ice formation which would damage your appliance. Before turning your appliance on again, ensure that it is installed in an area where the tempera- ture will not fall below freezing. Use • Your appliance is intended for normal do- mestic use. Do not use the appliance for commercial or industrial purposes or for any other purpose. • Refer to the instructions on the label of each item before washing. • Do not put items into the washing machine which have had stains removed with petrol,alcohol, trichlorethylen etc. If such stain re- movers have been used, wait until the prod- uct has evaporated before putting these items into the drum. • Empty pockets and unfold items. • This appliance is not intended for use by per- sons (including children) with reduced physi- cal, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction con- cerning use of the appliance by a person re- sponsible for their safety. Children should be supervised to ensure that they do not play with the appliance. Product description 1 3 2 1. The control panel 2. Lid handle 3. Adjustable levelling feet 3 www.zanussi.com
The control panel 123456 1. Programme selector 2. Buttons and their functions 3. Display4. "Door locked" light 5. "Start/Pause" button 6. "Delay start" button Dispenser box Prewash Wash Softener (do not fill above the MAX symbol M ) Personalisation Child safety This option provides two types of locking : • if the option is activated after the cycle has started, no changes to the options or pro- gramme is possible. The cycle runs and you must deactivate the option to run a new cycle. • if the option is activated before the cycle has started, the appliance cannot be started.To activate child safety, turn appliance on and press “Spin” and “Option” simultane- ously until the confirmation symbol shows on in the display. The appliance memorises the se- lection of this option. To deactivate child safety, repeat the process. 4 www.zanussi.com
How to run a wash cycle? Using for the first time • Ensure the electrical and water connec- tions comply with the installation in- structions.• Remove the polystyrene insert and all other items inside the drum. • Run an initial wash cycle at 90°C, with- out any washing but with detergent to clean the water tank. Daily Use Loading washing • Open the lid of the appliance. • Open the drum by depressing the locking button A: The two shutters unlock automati- cally. •Load the washing, close the drum and the lid of your washing machine. Warning! Before closing the lid of your appliance, ensure that the drum is properly closed : • When the two shutters are closed, • locking button A released. Proportioning of detergents Pour the amount of washing into the washing and prewash compartments if you have selected the “prewash” option. Pour fabric soft- ener into the compartment if necessary. Selection of desired programme Turn the programme selector to the required programme. The “Start/Pause” pushbutton flashes green. If you turn the programme selector to another programme while a cycle is in progress, the ap- pliance will ignore the new selected pro- gramme. “Err” flashes and the “Start/Pause” pushbutton flashes red for a few seconds. Selecting the spin speed Press the “Spin” button to change the spin speed. The maximum spin speeds are : A for Cottons, Jeans : 1200 rpm (ZWQ 6120), 1000 rpm (ZWQ 6100), for Handwash, Wool : 1000 rpm (ZWQ 6100), 900 rpm (ZWQ 6120), for Synthetics, Sport : 900 rpm, for Deli- cates, Curtains : 700 rpm. Rinse hold By selecting this function the water of the last rinse is not emptied out to prevent the fabrics from creasing. At the end of the programme, if you have selec- ted “Rinse hold” , you then need to select a “Spin” or “Drain” programme to finish the cycle and empty the water. Selecting options You must select the different options after se- lecting the programme and before pressing the “Start/Pause” pushbutton (see “Programme table”). Press the desired button(s) ; the corre- sponding lights come on. If pressed again, the lights go out. If one of the options is not com- patible with the selected programme, “Err” flashes on the display and the “Start/Pause” pushbutton flashes red. “Prewash” option The appliance runs a prewash at 30°C max. “Quick” option The washing time will be reduced depending on the programme selected. “Economy” option This option allows you to choose a lower tem- perature programme which is as effective as a higher temperature wash programme. 5 www.zanussi.com
