Zanussi Zwh 2101 User Manual

Using the liquid detergent
A
• Pull out the detergent
dispenser until it stops.
• Pull out the detergent
divider from its posi-
tion (A).
• Put it into the special
guides in the middle of
the compartment for the
washing phase.
• Measure out the detergent and the fabric conditioner.
• Carefully close the detergent dispenser.
When you use the detergent divider:
–Do not use gelatinous or thick liquid detergents.
– Do not put more liquid detergent than the edge of the
detergent divider.
– Do not set the...

• Remove the laundry from the appliance. Make sure that
the drum is empty.
• Keep the door ajar, to prevent mildew and odours.
• Close the water tap.
The washing programme is completed, but there is water
in the drum:
– The Rinse Hold option or a programme that stops with
water in the drum is set.
– The door stays locked and the start button indicator
flashes.
– You must drain the water before to open the door.
To drain the water:
1. If the spin speed option is available, you can de-
crease the spin...

• Press the lever and pull
the dispenser out.
• Remove the top part of
the liquid additive com-
partment.
Clean all the parts with
water.
• Clean the dispenser re-
cess with a brush.
• Put back the dispenser in the recess.
Drain pump
Regularly examine the drain pump and make sure
that it is clean.
Clean the pump if:
• The appliance does not drain the water.
• The drum cannot turn.
• The appliance makes an unusual noise because of the
blockage of the drain pump.
Warning! 
1.Disconnect the mains plug from...

1 2
8. Clean the filter under
the water tap and put
it back in the pump.
Caution! Make sure
that you tighten cor-
rectly the filter to prevent
leakages.
9. Close the drain pump door.
Clean the inlet valve filter
It could be necessary to clean the filter when:
• The appliance does not fill with water.
• The appliance fills with the water for a long time.
Warning! Disconnect the mains plug from the mains
socket.
To clean the filter:
• Close the water tap.
• Remove the inlet hose behind the appliance....

Warning! Deactivate the appliance before you do the
checks.
ProblemPossible causePossible solution
The appliance does not
start.The mains plug is not connected in
the mains socket.Put in the mains plug.
 The fuse in the box fuse is damage.Replace the fuse.
 The appliance door is open.Close the door firmly.
 You do not press the start buttonPress the start button.
 The programme knob is not in the
correct position.Turn the programme knob in the correct posi-
tion.
 The delay start is set.
It is available...

ProblemPossible causePossible solution
There is water on the floor.Leakages from the couplings of the
water hoses.Make sure that the couplings are tight.
 Leakages from the drain pump.Make sure that the drain pump filter is tight.
 The water drain hose is damaged.Make sure that the water inlet hose has no dam-
ages.
You cannot open the appli-
ance door.The washing programme is in oper-
ation.Let the washing programme end.
 There is water in the drum.Set the drain or the spin programme.
The appliance...

Installation
Unpacking
12
A
1. Use the gloves. With a scissor cut the straps and
with a cutter remove the external film.
Do not to discard the plastic cover (A).
2. Remove the polystyrene packaging materials.
3. Remove the internal film.
4. Open the door and remove all the items from the
drum.
 17 www.zanussi.com
 

5. Put the front piece on the floor behind the appli-
ance. Carefully put down the appliance with the
rear side on it. Make sure not to damage the ho-
ses.
1
2
6. Remove the polystyrene protection from the bot-
tom.
A
7. Install the plastic cover (A), removed from the top
of the packaging, to the bottom of the appliance.
Remove the adhesive strip and close the bottom of
the appliance. Attach permanently the plastic cov-
er to the bottom of the appliance with the small
plastic caps that you can find in...

10. Put the plastic caps in the holes. You can find
these caps in the user manual bag.
Warning! Remove all the packaging and the transit
bolts before you install the appliance.
We recommend that you keep the packaging and the
transit bolts for when you move the appliance.
Positioning and levelling
• Install the appliance on a flat hard floor.
• Make sure that carpets do not stop the air circulation
below the appliance.
• Make sure that the appliance does not touch the wall
or other units
x4 x4
• Loosen...

• On the edge of a sink.
Make sure that the plastic guide cannot move when
the appliance drains. Attach the guide to the water
tap or the wall.
• To a stand pipe with vent-hole.
Refer to the illustration. Directly into a drain pipe at a
height of not less than 60 cm and not more than 90
cm. The end of the drain hose must always be venti-
lated , i.e. the inner diameter of the drainpipe must
be larger than the external diameter of the drain
hose.
Without the plastic hose guide
• To a sink spigot.
Refer to...