Zanussi Zwo 3101 User Manual

Caution! Make
sure that no
laundry stays be-
tween the seal and
the door. There is a
risk of water leakage
or damage to the
laundry.
Filling the detergent and additives
Caution! Use only specified detergents
for washing machine.
21
1The detergent compartment for the pre-
wash phase or for the soak programme.
Add the detergent for prewash and soak
before the start of the programme.
2The detergent compartment for the
washing phase.
If you use a liquid detergent, put it imme-
diately before you start the...

2. Turn the programme knob again to activate
the appliance. Now, you can set a new
washing programme.
The appliance does not drain the water.
Change a function
You can change only the delay and spin func-
tion before they operate.
Press the related button to set the new value.
Set the delay start
1. Press the delay start button again and
again until the display shows the number
hours.
2. Press the start button, the appliance starts
the countdown of the delay start. The sym-
bol h flashes in the display...

Descaling
The water we use contains limescale. If it be-
comes necessary, use a water softener to re-
move limescales.
Use a special product made for washing ma-
chines. Obey the instructions that you find on
the packaging of the manufacturer.
Do this separately from the laundry wash.
Maintenance wash
With the low temperature programmes it is
possible that some detergent stays in the drum.
Make regularly a maintenance wash. To do this:
• Empty the laundry from the drum.
• Set the hottest cotton wash...

1. Open the pump
door.
2. Put a container
below the recess
of the drain
pump to collect
the water that
flows out.
3. Unscrew the fil-
ter to let the wa-
ter flow out.
4. When the container is full of water,
screw the filter again and empty the con-
tainer. Do steps 3 and 4 again and again
until no more water flows out from the
drain pump.
1
2
5. Unscrew the fil-
ter and remove it.
6. Remove fluff and
objects from the
pump.
7. Make sure that
the impeller of
the pump can
turn. If this does
not occur, con-...

• Install again the inlet hose. Make sure that
the couplings are tight to prevent leakages.
• Open the water tap.
Emergency drain
Because of a malfunction, the appliance cannot
drain the water.
If this occurs, do steps (1) through (5) of 'To
clean the drain pump'.
If necessary, clean the pump.
When you drain the water with the emergency
drain procedure, you must activate again the
drain system:
1. Put 2 litres of water in the main wash com-
partment of the detergent dispenser.
2. Start the...

ProblemPossible causePossible solution
 The programme knob is not in the
correct position.Turn the programme knob in the correct po-
sition.
 The delay start is set.
It is available only for models with
the Delay start.To start immediately the programme, cancel
the delay start.
The appliance does not
fill with water.The water tap is closed.Open the water tap.
 The water inlet hose is damaged.Make sure that the water inlet hose has no
damages.
 The filter in the water inlet hose is
blocked .Clean the...

ProblemPossible causePossible solution
 The load is very small.Add more laundry in the drum.
The appliance fills with
water and drain immedi-
ately.The end of the drain hose is too
low.Make sure that the drain hose is in the cor-
rect position. Refer to 'Installation'.
The washing results are
not satisfactory.The detergent you used was not
sufficient or correct.Increase the detergent quantity or use a dif-
ferent one.
 You did not remove the stubborn
stains before you wash the laun-
dry.Use...

Installation
Unpacking
A
1. Use the gloves. With a cutter remove the
external film.
Do not to discard the plastic cover (A).
2. Remove the polystyrene packaging mate-
rials.
3. Remove the internal film.
4. Open the door and remove all the items
from the drum.
5. Put the front piece on the floor behind
the appliance. Carefully put down the ap-
pliance with the rear side on it. Make
sure not to damage the hoses.
18
 
www.zanussi.com
 

1
2
6. Remove the polystyrene protection from
the bottom.
A
7. Install the plastic cover (A), removed from
the top of the packaging, to the bottom
of the appliance. Remove the adhesive
strip and close the bottom of the appli-
ance. Attach permanently the plastic cov-
er to the bottom of the appliance with the
small plastic caps that you can find in the
user manual bag.
8. Pull up the appliance in vertical position.
2
1
9. Remove the four bolts with a key. Pull out
the plastic spacers. Remove the power...

Positioning and levelling
• Install the appliance on a flat hard floor.
• Make sure that carpets do not stop the air
circulation below the appliance.
• Make sure that the appliance does not
touch the wall or other units
x4 x4
• Loosen or tighten the feet to adjust the lev-
el. A correct adjustment of the appliance
level prevents the vibration, noise and the
movement of the appliance when in opera-
tion.
• The appliance must be level and stable.
Caution! Do not put cardboard, wood or
equivalent materials...