“Easy iron” option If you select this option, the laundry is washed and spun delicately to prevent any creasing. This makes ironing easier. “Extra rinse” option The washing machine will add one or more rin- ses during the cycle. This option is recommen- ded for people with sensitive skin and in soft water areas. Temporary : Press the “Extra rinse” button. The option is only active for the selected pro- gramme. Permanent : Hold down the “Eco” and “Ex- tra rinse” buttons for a few seconds. The option is permanently activated, even if the ap- pliance is switched off. To deactivate it, repeat the process. “Delay start” This option allows you to delay the start of a wash programme by 30 minutes, 60 minutes, 90 minutes, 2 hours to 20 hours. The selected time appears on the display for a few seconds. You can change or cancel the delayed start time at any time before you press the “Start/ Pause” pushbutton, by pressing the “Delay start” pushbutton again ( ’ indicates im- mediate start). If you have already pressed the “Start/Pause” pushbutton and you want to change or can- cel the delayed start, proceed as follows : • To cancel the delayed start and start the cy- cle immediately, press “Start/Pause” and then “Delay start” . Press “Start/Pause” to start the cycle. • To change the timer delay period, you must go through the “Stop” position and re- programme your cycle. The lid will be locked during the delayed start time. If you need to open it, you must first pause the appliance by pressing the “Start/Pause” pushbutton. After closing the lid again, press the “Start/Pause” pushbutton. Start of the programme Press the “Start/Pause” pushbutton to start the cycle ; the corresponding light will come on green. The indicator lights up (lid locked). It is normal for the programme selector to remain stationary during the cycle. The remaining time appears on the display. If a delayed start has been selected, the countdown appears on the display. Interrupting a programme Adding washing during the first 10 mi- nutes When the light is off, you can add washing by proceeding as follows. Press the “Start/ Pause” pushbutton : the corresponding light will flash green while the appliance is paused. The lid can only be opened around 2 minutes after the washing machine has come to a stop. Press the “Start/Pause” pushbutton again to continue the programme. . Modifying the programme in progress Before making any changes to the current pro- gramme, you need to pause the washing ma- chine by pressing the “Start/Pause push- button. If the modification is not possible, “Err” flashes in the display and the “Start/Pause” pushbutton flashes red for a few seconds. If you still decide to change the programme, you must cancel the current programme (see be- low). . Cancelling the programme If you want to cancel the programme, turn the programme selector to the “Stop” position. End of the programme The washing machine stops automatically ; the “Start/Pause” pushbutton goes out and flashes on the display. The lid can only be opened around 2 minutes after the washing machine has come to a stop. The light (lid locked) is off. Turn the programme selector to the “Stop” position . Remove washing. Un- plug and close water inlet tap. Stand by : once the programme has finished after a few minutes the energy saving system will be enabled. The brightness of the display is reduced. By pressing any button the appliance will come out of the energy saving status. 6 www.zanussi.com
Programmes table Programme / Type of washingLoadAvailable options Cottons1) (30° - 90°) : White or colour, e.g. normally soiled work clothes, bed linen, table lin- en, body linen, towels.5,5 kgRinse hold, Prewash, Quick2), Eco3), Easy iron, Extra rinse, Delay start Synthetics (30° - 60°) : Synthetic fabrics, body linen, coloured fabrics, non-iron shirts, blou- ses.2,5 kgRinse hold, Prewash, Quick2), Eco3), Easy iron, Extra rinse, Delay start Delicates (30° - 40°) : For all delicate mate- rials, for example curtains.2,5 kgRinse hold, Prewash, Quick, Extra rinse, Delay start Wool (30° - 40°) : Machine washable wool carrying the labels “pure new wool, machine washable, does not shrink”.1,0 kgRinse hold, Delay start Handwash ( cold - 40°) : Very delicate items carrying the “wash by hand” label.1,0 kgRinse hold, Delay start Jeans (60°) : For washing denim clothes. The Extra rinse option is activated.3,0 kgRinse hold, Prewash, Easy iron, Delay start Sport (40°) : For very dirty outdoor sports clothes. The Prewash option is activated.2,5 kgRinse hold, Extra rinse, Delay start Curtains (40°) : For washing curtains. The Prewash option is activated.2,5 kgRinse hold, Extra rinse, Delay start Soak (30°) : 4) Soaking for very dirty wash- ing. The drum stops full of water.5,5 kgDelay start Rinses : Hand washed items can be rinsed in this programme.5,5 kgRinse hold, Easy iron, Extra rinse, Delay start Drain : Runs an empty cycle after a Rinse hold.5,5 kg Spin : A spin cycle from 500 to 1200/10005) after a Rinse hold option. 5,5 kgDelay start 1) Standard programmes for the Energy Label consumption values According to regulation 1061/2010, the “Cottons 60 °C with Eco option” and “Cottons 40 °C with Eco option” are respectively the “standard 60 °C cotton programme” and the “standard 40 °C cotton programme”. They are the most efficient programmes in terms of combined energy and water consumptions for washing normally soiled cotton laundry. The water temperature of the washing phase may differ from the temperature declared for the selected programme. 2) Not available together with Eco option. 3) Not available with programmes with wash temperatures of 40°C and above. 4) Put the detergent into the compartment marked . 5) Depending on model. 7 www.zanussi.com
Care and cleaning Unplug the appliance before cleaning. Descaling the appliance To descale the appliance, use an appropriate non-corrosive product designed for washing machines. Read product label for recommen- ded amounts and how often descaling should be carried out. The exterior Use warm soapy water to clean the exterior of the appliance. Never use alcohol, solvents or similar products. Dispenser box To clean, proceed as follows : 1 2 4 3 Drain filter Regularly clean the drain filter which is located at the bottom of the drum : 1 2 4 356 7 8 9 10 CLACK 11CLACK Water inlet filters To clean, proceed as follows : 8 www.zanussi.com
Operating Problems Numerous checks were carried out on your ap- pliance before it left the factory. However, should you notice a malfunction, please refer tothe sections below before contacting the after- sales service. ProblemsCauses The appliance doesn’t start or doesn’t fill :• the appliance isn’t plugged in correctly, the electrical installation isn’t work- ing, there is a power failure, • the lid of your appliance and the drum shutters aren’t closed firmly, • the programme start command hasn’t been properly selected, • the water supply has been cut off, the water inlet tap is closed, • the water inlet filters are dirty (see “Care and cleaning”). The appliance fills but empties straight away :• the drainage U-piece is fixed too low (see “Installation”). The appliance doesn’t rinse or doesn’t empty :• the drain hose is blocked or bent, • the object trap is obstructed (see “Care and cleaning” ), • the out of balance detector has been activated : washing is unevenly distrib- uted in the drum, • the “Drain” programme or “Night Cycle” or “Rinse hold” option have been selected, • the height of the drainage U-piece is unsuitable. The appliance doesn’t spin :• balance problem with the laundry load: add more laundry or manually adjust the items in the drum. You have found water around the appliance :• too much detergent has caused foam to overflow, • the detergent is unsuitable for machine washing, • the drainage U-piece isn’t attached correctly, • the water inlet hose is leaking. The washing results are not satisfactory :• the detergent is unsuitable for machine washing, • there is too much laundry in the drum, • the wash cycle is unsuitable, • there isn’t enough detergent. The appliance vibrates, is noisy :• all packaging have not been removed from the appliance (see “Installation” ), • the appliance isn’t level and is unbalanced (see “Installation” ), • the appliance is too close to the wall or furniture, • washing is unevenly distributed in the drum, the load is too small. • the appliance is in running in period, noise will disappear with time. The wash cycle is much too long :• the water inlet filters are dirty (see “Care and cleaning”), • the power or water supply has been cut off, • the water inlet temperature is lower than usual, • the foam detection security system has been activated (too much detergent) and the washing machine has begun draining the foam, • the out of balance detector has been activated: an extra phase has been added to distribute washing more evenly in the drum. 9 www.zanussi.com
ProblemsCauses The appliance stops during a wash cycle :• the water or electricity supply is defective, • a “Rinse hold” option has been selected, • the drum shutters are open. The lid doesn’t open at the end of the cycle :• the temperature inside the drum is too high, • the lid unlocks 1 - 2 minutes after the end of the cycle. The error code ap- pears in the display1) and the “Start/Pause” button flashes red 2) : • the lid is not closed properly. The error code ap- pears in the display1) and the “Start/Pause” button flashes red 2): • the object trap is obstructed, • the drain hose is blocked or bent, • the drain hose is fixed to high (see "Installation" ), • the drainage pump is blocked, • the standpipes are blocked. The error code ap- pears in the display1) and the “Start/Pause” button flashes red 2): • the water tap is closed, • the water supply has been cut off. Softener runs directly into the drum when filling the dispenser box:• you have gone past the MAX indicator. 1) On some models, the audible signals can sound 2) After solving any problems, press "Start/Pause" button to restart the interrupted programme. Detergents and Additives Only use detergents and additives designed for use in a washing machine. We do not recom- mend mixing different types of detergents. This may spoil the washing. There are no restrictions on the use of powder detergents. Liquid deter- gents must not be used when a prewash hasbeen selected. For cycles without prewash, pour the liquid detergent directly into the drum or use a special dosing device (supplied by the detergent's manufacturer). Detergent tablets or doses must be placed in the detergent com- partment of your appliance's dispenser box. Technical Specifications DIMENSIONSHeight Width Depth850 mm 400 mm 600 mm LINE VOLTAGE /FREQUENCY POWER CONSUMPTION FUSE 230 V / 50 Hz 2300 W 10 A Level of protection against ingress of solid particles and moistureIPX4 Water supplyCold water 10 www.zanussi.com